Hilti SF121-A Operating Instructions Manual
Hide thumbs
Also See for SF121-A:
- Operating instructions manual (12 pages) ,
- Operating instructions manual (136 pages)
Advertisement
Table of Contents
- 1 Table of Contents
- 2 General Information
- 3 Technical Data
- 4 Electrical Safety
- 5 General Safety Rules
- 6 Functional Description
- 7 Specific Safety Rules and Symbols
- 8 Assembly
- 9 Care and Maintenance
- 10 Operation
- 11 Accessories
- 12 Disposal
- 13 Manufacturers Warranty - Tools
- Download this manual
See also:
Operating Instructions Manual
Advertisement
Table of Contents
Related Manuals for Hilti SF121-A
Summary of Contents for Hilti SF121-A
- Page 1 SF121-A Operating instructions 1–6 Mode d’emploi 7–12 Instrucciones de uso 13–18 Manual de instruções 19–24 Printed: 07.07.2013 | Doc-Nr: PUB / 5070600 / 000 / 00...
- Page 2 ETL listed to US and Canadian safety standards Homologué ETL (conforme aux normes de sécurité américaines et canadiennes) Producto homologado según normas de seguridad americanas y canadienses Produto homologado de accordo com as normas de segurança americanas e canadianas Printed: 07.07.2013 | Doc-Nr: PUB / 5070600 / 000 / 00...
- Page 3 STOP 1-15 Printed: 07.07.2013 | Doc-Nr: PUB / 5070600 / 000 / 00...
- Page 4 Printed: 07.07.2013 | Doc-Nr: PUB / 5070600 / 000 / 00...
-
Page 5: Table Of Contents
In these operating instructions, the word "tool" always refers to the SF121-A with battery. The following conditions must always be observed Operating controls and component parts when the tool is in use: –... -
Page 6: Technical Data
2. Technical data SF121-A battery drill driver Voltage: 12 Volt Drill driver weight incl. battery and chuck: 1.95 kg (4.32 lbs) Dimensions (l×h×w): 220×231×72 mm (8.7×9.1×2.8″) Speed (no load): 1st speed: 0–400 r.p.m. 2nd speed: 0–1300 r.p.m. ″) Chuck / Quick-release chuck capacity: 1.5–13 mm (... -
Page 7: General Safety Rules
3. General safety rules Avoid accidental starting. Be sure switch is in the locked or off position before inserting battery pack. Carrying tools with your finger on the switch or insert- ing the battery pack into a tool with the switch on invites 3.1 Warning! accidents. -
Page 8: Specific Safety Rules And Symbols
Maintain tools with care. Keep cutting tools sharp and from these exposures varies, depending on how often clean. you do this type of work. To reduce exposure to these Properly maintained insert tools with sharp cutting edge chemicals, the operator and bystanders should work are less likely to bind and are easier to control. -
Page 9: Assembly
Speed selection and observed before the tool is used. Two-speed switch The speed can be selected using the mechanical two- The SF121-A may be used only with the SFB121 speed switch, i.e. 1 speed: 0–400 r.p.m. or 2 speed: or SFB126 battery. -
Page 10: Accessories
The Hilti SFB121 battery has 10 nickel-cadmium cells. The Hilti SFB 126 battery has 10 nickel-metal hydrid cells. Both you and Hilti bear the responsibility for recycling of the worn-out batteries in keeping with environmental protection requirements. Important: Do not throw worn-out batteries into household waste, a fire or water. - Page 11 Tel.: +423 / 234 2111 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 2581 1109 10-Pos. 3 Printed in China © 2009 Right of technical and programme changes reserved S. E. & O.