Related Manuals for Rigol DS1000B Series
Summary of Contents for Rigol DS1000B Series
- Page 1 Quick Guide RIGOL Publication number QGA04113-1110 Aug. 2011 DS1000B Series Digital Oscilloscope DS1074B, DS1104B, DS1204B © 2008 RIGOL Technologies, Inc. All Rights Reserved...
- Page 3 P.R. China. Information in this publication replaces all previous corresponding material. RIGOL reserves the right to modify or change part of or all the specifications and pricing policies at company’s sole decision. NOTE: RIGOL is registered trademark of RIGOL Technologies, Inc.
- Page 4 Use Proper Fuse. Use the fuse of the type, voltage and current ratings as specified for the instrument. Avoid Circuit or Wire Exposure. Do not touch exposed connections and components when power is on. © 2008 RIGOL Technologies, Inc. Quick Guide for DS1000B Series...
- Page 5 A in the standard of EN 61326: 1997+A1+A2+A3, but can’t meet the limit values of B. Measurement Category The DS1000B series Digital Oscilloscope is intended to be used for measurements in Measurement Category I. Measurement Category Definitions Measurement Category I is for measurements performed on circuits not directly connected to MAINS.
- Page 6 CAUTION indicates that a potential damage to the instrument or other property might occur. Symbols on the Product. These symbols may appear on the product: Hazardous Refer to Protective Chassis Earth Voltage Instructions Earth Ground Ground Terminal © 2008 RIGOL Technologies, Inc. Quick Guide for DS1000B Series...
-
Page 7: Table Of Contents
RIGOL Contents Necessary Inspection 1 How to Connect Power Cord 4 How to Connect Probe or BNC 5 How to Connect USB Devices 7 Troubleshooting 8 Contact RIGOL 10 © 2008 RIGOL Technologies, Inc. Quick Guide for DS1000B Series... -
Page 9: Necessary Inspection
In case there is any mechanical damage or defect, notify the RIGOL Sales Representative. If the shipping container is damaged, or the cushioning materials show signs of stress, notify the carrier as well as the RIGOL sales office. Keep the shipping materials for the carrier’s inspection. 3． Check the accessories. - Page 10 RIGOL I. Front Panel of the instrument DS1000B Series Front Panel II. Standard accessory A Power Cord Four Passive Probes A USB Cable A CD-ROM* © 2008 RIGOL Technologies, Inc. Quick Guide for DS1000B Series...
- Page 11 RIGOL A Quick Guide A Warranty Card NOTE*: The CD-ROM includes《User’s Guide》and Application Software. III. Optional accessories BNC Cable USB-GPIB Adapter Instrument Carrying Case © 2008 RIGOL Technologies, Inc. Quick Guide for DS1000B Series...
-
Page 12: How To Connect Power Cord
User’ Guide to change the fuse if needed. (4) After the above inspections, the power key on the front pannel is still not lit, please contact RIGOL for help. © 2008 RIGOL Technologies, Inc. Quick Guide for DS1000B Series... -
Page 13: How To Connect Probe Or Bnc
If your probe is a new one, or if it is the first time you connect to the oscilloscope, before use it, please do the following compensation operation: © 2008 RIGOL Technologies, Inc. Quick Guide for DS1000B Series... - Page 14 2． Connect the BNC As shown in the following figure, insert the the BNC cable to the BNC conector on the front pannel, rotate clockwise to lock the BNC. BNC Connecting Instruction © 2008 RIGOL Technologies, Inc. Quick Guide for DS1000B Series...
-
Page 15: How To Connect Usb Devices
RIGOL How to Connect USB Devices DS1000B series oscilloscope support the USB flash drive and connections to PC or printer throught USB. The instrument provides two USB Hosts and a USB Device. Connect USB Host (Front Panel) Connect USB Host (Rear Panel) Connect USB Device(Rear Panel) ©... -
Page 16: Troubleshooting
(1) Check the power cord connection. (2) Ensure the power switch is turned on. (3) After the above inspection, restart the oscilloscope. (4) If the problem still remains, please contact RIGOL for help. 2. After the signal acquisition the waveform does not appear: (1) Check the probes connected with the signals. - Page 17 (2) If connecting to a PictBridge printer or the printing is unsuccessful, maybe the USB Device menu has been set to be “Computer”, you should switch it to “Auto Detect” or “PictBridge”. If necessary, restart the oscilloscope. © 2008 RIGOL Technologies, Inc. Quick Guide for DS1000B Series...
-
Page 18: Contact Rigol
RIGOL Contact RIGOL If you have any problem or requirement when using our products, please contact RIGOL Technologies, Inc. or your local distributors, or visit: www.rigol.com © 2008 RIGOL Technologies, Inc. Quick Guide for DS1000B Series...