Dahua DH-TPC-PT8320A Quick Start Manual
  1. Manuals
  2. Brands
  3. Dahua Manuals
  4. Thermal cameras
  5. DH-TPC-PT8320A
  6. Quick start manual
Dahua DH-TPC-PT8320A Quick Start Manual

Dahua DH-TPC-PT8320A Quick Start Manual

Thermal high-speed hybrid ptz camera
Hide thumbs Also See for DH-TPC-PT8320A:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual
Thermal High-Speed Hybrid PTZ Camera
Quick Start Guide
Version 1.0.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DH-TPC-PT8320A and is the answer not in the manual?

Questions and answers

Related Manuals for Dahua DH-TPC-PT8320A

Summary of Contents for Dahua DH-TPC-PT8320A

  • Page 1 Thermal High-Speed Hybrid PTZ Camera Quick Start Guide Version 1.0.0...
  • Page 2 Welcome Thank you for purchasing our network cameras. This user’s manual is designed to be a reference tool for using your product. Please read the following safeguards and warnings carefully before you use this series product. Please keep this user’s manual well for future reference. Important Safeguards and Warnings Electrical safety ...
  • Page 3 Please contact after-sale service to replace desiccant when it becomes green.   It is recommended to use the device together with lightning arrester to improve lightning protection effect. It is recommended to get the grounding holes to be grounded to enhance the reliability of the ...

  • Page 4: Regulatory Information

    If there is any uncertainty or controversy, please refer to our final explanation.  Regulatory Information FCC Information 1.1 FCC conditions： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference ...

  • Page 5: Table Of Contents

    Table of Contents 1 Device Framework ..........................5 1.1 Device External Cable ........................5 1.2 Dimension ............................. 6 2 Device Installation ..........................8 2.1 Install Micro SD Card and Reset Device ..................8 2.2 Device Installation (Side Cable Exit) ..................... 9 2.3 Device Installation (Bottom Cable Exit) ..................

  • Page 6: Device Framework

    1 Device Framework 1.1 Device External Cable Note  The following structure figure is for reference only. It is only used to know the functions of cable ports.  There might be some minor differences between different devices, so please refer to the actual products you purchased.

  • Page 7: Dimension

    Port Port name Connector Function description Various Include alarm input and output, please I/O port external alarm refer to Table 1-2 for more details. devices Audio input Input audio signal, receive analog audio AUDIO IN port signal from pickup and other devices. Audio output Output audio signal to speaker and other AUDIO OUT...
  • Page 8 Refer to Figure 1-3 and Figure 1-4 for the device dimension and pole-mounted chassis respectively. The unit is mm. Figure 1-3 Figure 1-4...

  • Page 9: Device Installation

    2 Device Installation There are various types of brackets which can satisfy various scene application for PTZ, it takes pole-mounted bracket as an example to introduce the device operation. Note The following figures are for reference only, please refer to actual device for more details.

  • Page 10: Device Installation (Side Cable Exit)

    2.2 Device Installation (Side Cable Exit) Note The installation surface has to sustain the total weight of device and its installation structure, which is no less than 80kg. Figure 2-2 Step 1 Dig three mounting hole sites on the cement block according to the mounting holes, Make sure the size of hole diameter needs to be in accordance with expansion bolt, and there shall be no deviation for hole site.

  • Page 11: Device Installation (Bottom Cable Exit)

    Note It is recommended that the GND hole shall be connected to ground, which is to improve device reliability. Step 5 Install waterproof connector for network port, which is shown in Figure 2-3. Figure 2-3 Keep the convex groove outward and install the rubber ring into the network port, and keep the smaller hole of the rubber ring outward and install the fixing rubber ring into the main body of the waterproof connector.
  • Page 12 Figure 2-4 Use inner hex wrench to loosen three screws on the bottom. Open white plug of combination cable, loosen the connector of combination cable and bottom cover respectively, and then pull the cable for replacement. Install back three chassis screws and cover, and then lock them firmly. Caution It needs to make sure that the sealing gasket is located in the sealing slot, which is to avoid water leaking and causing damage to the device.
  • Page 13  Connect the corresponding power, video output, audio cable, RS485 control cable, alarm input and output terminal according to requirement, and then twine the cable connection location with insulated rubber tape to make it waterproof. Caution The video port is covered the heat shrink tube of high shrinking ratio. After the video connection, please heat the tube and wrap it with waterproof tape, including other video connection ports.

  • Page 14: Network Configuration

    3 Network Configuration The IP address of all the cameras is the same when leaving factory (default IP 192.168.1.108). To make the camera access to the network smoothly, please plan the available IP segment reasonably according to the actual network environment. 3.1 Modify IP Address The cameras which are accessed via wired network can acquire and modify the IP address through "Quick Configuration Tool".

  • Page 15: Login Web Interface

    Figure 3-2 Step 5 Set the mode as Static, and input the planned Start IP, Subnet Mask and Gateway. Note Set the mode as DHCP when there is DHCP server in the network, the device will automatically acquire IP address from the DHCP server. Step 6 Click OK to finish modification.
  • Page 16 Note The default username and password is admin and admin respectively, please modify the administrator password as soon as possible after you successfully logged in. Step 3 Click Login and the system will display the main interface, which is shown in Figure 3-4 Note Please install plug-in according to system prompt for the first login.

  • Page 17: Appendix Ⅰ Lightening Protection And Surge Protection

    4 Appendix Ⅰ Lightening Protection and Surge Protection This series speed dome adopts TVS lighting protection technology. It can effectively prevent damages from various pulse signals below 6000W, such as sudden lighting and surge. While maintaining your local electrical safety code, you still need to take necessary precaution measures when installing the speed dome in the outdoor environment.

Table of Contents