Advertisement
GETTING TO KNOW YOUR TOOL
Unpacking your Hammer Drill Kit
Your cordless Hammer Drill requires minimal assembly before use, remove all contents
from the box. Inspect the tool carefully to make sure no breakage or damage has occurred
during transport. If any parts are missing, do not attempt to use the tool until you have
obtained the missing parts from your King Canada retailer.
Contents:
1- Cordless Hammer Drill
4- SDS+ Drill bits
1- SDS+ 3/8" keyless chuck
1- Depth stop rod
1. 360
control handle
6. Speed range selector
0
2. SDS+ chuck
7. Battery/rotation indicator
3. Depth stop mount
8. Battery indicator button
4. Depth stop adj. button
9. Forward/reverse/lock
5. Drill/hammer selector
10. Variable speed trigger
SPECIFICATIONS
Model ........................................................................................................................8045L
Voltage ................................................................................................................20V MAX
Speeds (RPM) ........................................................................................2 (0-300/0-1,000)
Capacities (Concrete/Steel/Wood) ..............................................................7/8", 3/8", 7/8"
Weight ........................................................................................................................4 lbs
Battery types (not included) ..........1.3Ah (Mod. K-020LBT) or 3.0Ah (Mod. K-023LBT-3)
Battery charger (not included) ..................................................................Mod. K-020LCG
Figure 1
11. Battery compartment
12. SDS+ 3/8" keyless chuck
13. Depth stop rod
14. 4 SDS+ drill bits
OPERATION
USING YOUR 20V MAX LITHIUM-ION CORDLESS
HAMMER DRILL KIT
Important Note: This Cordless Hammer Drill Kit does
not come with a battery or charger, if you already own a
20V max Li-ion cordless tool you may use its battery
(K-020LBT) and charger (K-020LCG) as they are
interchangeable. If not, it will be necessary to purchase a
battery and charger.
WARNING: Do not install battery until the accessory is
installed securely to the tool. Wear protective gloves
and safety glasses, an accessory can become extremely
hot during operation, danger of burns!
Charging the battery/battery level indicator
20V max Li-ion batteries come with a battery power level
indicator (A) Fig.2, press the button (B) to see the charge
level. If the battery level is low charge the battery. To
charge the battery (C) Fig.2, plug charger (D) power cord
into a 120V AC receptacle (do not use extension cord).
The green LED (E) will flash to indicate power to the
charger. Align the grooves the battery with those of the
charger and slide the battery all the way until it snaps into
place. The red LED (F) will light up indicating the
charging procedure has begun. Once the green LED (E)
lights up, the battery is fully charged and ready to use.
Press the battery clip (B) Fig.3 to remove battery from
charger.
Installing/removing battery from drill
To install a battery (A) Fig.3 to the base of the cordless
Hammer Drill, align the grooves of the battery with those
of the base and slide the battery all the way until the
battery clip (B) snaps and holds the battery into place.
To remove the battery from the base, press the battery
clip (B) Fig.3 and slide the battery away from the base.
Turning Tool On/Off
To turn your hammer Drill ON, press the trigger (A) Fig.4.
Release the trigger to turn your Hammer Drill OFF.
Forward/Reverse/Lock switch
Warning! This tool must be stopped before the fwd/rev switch (B) Fig.4 can be used.
Otherwise you could damage the tool. The fwd/rev switch (B) is used to switch between
right and left rotation. When the switch is in the middle position the trigger (A) is locked and
cannot be pressed. To avoid accidental starts, always set the fwd/rev switch in the middle
position.
Figure 2
Figure 3
Figure 4
Advertisement
