Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Camos CWM-500
Summary of Contents for Camos CWM-500
-
Page 1: Instruction Manual
CWM-500 5” WATERPROOF MONITOR INSTRUCTION MANUAL Thank you for purchasing this product. For proper usages and application, Please read this instruction manual thoroughly. ver. 1.0 * Design and specifications are subject to change without notice. PRINTED IN KOREA... -
Page 2: Table Of Contents
CONTENTS SAFEGUARD INSTRUCTIONS ........3 FEATURE ................5 BOX CONTENTS ..............5 FUNCTION OF EACH PART ..........6 FUNCTION ................. 7 SETTING ................9 INSTALLATION and CONNECTION ......11 SPECIFICATION ............. 13... -
Page 3: Safeguard Instructions
SAFEGUARD INSTRUCTIONS 5” WATERPROOF MONITOR Please read the “Safety Rules” carefully before using this product. Following the safety rules pre- vents users from damages related with the misuse of the product. It is very important to follow these safety rules. We state “Caution” and “Warning” to clarify any potential risk for a damage associated with the misuse of the product. - Page 4 WARNING Do not put the product in place where sudden temperature increasing and should use on optimum voltage, temperature and humidity. - It may cause to electronic shock or malfunction. Do not place near of air bag effective range. - It may cause malfunction of air bag or accident, injury due to hitting monitor by air bag.
-
Page 5: Feature
FEATURE 5” WATERPROOF MONITOR • Water Resistant (IP-67), Aluminum housing • Application of TFT LCD with high resolution and low reflection • All functions are displayed on screen (OSD function) • PWM volume control • Mode selection function (3 Mode) •... -
Page 6: Function Of Each Part
FUNCTION OF EACH PART 5” WATERPROOF MONITOR 1. LCD SCREEN QVGA (320x234) 2. STAND BY LED Stand by lamp 3. BUTTONS DIMMER, LEFT, RIGHT, MODE, MENU, POWER 4. SUN VISOR HOLE Sun Visor installation hole 5. SPEAKER HOLE Speaker hole (Waterproof) 6. -
Page 7: Function
FUNCTIONS 5” WATERPROOF MONITOR POWER ON / OFF 1. Press POWER button for power ON. (Stand-by LED is OFF) 2. Press POWER button again for power OFF. (Stand-by LED is ON) MODE CAM1 CAM2 CAM3 1. Press MODE button. 2. CAM1 - CAM2 - CAM3 - CAM1 appears on the screen. 3. - Page 8 Screen switch while trigger input What is <Trigger input> or <Trigger signal>? We call it when a circuit works by a signal for example if driver uses right/left turn signal or reverse gear, the monitor shows connected camera screen on driving mode. * Below example is set with TRG1(Left signal light)=CAM1 / TRG2(Right signal light)=CAM2 / TRG3(Rear light)=CAM3.
-
Page 9: Setting
SETTING 5” WATERPROOF MONITOR 1. Use MENU button to change MAIN MENU (SETUP - PICTURE - CAMERA) CONTRAST DIMMER CAM1 NORMAL BRIGHTNESS LANGUAGE ENGLISH COLOR DIRECTION 0˚ TINT RESET 2. Use MODE button to select SUB MENU and then use LEFT/RIGHT button to adjust. ADJUST SELECT DIMMER... - Page 10 PICTURE 1. Use MODE button to select CONTRAST, BRIGHTNESS, COLOR, TINT menu. CONTRAST (Selected menu is in red.) BRIGHTNESS COLOR 2. Press LEFT/RIGHT button to adjust the number. TINT CAMERA CAM1 NORMAL CAM1 MIRROR Connected camera NORMAL / MIRROR selecting function In CAM2(or CAM3) Mode, CAM2(or CAM3) NORMAL/MIRROR is adjusted.
-
Page 11: Installation And Connection
INSTALLATION and CONNECTION 5” WATERPROOF MONITOR INSTALLATION Double side adhesive tape Double side adhesive tape Double side adhesive tape Double side adhesive tape Screw hole Sun Visor should be installed with 4 screws. -
Page 13: Specification
SPECIFICATION 5” WATERPROOF MONITOR Screen size 5 inch Resolution QVGA (320x234) LCD Panel Brightness 400cd/m² Contrast ratio 400:1 View angle(L/R/U/D) 70˚ / 70˚ / 40˚ / 60˚ Voltage DC 12V ~ 24V Power Supply Current 450mA (DC 12V, monitor set only) Input System NTSC / PAL NTSC... - Page 14 MEMO...
- Page 15 MEMO...
- Page 16 INSTRUCTION MANUAL...