Option Settings - Philips TPM14.1L Service Manual

Picture mode Screen size
Warm (6500K) 24PHG4109/77 99
28PHG4109/77 117
32PFG4109/77 123
32PFG4109/78 122
32PHG4109/77 125
32PHG4109/78 124
39PFG4109/77 128
39PFG4109/78 125
40PFG4109/78 128
47PFG4109/77 128
47PFG4109/78 126
50PFG4109/77 121
50PFG4109/78 128
This group setting of colour temperature will be applied
automatically to the TV / VGA / HDMI / AV sources.
6.4

Option Settings

6.4.1 Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
MT5561 ICs is made known by the option codes.
Notes:
• After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE and press OK on the RC.
• The new option setting is only active after the TV is
switched "off" / "stand-by" and "on" again with the mains
switch (the NVM is then read again).
6.4.2 Option Code Overview
Enter SAM mode to check the option codes. they could be
edited in the NVM.
6.4.3 Display Code Overview
Press the following key sequence on a standard RC
transmitter: "062598" directly followed by MENU and "xxx",
where "xxx" is a 3 digit decimal value of the panel type: see
column "Display Code" in
Code, restart the set immediately.
Table 6-3 Display code overview
CTN_ALT BOM#
24PHG4109/77
24PHG4109/77
28PHG4109/77
32PFG4109/77
32PFG4109/78
32PHG4109/77
32PHG4109/78
39PFG4109/77
39PFG4109/77
39PFG4109/78
39PFG4109/78
40PFG4109/78
47PFG4109/77
47PFG4109/78
50PFG4109/77
50PFG4109/78
Colour temperature
Red Green
103
120
85
84
84
82
91
90
110
111
109
105
110
Table 6-3. After resetting the Display
Panel Type Display Code
TPM236H3-BJ1L02 157
TPM236H3-BJ1L03 164
TPT275B5-A014 158
TPT315B5-EUJFFA 154
TPT315B5-EUJFFA 154
TPT315B5-DXJSFE 151
TPT315B5-DXJSFE 151
TPT390J1-HJ1L02 153
TPT390J1-HVN04 165
TPT390J1-HJ1L02 153
TPT390J1-HVN04 165
TPT400LA-HM06 160
TPT470H1-DUJFFE 155
TPT470H1-DUJFFE 155
TPT500J1-HVN04 159
TPT500J1-HVN04 159
Alignments
6.5 Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
Blue
repair shop (SSB repair on component level) implies the reset
124
of the NVM on the SSB.
79
A repaired SSB in Service should get the service Set type
76
"00PF0000000000" and Production code "00000000000000".
75
Also the virgin bit is to be set. To set all this, you can use the
73
ComPair tool or use the "NVM editor" and "Dealer options"
70
items in SAM (do not forget to "store").
48
45
After a repaired SSB has been mounted in the set (set repair
108
on board level), the type number (CTN) and production code of
109
the TV has to be set according to the type plate of the set. For
106
this, you can use the NVM editor in SAM. The loading of the
50
CTN and production code can also be done via ComPair
53
(Model number programming).
In case of a display replacement, reset the "Operation hours
display" to "0", or to the operation hours of the replacement
display.
Remark:
- After the NVM has been replaced, go to SAM and scroll to the
<Reload MAC address> (see figure 1*).
- Select the item and press <OK> on the RC.
2
C
6.5.1 Reset of Repaired SSB
Instruction
After NVM replacement, reload MAC address via SAM
menu.This ensures the correct MAC address to be available in
CSM for future repair actions.
Way of working:
• After the NVM has been replaced, go to SAM and scroll to
the <Reload MAC address> .
• Select the item and press <OK> on the RC.
Notes:
• Only applicable to all related models that are "Smart TV
level 0"enabled (only YouTube access). For models
without internet connection feature, no action is needed.
• HDCP keys are located in the NVM. If you are loading NVM
with the ComPair tool, there is warning message displayed.
New NVM EEPROMs are shipped with pre-loaded HDCP keys.
6.5.2 SSB Identification
SSB's of this chassis are identified by a "715" code on the SSB.
715Axxxx-Nnn-MMM-OOOO
• 715 main category, Printed Wiring Board
• Axxxx sub category, sequential coding number
• Nnn Version code
•
•
• MMM Mounting variation code
• OOOO Optional variation code
Make sure when replacing an SSB the SSB identification codes
match the replacement panel.
6.6 Cable position numbers
In this chassis, the cable position numbers can be defined via
the rule that the number is always starting with an "E" followed
by the connector number of the current sourcing board. The
order is always seen from where the power initiates from. So
from PSU to SSB, from SSB to IR/LED panel, from IR/LED
panel to keyboard control panel. For example, a cable from the
PSU connector CN902 to the SSB connector CN701, will have
the position number ECN902.
back to
div. table
TPM14.1L LA
N Development number
nn Production number
6. EN 31
2014-Mar-07