Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell 50202
Summary of Contents for Honeywell 50202
- Page 1 PALM ISLAND 52” CEILING FAN MODEL #50202 Español p. 21 LISTED FOR DAMP LOCATION Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,...
-
Page 2: Table Of Contents
WELCOME TABLE OF CONTENTS PREPARATION Before beginning the assembly of this product, ensure Care and Maintenance ......2 that all parts are present. -
Page 3: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Canopy 2. Mounting Bracket 3. Canopy Cover 4. Downrod 5. Yoke Cover 6. Motor housing 7. Switch Housing 8. Glass Shade 9. Light Kit 10. -
Page 4: Safety Information
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199. -
Page 5: Mounting Options
MOUNTING OPTIONS DANGER Fig. 1 Turn off the circuit breakers and the wall switch to the fan supply line leads. Failure to disconnect the power supply prior to installation may result in serious injury or death. 1. Your fan has 3 mounting options: •... -
Page 6: Mounting Bracket Installation
MOUNTING BRACKET INSTALLATION 4. Loosen the four mounting bracket screws. Fig. 4 Completely remove the two mounting bracket screws and washers from the round holes of Mounting Mounting canopy. Set aside for later use. Detach mounting Bracket Bracket Screws bracket from canopy (Fig. 4). Washer Mounting Bracket Washer... -
Page 7: Standard Or Angle Mounting Instructions
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 6. Partially loosen the two set screws in the yoke at Fig. 6 the top of the motor housing (Fig. 6). Set Screws Fig. 7 7. Remove the downrod pin and downrod clip from the downrod (Fig. 7). Downrod Clip Downrod Pin... - Page 8 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 9. Slide the downrod into the yoke of the motor Fig. 9 Downrod assembly, align the holes, and re-install the downrod pin and downrod clip. Then re-tighten the set screws (Fig. 9). Downrod Downrod Clip Downrod Pin Set Screw Downrod Clip...
- Page 9 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 12. Install the downrod ball into the mounting bracket Fig. 12 opening. Align the slot in the downrod ball with the tab in the mounting bracket. The downrod should not rotate if installed correctly (Fig. 12). Slot Mounting Bracket...
-
Page 10: Closemount Instructions
CLOSEMOUNT INSTRUCTIONS 13. Remove the canopy cover from the bottom of the Fig. 13 canopy (Fig. 13) Helpful Hint: The downrod, hanging ball, and canopy cover are not used in this type of installation. Canopy Cover Canopy 14. Align the canopy with the closemount screw holes Closemount Fig. -
Page 11: Wiring
WIRING Fig. 16 CAUTION Be sure outlet box is properly grounded or that a ground (green or bare) wire is present. Black (live) WARNING White (neutral) If house wires are different colors than referred to in the following step, stop immediately. A professional Bare/Green (ground) electrician is recommended to determine wiring. -
Page 12: Canopy Installation
CANOPY INSTALLATION 18. Lift the canopy up so the partially installed Fig. 18 mounting bracket screws are situated in the L-slots on each side of the canopy. Rotate the canopy clockwise and install the remaining mounting bracket screws and washers from Step 4 (Fig.18). Mounting Mounting Bracket... -
Page 13: Blade Installation
BLADE INSTALLATION 19. Remove motor screws from underside of motor and Fig. 19 save for blade arm attachment. Discard the plastic motor blocks and washers but keep the motor screws (Fig. 19). Motor Motor Screw Motor Screw Washer Motor Block Block Fig. -
Page 14: Light Kit Installation
LIGHT KIT INSTALLATION To install the fan without a light kit, skip to Step 28. Fig. 22 22. Remove screws and washers from the switch housing cap. Then connect the single pin connectors from the switch housing to the single pin connectors from the switch housing cap -- Screw and Switch... -
Page 15: Light Kit
LIGHT KIT INSTALLATION 25. Remove the pre-installed rubber washer, nut, finial Fig. 25 cap, and finial from the light kit (Fig. 25). Rubber Washer Finial Cap Finial 26. Feed pull chain through the center hole in the Fig. 26 glass globe, rubber washer and nut. Lift the glass globe and rubber washer over the threaded rod. - Page 16 INSTALLATION WITHOUT LIGHT KIT 28. (Optional) To install the fan without a light kit: Fig. 28 Hex Nut Unscrew the nut located inside the switch housing Light cap from the threaded rod in the center of the cap Pull Chain to remove the light kit from the switch housing cap (Fig.
-
Page 17: Operating Installation
OPERATING INSTRUCTIONS 30. Use the fan reverse switch, located on the side Fig. 30 of the light kit, to optimize your fan for seasonal performance (Fig. 30). Using a ceiling fan will allow you to raise your thermostat in the summer and lower your thermostat in the winter without sacrificing comfort. -
Page 18: Replacement Parts List
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. MODEL 50202 PIECE DESCRIPTION PART # Blade Arm 50202-A Blade 50202-B... -
Page 19: Troubleshooting
TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. -
Page 20: Limited Lifetime Warranty
1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST.. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell International Hong Kong China Electric Appliance Manufacture Co., Ltd.