CM-708R 7” TFT LCD COLOR MONITOR LANGUAGE VEHICLE 7” TFT LCD INSTRUCTION MANUAL Thank you for purchasing this product. For proper usages and application, please read this instruction manual thoroughly. ver. 1.0 PRINTED IN KOREA...
SAFEGUARD INSTRUCTIONS 7” TFT LCD COLOR MONITOR Please read the “Safety Rules” carefully before using this product. Following the safety rules prevents users from damages related with the misuse of the product. It is very important to follow these safety rules. We state “Caution” and “Warning”...
Page 4
WARNING Do not put the product in place where sudden temperature increasing and should use on optimum voltage, temperature and humidity --- It may cause to electronic shock or malfunction. Do not get product wet and operate with wet hands. --- It may cause to electronic shock or malfunction.
FEATURE 7” TFT LCD COLOR MONITOR • 8bit MICRO controller • TFT LCD with high resolution and low reflection • All functions are displayed on screen (OSD function) • PWM volume control • Mode selection function • Low energy consuming rate •...
FUNCTION OF EACH PART 7” TFT LCD COLOR MONITOR [ MONITOR ] Power or Stand-by status display Power ON/OFF button CAM1/CAM2/AV selection function SETUP/PICTURE selection function SOUND/MENU level control...
Page 7
[ REMOTE CONTROLLER ] Power ON/OFF button Selecting CAM1/CAM2/AV Selecting MENU and changing functions Changing volume or MENU level Moving Up/Down on MENU Mute mode On/Off Displaying the current channel and volume level Adjusting the screen setting...
FUNCTIONS 7” TFT LCD COLOR MONITOR POWER 1) Press [POWER] button to the power. (STAND BY state is OFF) 2) Press [POWER] button again to off the power. (STAND BY state is ON) MODE • It is a function to change video signal. CAM1 1) Press [MODE] button.
Page 9
MENU • It is a function to select MAIN MENU (SETUP/PICTURE/CAMERA) 1) Press [MENU] button to select MAIN MENU, changed color in red when it is selected. SETUP PICTURE CAMERA 2) Press [MODE] button to select SUB MENU, UP/DOWN button to change SUB MENU. DIMMER CONTRAST LANGUAGE...
Page 10
• DISPLAY WIDE NORMAL CINEMA FULL • MARKER (1) Press MENU button on CAM1, full screen mode. (2) Press MODE button and select MARKER. (3) Then, press [DOWN/UP] button on the monitor DIMMER or [◀▶] button on the remote control, select LANGUAGE ENGLISH DIRECTION...
Page 11
(2) Press MODE button and select H / V. (H: horizontal / V: vertical ) ress [DOWN/UP] button on the monitor or [◀▶] button on the remote control, and switch marker pattern. (H = -10~+10, V= -12~+12, Default setting: H=0, V=0) (4) After 10 seconds, set up screen disappears, and set up finishes.
Page 12
[ 2. PICTURE USER ] 1) [MODE] button to select CONTRAST, BRIGHTNESS, COLOR, TINT MENU. (Selected menu in red) 2) Push [UP/DOWN] button to change the settings of the diferent menu points. CONTRAST CONTRAST BRIGHTNESS BRIGHTNESS COLOR COLOR TINT TINT CONTRAST CONTRAST BRIGHTNESS...
Page 13
AUTOPIC • When press the AUTO PIC button, PICTURE SETUP menu is displayed on screen. CONTRAST BRIGHTNESS COLOR TINT MUTE • This function can be operated by the remote control. 1) Press [MUTE] button to mute sound and display mute icon. RECALL CAM1 VOLUME...
CHANGING REMOTE CONTROL BATTERY 7” TFT LCD COLOR MONITOR 1. Pull the battery cover to the direction of the arrow. 2. Place a battery with the (+) sign upward. (No. CR2025) 3. Put the battery case back into the remote control in the direction of the arrow.
INSTALLATION 7” TFT LCD COLOR MONITOR (1) Please set the place for Monitor installation. Clean the place where to install stand and install stand firmly after removing protect tape of stand bottom. (2) Fix the stand with enclosed screws. (3) Assemble the monitor to stand and fix it in the right angle. (4) Connect cable as follows.
SPECIFICATION 7” TFT LCD COLOR MONITOR SPECIFICATION ITEM NTSC SCREEN SIZE 17.78 cm (7.0 inch) DISPLAY FOMAT 800(H) x 3(RGB) x 480(V) LCD PANEL BRIGHTNESS 400 cd/m Contrast ratio 500:1 ACTIVE AREA 154.08 (W) x 86.92 (H) mm VIEW ANGLE 70˚(L) / 70˚(R) / 50˚(U) / 70˚(D) VOLTAGE DC 12V - 24V...