Operating Instructions 使用說明書 Arahan Penggunaan Steam Iron Household Use Only 蒸氣電熨斗 僅限家庭使用 Seterika Wap Penggunaan Rumah Sahaja NI-WT980 Model No. 型號 NI-WT960 Model English ...........3 繁體中文 .........18 Melayu ...........33...
How to use as a dry iron........12 How to care for and store your iron.....13 Q&A..............16 Trouble shooting...........17 Specifications.........17 Thank you for purchasing this Panasonic product. Before operating this unit, please read these instructions completely and save them for future use.
Safety precautions To reduce the risk of injury, loss of life, electric shock, ﬁre, and damage to property, always observe the following safety precautions. Explanation of symbols The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.
WARNING Never modify, disassemble, or repair. - Doing so may cause ignition or injury due to abnormal operation. Contact an authorized service center for repair. Do not immerse the iron in water or other liquids. - Doing so may cause burns, electric shock or ﬁre due to a short circuit. To reduce the risk of personal injury, electric shock or fire, please observe the following: Always ensure the appliance is operated on an electric power source...
WARNING If the Power Cord is damaged, it must be replaced by authorized personnel. - Failure to do so may cause an accident or injury. The iron is not to be used if it has been dropped, and there are visible signs of damage or if it is leaking.
CAUTION Do not store the Power Cord coiled with sharp angles. - This may damage the cord. Do not repeatedly and quickly press the Power Shot Button. - If repeating operation over an interval of less than 2 seconds, burns due to hot water leaks may result.
Parts identiﬁ cation Thermostat Operating Indicator Maximum Water Level Indicator Light Self-Cleaning Button Handle Power Switch [ Spray Mist Button Water Tank Power Shot Button Heel Rest Steam/Dry Selector Power Cord Accessory Water Fill Cover Power Plug Power type may vary Spray Nozzle comply with respective Soleplate...
Check for the correct water ﬁll level with the iron in the Heel rest position. Close the Water Fill Cover. Note • Do not overﬁll the Water Tank. Steam will release through the vents when the iron is positioned vertically. •...
Use iron after holding the iron horizontally and setting the Steam/Dry Selector to the Steam position. • Whenever the iron is positioned vertically, the steaming action will stop. 3 position Steam/Dry Selector Low steam High steam CAUTION: Do not aim the steam at any parts of your body or others. Note •...
How to use the “Power Shot” feature The “Power Shot” feature provides extra steam which goes deep into the garment and is helpful for removing stubborn wrinkles. If you have not used the “Power Shot” feature in a long time, it is necessary to clean the inside of the iron before using this feature on any clothes to be ironed.
How to use the “Vertical Steam” feature To get better results when using vertical steam, hang the garment on a hanger. Curtains and drapes may also be steamed once they are hung. Hold the iron away from your body, close to but not touching the fabric. Pull the fabric tightly and pump the Power Shot Button at 5 seconds intervals as you press the iron over the wrinkled fabric.
Set the Power Switch to “ ”. The Thermostat Operating Indicator Light switches on. • If the temperature of the Soleplate is high, the Thermostat Operating Indicator Light will not turn on. Use iron after preheating the iron until the Thermostat Operating Indicator Light switches out, which usually takes about 1 minute.
►METHOD(2) Using the “Power Shot” feature 1. Repeat steps 1 to 4 as described in “METHOD(1)”. 2. Hold the iron horizontally over the sink after the Thermostat Operating Indicator Light has gone out. 3. Pump the Power Shot Button quickly (at least 3 times per second) about 20-30 times.
Electronic 3-way auto shut-off function (NI-WT980 only) ・ The Auto Shut-Off feature is not intended to take the place of unplugging the cord. The Auto Shut-Off system works regardless of the position of the Power Switch. 1. When the iron is left idle with its Soleplate facing down or on its side for approx.
5. Wait until the iron has cooled before storing it, and always set it on the Heel Rest to protect the Soleplate from scratches, corrosion or stains. ►Surface of the iron • After unplugging and cooling the iron, simply wipe off with a damp cloth and if necessary, use a mild detergent.
Empty the Water Tank and ﬁll it with clean Clothes are marked water. There may be contaminants in the iron/cup. Speciﬁcations Model No. NI-WT980 NI-WT960 Power Source 220-240 V 50-60 Hz Power Consumption 2 400-2 800 W 2 000-2 400 W 2 200-2 600 W Weight (approx.)