F016J11384-A Safety Notes Important! Warning! Read these instructions carefully, be familiar with the controls and the proper use of the lawnmower. Keep these instructions for future reference. Explanation of symbols on the lawnmower: General hazard safety alert Read instruction manual Beware of thrown or flying objects Keep bystanders at a safe distance from machine Switch off and remove isolation key before adjusting, cleaning and before leaving the...
Page 10
F016J11384-A Mow only in daylight or in good artificial light. Avoid operating the lawnmower in wet grass, where feasible. Walk, never run. Mowing on banks can be dangerous: – Mow across the face of slopes – never up and down. –...
F016J11384-A Technical Data Designation: Liberty 30 Liberty 35 Liberty 43 Cylinder lawnmower Part number LIBE30 LIBE35 LIBE43 Rated power 400W@10A 400W@10A 400W@10A Voltage (Max V) 40V Li-ion 40V Li-ion 40V Li-ion Blade width (cm) Height of cut (mm) 6-32 6-32 6-32 Grassbox capacity (I) ...
F016J11384-A Cable clips (C) Ensure that the cable clips supplied are used to fix the cables to the handle. Grass box (D) (Liberty 30 & 35 models) Squeeze the ends of the grass box cradle together and insert the pins into the pivot hole on the lawnmower.
Page 13
F016J11384-A If the red LED blinks of flashes please refer to the charger manual. If the battery has been stored with little to no charge for a long period of time, the charger will go into recovery mode, which will take 20 hrs to fully charge the battery. This will enhance the life of the battery.
Dispose of it (See “Disposal” section) and replace with a new battery pack. Do not attempt to repair. Use only Allett battery Ref: F016J11357 36V 4Ah 144Wh 40V MAX Use only Allett charger Ref: UK F016J11358 or EU F016J11359 Please refer to the Battery and Charger manual for further information.
F016J11384-A Adjustments & Maintenance STOP - Remove the isolator key and the batteries before making any adjustments and wear gloves if you are working near the blades Note: To ensure long and reliable service, carry out the following maintenance regularly. Regularly check for obvious defects such as a loose, dislodged or damaged blade, loose fixings, and worn or damaged components.
F016J11384-A Comb adjustment – Liberty 43 only Please refer to illustration (N). Your mower is fitted with an adjustable comb (13) which can be used on the lower heights of cut. It is set by loosening the screws (14) and rotating the comb until the tines just touch the ground. You may need to re-adjust after changing the height of cut.
Page 17
Blunt or dull blades will adversely affect cutting performance and battery life. Please contact your local dealer for information. You can search for your nearest registered dealer on-line at www.allett.co.uk/allett-dealer-locator Cleaning & Storage Clean the mower, battery and charger with a soft dry brush or cloth, paying particular attention to the cooling fins on the end of the motor and charger.
F016J11384-A next time you mow the lawn, try to work at right angles to the previous cut as this will help prevent unevenness in the surface. Unevenness can build up if you always mow in the same direction. The blades may require adjustment, particularly before first use – see “Adjusting blade” section. Protective circuit The lawn mower contains a protective circuit.
Page 19
F016J11384-A Service Useful videos are available on Youtube, search for “Allett Mowers” to find our channel. To locate your nearest Allett dealer/service agent go to: www.allett.co.uk/allett-dealer-locator Disposal Product, accessories and packaging should be sorted for environment-friendly recycling. The plastic components are labelled for categorised recycling.
F016J11384-A EU Declaration of Conformity We: Turfmech Machinery Ltd Of: Hangar 5, New Road, Hixon, Staffordshire, ST18 0PJ, UK Declare that equipment: Category 32 Electric lawnmower conforms to the essential requirements of the following directives and their amendments: 2006/42/EC, 2014/30/EU, 2000/14/EC (the conformity assessment procedure followed was in accordance with Annex VI of the Noise Directive) and has been designed and manufactured to the following standards: BS EN 60335-1, BS EN 60335-2-77.
Page 21
You must contact the place of purchase and report the problem to them. You need to have your proof of purchase and guarantee. If the dealer cannot assist in finding a solution to the problem reported, please contact Allett to report any unresolved issues. This guarantee does not apply if: –...
Page 22
F016J11384-A Notes: Your nearest dealer: Allett a division of Turfmech Machinery Limited, Hangar 5, New Road, Hixon, Staffordshire ST18 0PJ England F016J11384 5 / 2017 Original Instructions – English...
Need help?
Do you have a question about the Liberty Classic Push 30cm and is the answer not in the manual?
Questions and answers