Execution Of Adjustment; Adjustment Of Servo And System Controller; System Code Setting; Automatic Adjustment - Sharp VL-Z400H-T Service Manual

[Execution of adjustment]

Adjustment of servo and system controller

1. System code setting

It is necessary to set the following data items after replacing IC705 (E
<Adjusting method>
Select the VCR adjustment mode and set the data value at each address.
Code
Address
Z400S(ST)
Z400H(HT)
Z500S(SS/AS)
Z500S(RS)
Z500E(ES/WS/ET/WT/XT)
Z500H(HS)
Code
Address
Z400S(ST)
Z400H(HT)
Z500S(SS/AS)
Z500S(RS)
Z500E(ES/WS/ET/WT/XT)
Z500H(HS)

• Automatic adjustment

Mode VCR ADJ mode
Adjusting 1) Using command 12, select the VCR adjustment mode.
method 2) Using command 20, enable writing to the E
3) Using command 22, set the above-shown system codes according to the model.
4) Using the command, inhibit writing to the E
5) Using the command, exit the VCR adjustment mode.
Examples • Replacement of E
• Manual adjustment
Mode VCR ADJ mode
Adjusting 1) Set the CAM/OFF/VCR selector switch to VCR.
2) Press "CONTINUE" → "VCR adjustment" on the remote control to enter the VCR ADJ mode.
method
(At this time, "VCR ADJ" is displayed in the lower left part.)
Enter the specified value at each address.
· Shown below is the procedure for setting.
3) Select an address by increasing or decreasing the flashing numeric value with the FF or REW key
and press the PB key to confirm it.
4) Set the flashing numeric value to the specified value by increasing or decreasing it with the FF or
REW key and press the PB key to confirm it.
5) Press the STOP key to make it possible to select an address.
6) Repeat steps (3), (4) and (5) above until all the data items are set. Then press "CONTINUE" to exit
the VCR ADJ mode.
7) Set the CAM/OFF/VCR selector switch to OFF.
Examples ·Replacement of E
2. Adjustment of HSWP
Mode VCR ADJ mode
Adjusting 1) Select the video mode and play back the alignment tape.
2) Press "CONTINUE" → "HSWP ADJ" keys on the remote control.
method
→ HSWP adjustment execution (When the adjustment is completed, "GOOD" is displayed on the LCD and
ejecting is performed automatically.)
If adjustment cannot be made, "NG" is displayed on the LCD.
Examples · Replacement of mechanism · Replacement of E
Specifications Destination Specifications
01 09 02 0A
89 76 0A F5
89 76 0D F2
99 66 0A F5
99 66 2A D5
99 66 0B F4
99 66 0D F2
1394/exif model name
1A1 1A2 1A3 1A4 1A5 1A6
56 4C 2D 5A 34
56 4C 2D 5A 34
56 4C 2D 5A 35
56 4C 2D 5A 35
56 4C 2D 5A 35
56 4C 2D 5A 35
2 PROM (IC705)
2
PROM (IC705)
2
PROM).
Menu setting
03 0B 04 0C
D6 29 00 FF
DE 21 00 FF
54 AB 00 FF
54 AB 00 FF
5C A3 00 FF
5C A3 00 FF
1A7 1A8 1A9 1BD 1BE 1BF
30 30 53 00 00
30 30 48 00 00
30 30 53 00 00
30 30 53 00 00
30 30 45 00 00
30 30 48 00 00
2 PROM.
2 PROM.
2 PROM
29
VL-Z400S-T/H-T
VL-Z500S-S/H-S/E-T/E-S
Software switching Calendar
05 0D 07 0F
00 FF 04 FB
00 FF 04 FB
00 FF 04 FB
00 FF 04 FB
00 FF 04 FB
00 FF 04 FB
00 00
00 00
00 00
00 00
00 00
00 00