Table of Contents
Related Manuals for Jet TPFA-X
Summary of Contents for Jet TPFA-X
- Page 1 Operating Instructions and Parts Manual Table Powerfeed Models TPFA-X, TPFA-Y, TPFA-Z 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-350194 Ph.: 800-274-6848 Revision B1 08/2014 www.jettools.com Copyright © 2014 JET...
-
Page 2: Warranty And Service
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason ®... -
Page 3: Table Of Contents
2.0 Table of Contents Section Page 1.0 Warranty and Service ............................. 2 2.0 Table of Contents ............................3 3.0 Safety Warnings ............................. 4 4.0 About this manual ............................5 5.0 Specifications ..............................6 6.0 Setup and Assembly ............................6 ... -
Page 4: Safety Warnings
5. Do not use this powerfeed for other than its 16. Provide for adequate space surrounding work intended use. If used for other purposes, JET area and non-glare, overhead lighting. disclaims any real or implied warranty and holds itself harmless from any injury that may 17. -
Page 5: About This Manual
If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Specifications
Shipping dimensions ..10.5”L x 6.9”W x 14.56”H ..10.5”L x 6.9”W x 14.56”H ..10.5”L x 6.9”W x 14.56”H The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Shipping Contents
N – Bushing P – Nut (p/n TPFA2-0001) Figure 2 R – Spacer Accessories – TPFA-X S – Plate w/fasteners T – Roll pin U – T-way track pieces w/ fasteners V – Connector base W – Limit switch mounting bracket w/ screws X –... -
Page 8: X-Axis Installation And Features
6.3 X-Axis installation and features Figure 5... -
Page 9: X-Axis Installation
6.4 X-Axis installation 13. Place the limit switch over the holes and secure with two 3/8 x 1” socket head cap Refer to Figure 5: screws provided. See Figure 6. If the actuators 1. Move table to extreme left-hand position. are not symmetrical, grind them to obtain the proper position. -
Page 10: Z-Axis (Knee-Lift) Installation
6.6 Z-Axis (Knee-lift) installation 6.6.1 Z-Axis track Refer to Figure 9 to install Z-axis track. Figure 7 6.5.2 Y-Axis powerfeed Figure 8 shows installation of Y-Axis powerfeed. These instructions are similar (with the exception of the adaptor) to those in section 6.4, steps 1 through 10. - Page 11 6.6.2 Z-Axis powerfeed Refer to Figure 10: 1. Remove hand crank, clutch insert, dial, dial nut, dial holder and bearing flange. 2. Install extension shaft by screwing it onto the table elevating shaft. Important: • Shaft end must be against inner ring of bearing.
-
Page 12: Electrical Connections
6.7 Electrical Connections properly grounded outlet can be installed by a qualified electrician. This adapter is not permitted in Canada. The green-colored rigid ear, lug, and Electrical connections must the like, extending from the adapter must be made qualified electrician connected to a permanent ground such as a compliance with all relevant codes. -
Page 13: Troubleshooting
7.0 Troubleshooting Trouble Probable Cause Remedy No incoming power. Check plug connection. Powerfeed will not Powerfeed switch is off. Turn switch to ON position. work; power indicator is not lit. Circuit breaker on powerfeed has been Reset circuit breaker. tripped. Open unit by loosening bottom four Carbon brush is not making proper screws. -
Page 14: Table Powerfeed – Exploded View
8.1.1 Table Powerfeed – Exploded View... -
Page 15: Table Powerfeed – Parts List
Index No. Part No. Description Size 1 ....TPFA2-PT000-11 ..Top Housing ............ TPFA-X ........1 2 ....TPFA2-P01810-11 ..Control Handle Assembly ........ 180° ........1 ....P01816-11....Control Handle Assembly (TPFA-Z only)..90° ......... 1 3 ....TPFA2-P01811-00 ..Speed Control Knob/Black....... ø35.5 x ø29.9 x 19mm ..1 4 .... -
Page 16: Electrical Connections
9.0 Electrical Connections...
Need help?
Do you have a question about the TPFA-X and is the answer not in the manual?
Questions and answers