Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for EdilKamin fLAMMA
Summary of Contents for EdilKamin fLAMMA
- Page 1 WOOD BOIler-stOve fLAMMA cs Installation, use and maintenance...
-
Page 2: Table Of Contents
305/2011 and the harmonized european standard eN 13240:2001 + A2:2004 + AC:2006 + AC:2007 WOOD stOves, trademark eDIlKAMIN, called FlAMMA /FlAMMA Cs 14 e 24 Year of manufacture: ref. Data nameplate FlAMMA /FlAMMA Cs 14 Declaration of Performance DoP eK n° : FlAMMA /FlAMMA Cs 24 Declaration of Performance DoP eK n°... -
Page 3: Introduction
If you lose it, you can request a copy or download it from • the declaration of conformity given to you by the installer. www.edilkamin.com the warranty conditions are given in the warranty certificate After unpacking the product, check the condition and accompanying the product. -
Page 4: Safety Information
• running it dry can damage it. DrY WOOD IN tHe FIrePlACe. You risk dirtying • Flamma is designed to operate in an open the product, fires in the chimney flue and causing expansion vessel circuit (if permitted by local damage to the environment. -
Page 5: Dimensions
GENERAL INFORMATION FlAMMA e FlAMMA Cs - internal dimensions of hearth cm 33 (l) x 34 (P) x 38 (H) thermal discharge valve (Flamma Cs) M without kit r without kit 7 4 11 5 F Ø 15 fumes discharge... -
Page 6: Technical Data
°C Minimum draught Fume flow capacity 18,3 13,4 * the heating volume is calculated with the heat request of 33 Kcal/m³ hour EDILKAMIN s.p.a. reserves the right to change the products at its discretion without notice. -
Page 7: Preparation And Packaging
AND UNpACKING CONTENTS OF DELIVERY the materials composing the packaging are not toxic the delivery consists (for both Flamma and Flamma or harmful, therefore no particular disposal processes Cs) of 2 packages: are required. • one containing the product’s frame (1);... - Page 8 pACKAGING to remove the product from the pallet: INSTALLING THE CERAMIC pANELS - remove the fastening screws (V) on the pallet on both sides of the stove the ceramics kit includes: - remove the stove from the pallet and pay particular • n.
-
Page 9: Installation
INSTALLATION to install the front panels (B and C), remove the front metal panel (E). Now fit the top (B) and bottom (C) front panels with the M4 bolts (M). the front panel (C) has a recess. Install it downwards to prevent interference with the door hinge. - Page 10 INSTALLATION INSTALLING THE OpTIONAL FAN KIT IF YOU DO NOT INSTALL THE the Flamma and Flamma Cs are designed for heating OpTIONAL FAN KIT, YOU MUST water and the room in which they are installed. OpEN THE pANEL (C) UNDER THE they heat the room by means of radiation and natural CERAMIC pANELS.
- Page 11 INSTALLATION EXTERNAL AIR INTAKE REMARKS ON INSTALLATION to re-integrate burnt oxygen during stove functioning, you need to have an installation premises suitable for Note that: the external air intake. • the appliance may only be installed by a qualified In general, we suggest two ways for ensuring a proper technician authorised to issue the declaration of flow of combustion air.
- Page 12 INSTALLATION CHIMNEY SYSTEM THE SMOKE CHANNEL (Smoke channel, chimney flue and chim- • if in metal must have a CE marking (EN 1856-2) or ney stack) similar national law; this chapter is drafted according to the european • cannot be in flexible metal material standards eN 13384, eN 1443, eN 1856, eN 1457. • to check the flow, a shutter is advised for draft over the installation technicians must take into considera- 25 Pa tion these and any other local standards.
- Page 13 INSTALLING THE WATER CIRCUIT Never light the fire in the hearth (even to test it) when the circuit is dry (no water); doing so Flamma is designed to install to a water circuit with can irreparably damage the appliance. open expansion vessel.
- Page 14 (vst - provided by to the appliance itself. edilkamin) must be connected to the cooling circuit • the safety line to the expansion vessel must be (Al) with a pressure of at least 1.5 bar.
- Page 15 INSTALLATION OpTIONAL INTERNAL WATER CIRCUIT KITS (R, RW, R2, RW2 WITH WATER CIRCUIT ADApTER KIT) For simple installation, edilkamin offers pre-assembled Domestic hot water will only be produced kits for installation inside the product. when the product is hot. the product you require depends on the type of circuit As water is heated, pressure in the you are installing.
-
Page 16: Instructions For Use
• possible irreversible changes to the colour of the paint on the metal parts for which edilkamin or the retailer cannot be held liable. to respect the environment and safety, do NOt burn, among other things: plastic, varnished wood, coal and bark waste. - Page 17 ISTRUCTIONS FOR USE FIRST SWITCH ON pHASES Lighting a cold fireplace • ensure you have read and understood the content 1. Check the existing ash bed is not too high. If the of this manual ash bed is too high, there is a danger of opening the • remove all the inflammable parts from the product door of the fireplace to add wood and possible brazier (manuals, labels, etc.).
-
Page 18: Maintenance
MAINTENANCE Before doing any maintenance, disconnect ATTENTION! the appliance from the mains. All the cleaning operations of all the parts should be carried out with the stove com- Regular maintenance essential pletely cooled. keeping the appliance in good working Cleaning the glass order. - Page 19 DISpOSAL At the end of its service life, dispose of the product as required by regulations. the refractory deflector is subject to wear. Neither your reseller nor edilkamin are liable for breakage, whether accidental or due to wear.
-
Page 20: In The Event Of Problems
• use of fuel other than that recommended the seals of the fireplace are intact: the door of the fireplace is closed properly. edilkamin or the retailer cannot be held liable for damage caused as described above 3) If the glass gets dirty quickly, check if: The wood used is dry. - Page 24 *941299-GB* w w w . e d i l k a m i n . c o m cod. 941299-GB 10.16/B...
Need help?
Do you have a question about the fLAMMA and is the answer not in the manual?
Questions and answers