Table of Contents
Advertisement
HP 3100 v2 Switch Series
Layer 3—IP Routing
Configuration Guide
HP 3100-8 v2 SI Switch (JG221A)
HP 3100-16 v2 SI Switch (JG222A)
HP 3100-24 v2 SI Switch (JG223A)
HP 3100-8 v2 EI Switch (JD318B)
HP 3100-16 v2 EI Switch (JD319B)
HP 3100-24 v2 EI Switch (JD320B)
HP 3100-8-PoE v2 EI Switch (JD311B)
HP 3100-16-PoE v2 EI Switch (JD312B)
HP 3100-24-PoE v2 EI Switch (JD313B)
Part number: 5998-5993
Software version: Release 5203P05
Document version: 6W100-20140603
Advertisement
Table of Contents
Related Manuals for HP 3100-8 v2 SI
Summary of Contents for HP 3100-8 v2 SI
-
Page 1: Configuration Guide
HP 3100 v2 Switch Series Layer 3—IP Routing Configuration Guide HP 3100-8 v2 SI Switch (JG221A) HP 3100-16 v2 SI Switch (JG222A) HP 3100-24 v2 SI Switch (JG223A) HP 3100-8 v2 EI Switch (JD318B) HP 3100-16 v2 EI Switch (JD319B) - Page 2 The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
-
Page 3: Table Of Contents
Configuring an IPv6 static route ······································································································································ 7 Displaying and maintaining IPv6 static routes ··············································································································· 8 Support and other resources ······································································································································· 9 Contacting HP ··································································································································································· 9 Subscription service ················································································································································· 9 Related information ··························································································································································· 9 Documents ································································································································································· 9 ... -
Page 4: Ip Routing Basics
IP routing basics Overview IP routing directs the forwarding of IP packets on routers based on a routing table. This book focuses on unicast routing protocols. The term "router" in this chapter refers to both routers and Layer 3 switches. The types of interfaces that appear in any figures other than the network diagrams for configuration examples are for illustration only. -
Page 5: Routing Preference
A route entry includes the following key items: • Destination—IP address of the destination host or network. Mask—Mask length of the IP address. • Pre—Preference of the route. Among routes to the same destination, the one with the highest • preference is optimal. - Page 6 Task Command Remarks display ip routing-table ip-address [ mask Display information about routes to | mask-length ] [ longer-match ] Available in any view the specified destination. [ verbose ] [ | { begin | exclude | include } regular-expression ] display ip routing-table ip-address1 Display information about routes { mask | mask-length } ip-address2 { mask...
-
Page 7: Configuring Static Routing
Configuring static routing Introduction Static route Static routes are manually configured. If a network's topology is simple, you only need to configure static routes for the network to work properly. The proper configuration and usage of static routes can improve network performance and ensure bandwidth for important network applications. -
Page 8: Configuring A Static Route
Configuring a static route Before you configure a static route, complete the following tasks: • Configure the physical parameters for related interfaces. Configure the link-layer attributes for related interfaces. • Configure the IP addresses for related interfaces. • Follow these guidelines when you configure a static route: The next hop address cannot be the IP address of a local interface (such as a VLAN interface). - Page 9 Task Command Remarks Available in Delete all the static routes. delete static-routes all system view For more information about the display ip routing-table protocol static [ inactive | verbose ] [ | { begin | exclude | include } regular-expression ] command, see Layer 3—IP Routing Command Reference.
-
Page 10: Configuring Ipv6 Static Routing
Configuring IPv6 static routing Overview Static routes are manually configured. They work well in simple networks. Proper configuration and use can improve network performance and ensure enough bandwidth for important applications. Static routes cannot adapt to network topology changes. If a fault or a topological change occurs in the network, the network administrator has to modify the static routes manually. -
Page 11: Displaying And Maintaining Ipv6 Static Routes
Step Command Remarks Required ipv6 route-static ipv6-address prefix-length { interface-type interface-number The default Configure an IPv6 static route. [ next-hop-address ] | next-hop-address } preference of IPv6 [ preference preference-value ] static routes is 60. NOTE: If you specify a broadcast interface, such as a VLAN interface, as the output interface for a static route, you must specify the next hop address. -
Page 12: Support And Other Resources
Related information Documents To find related documents, browse to the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals For related documentation, navigate to the Networking section, and select a networking category. •... -
Page 13: Conventions
Conventions This section describes the conventions used in this documentation set. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic Italic text represents arguments that you replace with actual values. Square brackets enclose syntax choices (keywords or arguments) that are optional. Braces enclose a set of required syntax choices separated by vertical bars, from which { x | y | ... - Page 14 Network topology icons Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features.
-
Page 15: Index
Index C D I O R Introduction,4 IPv6 static routes features,7 Configuring a static route,5 Configuring an IPv6 static route,7 Contacting HP,9 Overview,1 Conventions,10 Overview,7 Default IPv6 route,7 Related information,9 Displaying and maintaining a routing table,2 Route backup,2 Displaying and maintaining IPv6 static...