Advertisement
Available languages
Available languages
Fax +32 2 359 95 50
Then put the ingredients into the bowl (fig. 6, page 6). We advise you to cut ingredients
like meat or vegetables into pieces beforehand in order to get a homogeneous
preparation.
Place the lid with feeding tube onto the processor bowl as indicated in paragraph "Use"
making sure the metal shaft of the blades gets into the hole in the middle of the lid (fig. 7
& 8, page 6).
Plug in the appliance.
For chopping, select a speed between 2 and 4. CAUTION: Do not try to chop very hard
food (such as ice, sugar or coffee beans...).
When you use your appliance in an intensive way, it is necessary to make breaks of at
least 1 minute between every operation to let the motor cool down.
b) Whisking
Do not use the whisking blade (16) to knead heavy dough such as tart pastry or pizza dough.
Make sure the appliance is unplugged, that the ON/OFF & speed switch (6) is in "0"
position and that the safety lid (20) is closed.
Place the processor bowl (10) onto the shaft (fig. 2, page 6) and turn it clockwise until the
handle reaches the switch connector (8) (fig. 3, page 6).
For whisking, place the blade support (18) onto the shaft (9) (fig. 4, page 6) and put the
whisking blade (16) on the support (18) (fig. 5, page 6).
Put the ingredients into the bowl.
Place the lid with feeding tube onto the processor bowl as indicated in paragraph "Use".
This accessory can be used to whisk egg whites and prepare sauces like mayonnaise or
custard.
Plug in the appliance and turn the ON/OFF & speed switch to a speed between 2 and 4.
It is possible to add ingredients during the process through the funnel of the lid.
When you use your appliance in an intensive way, it is necessary to make breaks of at
least 1 minute between every operation to let the motor cool down.
c) Grating / Slicing
Make sure the appliance is unplugged, that the ON/OFF & speed switch (6) is in "0"
position and that the safety lid (20) is closed.
Place the processor bowl (10) onto the shaft (fig. 2, page 6) and turn it clockwise until the
handle reaches the switch connector (8) (fig. 3, page 6).
Place the support (18) on the shaft (9) (fig. 4, page 6).
For grating, slide the grating blade (13) into its support (15) (fig. 9, page 6). For slicing, slide
the slicing blade (14) into its support (15) (fig. 9, page 6).
Place the whole on the support shaft (fig. 10, page 6).
Place the lid with feeding tube onto the processor bowl as indicated in paragraph "Use"
making sure the metal shaft of the blades gets into the hole in the middle of the lid (fig. 11,
page 6).
Cut the potatoes, carrots, cucumbers... into pieces and place the ingredients into the
funnel of the bowl lid.
Use the pusher (12) to push the food down the funnel (fig. 12, page 6). Never use your
fingers or any other utensil.
Plug in the appliance and turn the ON/OFF & speed switch to "1" to start. Adjust the
speed if necessary.
Always turn the ON/OFF & speed switch to "0" and unplug the appliance before emptying
the bowl and be careful when handling the blades, as they are very sharp.
When you use your appliance in an intensive way, it is necessary to make breaks of at
least 1 minute between every operation to let the motor cool down.
Copies of the I/B. Please reproduce them without any
changes
except
under
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't change
the page numbering. Keep the language integrity.
15
Assembly page 15/64
special
instruction
from
TKG HA 1006 - 140710
Team
Advertisement
