Download Print this page

Honeywell 50206 Manual

Duval series.
Hide thumbs

Advertisement

DUVAL 52" CEILING FAN
MODELS #50201, 50206
Español p. 19
LISTED FOR DAMP
LOCATION
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,
8 am - 5 pm, EST.

Advertisement

   Related Manuals for Honeywell 50206

   Summary of Contents for Honeywell 50206

  • Page 1

    DUVAL 52” CEILING FAN MODELS #50201, 50206 Español p. 19 LISTED FOR DAMP LOCATION Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,...

  • Page 2: Table Of Contents

    WELCOME TABLE OF CONTENTS PREPARATION Care and Maintenance ......2 Before beginning the assembly of this product, ensure that all parts are present.

  • Page 3: Package Contents

    PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Blades (5) 2. Canopy 3. Mounting Bracket 4. Canopy Cover 5. Yoke Cover 6. Downrod 7. Blade Arm (5) 8. Motor Housing 9. Switch Housing 10.

  • Page 4: Safety Information

    SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199.

  • Page 5: Mounting Options

    MOUNTING OPTIONS Fig. 1 DANGER Turn off the circuit breakers and the wall switch to the fan supply line leads. Failure to disconnect the power supply prior to installation may result in serious injury or death. 1. Your fan has 3 mounting options: •...

  • Page 6: Mounting Bracket Installation

    MOUNTING BRACKET INSTALLATION 4. Loosen the four mounting bracket screws. Remove Fig. 4 the two mounting bracket screws from the round holes of canopy. Set aside for later use. Detach Mounting Mounting mounting bracket from canopy (Fig. 4). Bracket Bracket Screws Mounting Washer...

  • Page 7: Standard Or Angle Mounting Instructions

    STANDARD OR ANGLE MOUNTING INSTRUCTIONS 6. Partially loosen the set screws in the yoke at the Fig. 6 top of the motor housing (Fig. 6). Set Screws 7. Remove the downrod pin and downrod clip from Fig. 7 the downrod (Fig. 7). Downrod Clip Downrod Pin...

  • Page 8

    STANDARD OR ANGLE MOUNTING INSTRUCTIONS 9. Slide the downrod into the yoke of the motor Fig. 9 Downrod housing, align the holes, and re-install the downrod pin and downrod clip. Then re-tighten the set Downrod screws (Fig. 9). Downrod Clip Downrod Pin Set Screw Downrod Clip...

  • Page 9

    STANDARD OR ANGLE MOUNTING INSTRUCTIONS 12. Install the downrod ball into the mounting bracket Fig. 12 opening. Align the slot in the downrod ball with the tab in the mounting bracket. The rod should not rotate if installed correctly (Fig. 12). Slot Mounting Bracket...

  • Page 10: Closemount Instructions

    CLOSEMOUNT INSTRUCTIONS 13. Remove the canopy cover from the bottom of the Fig. 13 canopy (Fig. 13) Helpful Hint: The downrod, hanging ball, and canopy cover are not used in this type of installation. Canopy Cover Canopy 14. Align the canopy with the closemount screw holes Fig.

  • Page 11: Wiring

    WIRING WIRING Fig. 16 CAUTION Be sure outlet box is properly grounded or that a ground (green or bare) wire is present. Black (live) WARNING White (neutral) If house wires are different colors than referred to in the following step, stop immediately. A professional Bare/Green (ground) electrician is recommended to determine wiring.

  • Page 12: Canopy Installation

    CANOPY INSTALLATION 18. Lift the canopy up so the partially installed mounting Fig. 18 bracket screws are situated in the L-slots on each side of the canopy. Rotate the canopy clockwise and install the remaining mounting bracket screws and washers from Step 4 (Fig. 18). Mounting Mounting Bracket Screw...

  • Page 13: Blade Installation

    BLADE INSTALLATION 19. Remove motor screws from underside of motor and Fig. 19 save for blade arm attachment. If there are plastic motor blocks installed with the motor screws, discard the plastic motor blocks but keep the screws (Fig. 19). Motor Block Motor Screw Motor Screw...

  • Page 14: Switch Housing Installation

    SWITCH HOUSING INSTALLATION 22. Remove the three screws from the upper switch Fig. 22 housing. Connect plug from the motor to the plug from the switch housing cap. Align holes in the switch housing cap with holes in upper switch housing.

  • Page 15: Operating Instructions

    OPERATING INSTRUCTIONS 23. Use the fan reverse switch, located on the side Fig. 23 of the light kit, to optimize your fan for seasonal performance (Fig. 23). Using a ceiling fan will allow you to raise your thermostat in the summer and lower your thermostat in the winter without sacrificing comfort.

  • Page 16: Replacement Parts List

    REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. MODEL 50201 MODEL 50206 PIECE DESCRIPTION PART # PART # Blade Arm...

  • Page 17: Troubleshooting

    TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for added protection.

  • Page 18: Limited Lifetime Warranty

    Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell International Hong Kong China Electric Appliance Manufacture Co., Ltd.

This manual also for:

50201, Palm island, 50203

Comments to this Manuals

Symbols: 0
Latest comments: