Table of Contents
Advertisement
Troubleshooting chart (continued)
If trouble occurs
When this product is subjected to strong external interference (mechanical shock,
excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is
operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
Clearing all the memory (reset)
1 Unplug the unit.
2 Whilst holding down the ON/STAND-BY button, plug in the AC power lead.
At this time, the unit will not be turned on.
3 Press the ON/STAND-BY button again to turn the power on.
Caution:
This operation will erase all data stored in memory and restore various settings to the
initial status (default).
Before transporting the unit
1 Press the ON/STAND-BY button to turn the power on.
2 Open the disc compartment and remove the disc.
3 Close the disc compartment and enter the unit to stand-by mode.
4 After the power indicator goes off, unplug the unit.
Error indicators and warnings
When you load an unplayable disc or fail to perform operations properly, the following
messages are displayed on the unit and the TV screen.
Display
The disc is not loaded.
The disc is scratched or dirty and cannot be recog-
nised.
The disc is loaded up-side down.
The disc is scratched or dirty and cannot be played.
The disc does not satisfy the standards.
The disc is scratched or dirty and data cannot be
read.
The disc does not satisfy the standards.
The optical pickup cannot be located.
Set this unit to the stand-by mode and turn the power
on again. (*)
The unit considers the DVD mechanism is defective.
Place the unit away from noise source or plug the
AC power lead to another AC socket. (*)
The TV screen does not display correctly.
Place the unit away from noise source or plug the
AC power lead to another AC socket. (*)
The digital audio input socket is not connected prop-
erly.
Unspecified signal is received and cannot be recog-
nised.
The temperature is too high.
Set this unit to the stand-by mode and wait for a
while.
The speaker is not connected properly.
The amplifier is defective.
Set this unit to the stand-by mode and turn the power
on again. (*)
The amplifier is defective.
Set this unit to the stand-by mode and turn the power
on again. (*)
Meaning
– 11 –
Remote control
Test of the remote control
Face the remote control directly to the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy your
system.
Remote sensor
Display
The amplifier is defective.
Place the unit away from noise source or plug the
AC power lead to another AC socket. (*)
The cooling fan on the back of the main unit does not
run due to foreign objects caught in it.
Set this unit to the stand-by mode and remove the
foreign objects around the fan.
(*): Should the same message appear even if the unit is unplugged and plugged in or
is set to the stand-by mode and on again, contact your local dealer where you pur-
chased the unit.
TV screen
1 5
/
C
WRO NG D
I S
C
T
Y P
E
8 3
/
0
0 1
:
2 3 4 0
:
1 5
/
C
R EG
I O
N
CO E
D
E R OR
R
8 3
/
0
0 1
:
2 3 4 0
:
1 5
/
C
NO DISC
8 3
/
0
0 1
:
2 3 4 0
:
1
1 5.
h c
0
0
10
O
N
NO T
BIT RATE
Mbps
ON
A L OWE D
L
G
SELECT
ON
ENTER
ENTER
RETURN
S
1
1 5.
h c
0
0
10
O
N
A CC
E S
S
BIT RATE
Mbps
ON
D E
N
I E D
G
SELECT
ON
ENTER
ENTER
RETURN
S
SD-AT100H
0.2 m - 6 m
(8" - 20')
Meaning
Meaning
The disc cannot be played with this unit or the
disc is loaded in an incorrect way.
The region number of the DVD is not 2 or ALL.
A disc has not been loaded.
You are trying to perform an incorrect oper-
ation.
The operation is prohibited.
The disc does not support the operation de-
scribed in this operation manual.
Advertisement
Table of Contents
