English Contents Dear Customer, KombiSystem Guide to Using this Manual Thank you for choosing a quality engineered STIHL product. Safety Precautions and Working Techniques It has been built using modern Approved KombiTools production techniques and comprehensive quality assurance. Mounting the Loop Handle...
Manual fuel pump In the STIHL KombiSystem a number of Therefore, some changes, modifications different KombiEngines and KombiTools and improvements may not be covered can be combined to produce a power in this manual.
Working Techniques and its operation – do not lend of rent power tool by STIHL or are technically your power tool without the identical. It is important that you read the Special safety precau- KombiEngine and KombiTool instruction chapter on "Approved KombiTools".
Page 6
English Transporting the Power Tool Smooth action of choke knob, After fueling, tighten – throttle trigger lockout and throttle down the fuel tank cap as trigger – the throttle trigger must securely as possible. return automatically to the idle position. The choke knob must spring back from the g position to This reduces the risk of unit vibrations the run position F when the throttle...
Page 7
Make sure you always have good make proper adjustments or repairs. caused by an excessively high balance and secure footing. STIHL recommends an authorized concentration of exhaust gases in the STIHL servicing dealer. work area. Be particularly alert and cautious when...
Page 8
Use only a spark plug of the type are working properly. Do not continue approved by STIHL and make sure it is Maintenance and Repairs operating your power tool if it is in good condition – see "Specifications".
English Approved KombiTools The following STIHL KombiTools may be mounted on the KombiEngine: FS-KM FS-KM KombiTool Application FS-KM Trimmer with mow- ing head FS-KM Trimmer with grass cutting blade FSB-KM Trimmer with mow- FH-KM ing head FSB-KM HT-KM BG-KM HL-KM 135°...
English Adjusting and Securing the Loop Handle Mounting the Loop Handle A barrier bar is supplied with the machine. Fit the barrier bar on the loop handle. Place the clamp (3) in the loop handle (4) and position them both against the drive tube (5).
Use only high-quality two-stroke engine STIHL MotoMix uses STIHL HP Ultra location protected from light and the sun. oil – preferably STIHL HP, HP Super or two-stroke engine oil for an extra long Fuel mix ages – only mix sufficient fuel HP Ultra, which are specially formulated engine life.
Take care not to spill fuel while fueling and do not overfill the tank. Place the machine on level ground STIHL recommends you use the STIHL so that the filler cap is facing up. filler nozzle for fuel (special accessory).
English is released: The ignition is switched on Starting the Engine Starting / Stopping the again after the engine stops – the engine Engine is then ready to start. Function of throttle set wheel Controls Press the manual fuel pump bulb (5) at least five times –...
Page 14
English Cranking Hold the starter grip with your right Depress throttle trigger lockout and hand. pull the throttle trigger – the choke Place the power tool on the ground knob moves to the Run F position. Pull the starter grip slowly and so that it rests on the machine steadily.
English Running engine stalls in cold start Operating Instructions Replacing the Air Filter position g or under acceleration. Continue cranking in position F until Do not remove the filter cover or replace the engine runs. During break-in period the air filter as long as there is no If the engine does not start noticeable loss of power.
Fit a new spark plug after about 100 operating hours – or sooner if the electrodes are badly eroded. Install only suppressed spark plugs of the type approved by STIHL – see "Specifications". Clean dirty spark plug. The carburetor has been set at the...
If the engine speed increases or if the cutting attachment rotates, the throttle cable has to be adjusted. Shut off the engine. Have throttle cable adjusted by your dealer. STIHL recommends an authorized STIHL servicing dealer. KM 94 RC...
English Antivibration Element Inspections and Maintenance by Dealer Maintenance Work STIHL recommends that you have servicing and repair work carried out exclusively by an authorized STIHL servicing dealer. Fuel Pickup Body in Tank A vibration-absorbing rubber element is installed between the powerhead and the drive tube.
English Maintenance and Care The following intervals apply to normal operating conditions only. If your daily work- ing time is longer or operating conditions are difficult (very dusty work area, etc.), shorten the specified intervals accordingly. Visual inspection (condition, leaks) Complete machine Clean Replace any damaged parts...
Page 20
Anti-vibration elements Have replaced by servicing dealer Safety labels Replace Only if there is a noticeable loss of engine power STIHL recommends an authorized STIHL servicing dealer. see chapter "Inspections and Maintenance by Dealer", section "Antivibration Elements" KM 94 RC...
English servicing dealer. STIHL dealers are Minimize Wear and Avoid regularly given the opportunity to attend Damage training courses and are supplied with the necessary technical information. Observing the instructions in this manual helps reduce the risk of unnecessary If these maintenance operations are not wear and damage to the power tool.
English Main Parts Manual fuel pump Choke knob Carburetor adjusting screw Tank cap Fuel tank Starter grip Muffler Throttle trigger Adjusting wheel 10 Stop switch 11 Throttle trigger lockout 12 Carrying ring 13 Loop handle 14 Barrier bar 15 Coupling sleeve 16 Wing screw 17 Spark plug boot with cap 18 Air filter cover...
For information on compliance with the FS-KM, FSB-KM and HT-KM 1 to 1 REACH regulation (EC) No. 1907/2006 HL-KM 1 to 4 Spark plug (resistor see www.stihl.com/reach. BF-KM, KB-KM, KW-KM, type): NGK CMR 6 H BG-KM and SP-KM 1 to 6 Electrode gap: 0.5 mm...
Take the product, replacement parts which have been accessories and packaging to an conforms to the relevant requirements of approved by STIHL for this power tool or approved disposal site for environment- the Directives 2006/42/EC and are technically identical. Only use high- friendly recycling.
Page 25
English Done at Waiblingen, 11.03.2016 ANDREAS STIHL AG & Co. KG Thomas Elsner Director Product Management and Services KM 94 RC...
Need help?
Do you have a question about the KM 94 R and is the answer not in the manual?
Questions and answers