All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JH 667 TV Service...
At the moment of writing, not all Altitude : 0 to 40000 feet ( non operating ) information was available (only the 26-inch TPE1.1U LA Air pressure : 600 to 1100 ( non operating ) model was available). As soon as the other models are introduced, an update manual will be released.
Page 3
TPE1.1U LA 1. Technical Specifications and Connections 1.2.2.1.2 Headphone output : Audio: R/L output 10mW at 32 . 3.5mm stereo jack with switch Impedance is between 8 and 600 . 1.2.2 Allowed signal mode specified 1.2.2.1 TV system signal mode: RF support: NAFTA: NTSC(M,N) and ATSC (8VSB and QAM) Video1,2,3 / S-video1,2: Support, NTSC colour system.
TPE1.1U LA 2. Safety Instructions, Warnings and Notes 2. Safety Instructions, Warnings and Notes index of this chapter: the parts lists, are interchangeable per position with the 2.1 Safety Instructions semiconductors in the unit, irrespective of the type 2.2 Warnings indication on these semiconductors.
Page 5
In case of doubt whether the board is lead-free or not (or with mixed technologies), you can use the following method: · Philips CE is going to produce lead-free sets (PBF) from Always use the highest temperature to solder, when using 1.1.2005 onwards.
TPE1.1U LA 3. Directions for Use 3. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com...
TPE1.1U LA 4. Mechanical Instructions 4. Mechanical Instructions Index of this chapter: 4.1 Assy/Panel Removal 4.2 Set Re-assembly 4.1 Assy/Panel Removal Front view Fig.10 Fig.9 Step 2. Remove the Back cover and Main shield assy as Fig.11~18. Remove the 7 screws and the other 2 screws on the sides as Fig.11...
Page 8
TPE1.1U LA 4. Mechanical Instructions Fig. 16 Fig. 22 Fig. 17 Fig. 23 Fig. 18 Step 3. Remove the Scaler, Power,IR, Key Control, Side AV and USB board. Fig. 24 Remove the 14 screws and disconnect the 12 cables as Fig. 19 .
TPE1.1U LA 5. Service Modes, Error Codes and Fault Finding 5. Service Modes, Error Codes and Fault Finding Smart modes. index of this chapter: Auto store of personal presets. 5.1 Test Points Auto user menu time-out. 5.2 Service Modes 5.3 Stepwise Start-up How to Activate SDM 5.4 ComPair...
Page 10
TPE1.1U LA 5. Service Modes, Error Codes and Fault Finding error is displayed. If there are multiple errors in the buffer, which are or he can decide if it is necessary to visit the customer. not all generated by a single module, there is probably another The CSM is a read only mode;...
Page 11
· V-Chip Movie Status . Indicates the setting of the V-chip ComPair (Computer Aided Repair) is a service tool for Philips as applied by the selected TV channel. Same values can Consumer Electronics products. ComPair is a further be shown as for MOVIE RATINGS LOCK .
Page 12
TPE1.1U LA 5. Service Modes, Error Codes and Fault Finding access the I C/UART bus of the television. ComPair can When multiple errors occur (errors occurred within a short time send and receive I C/UART commands to the micro span), there is a high probability that there is some relation controller of the television.
Page 13
TPE1.1U LA 5. Service Modes, Error Codes and Fault Finding visible via the front LED. This is especially useful for fault There is one hardware protection in this chassis: Audio DC " finding, when there is no picture. Protection ".This protection occurs when there is a DC voltage on the speakers.
Page 14
Disconnect the TV from the Mains/AC Power. standalone set, without the need of an E-JTAG debugger. A · Press the OK button on a Philips DVD RC-6 remote " " description on how to upgrade the main software can be found control (it is also possible to use the TV remote in DVD mode).
Page 15
TPE1.1U LA 5. Service Modes, Error Codes and Fault Finding 5.9.4 Stand-by Software Upgrade It will be possible to upgrade the Stand-by software via a PC and the ComPair interface. Check paragraph ComPair on " " how to connect the interface. To upgrade the Stand-by software, use the following steps: 1.
TPE1.1U LA 6. Block Diagram PCB architecture Control Board Main BOARD LCD Panel Base on TV 510 just to 26"/27"/32" modify Inverter SMPS board board .DC-DC power .200W max Vcc, .Audio Amp Bright_ADJ .PFC .inverter and panel Inverter ON_OFF .<1W at STBY...
Page 18
TPE1.1U LA 6. Block Diagram RESET PNX2015 PNX2015 Control Control Ext Reset Reset-PNX2015 Reset- FE-Main PNX2015 PNX2015 2004 2004 Reset-system Reset- Stby (5V2 dip) 8852 Stby uP Reset- Stby uP 8852 audio HP/Power Amp Reset- MIPS Anti-Plop 3V3-Standby EEPROM EEPROM...
Page 20
TPE1.1U LA 6. Block Diagram Function block of Power Board AC input AC input PFC correction PFC correction LCI filter LCI filter 90-264V 90-264V DC 400V DC 400V L6562 L6562 Fly-back topology Fly-back topology DC+16V DC+16V Main Board Main Board...
Audio: R/L output - 10mW at 32W. 3.5mm stereo jack with switch 8.1 Electrical Instructions&Serial NO. Definition Impedance is between 8 and 600W. 2.1.3 SPDIF Output (Sony Philips Digital Interface Format) General points Level: - +/-0.5V square wave During the test and measuring, supply a distortion free AC mains 2.1.4 DVD player output...
Page 74
TPE1.1U LA 8. Alignments Power supply Item 1920X1080i 1280X720P 720X480P 720X480i 60Hz 60Hz 60Hz 60Hz Setup the AC Input at 110VAC, and power board provide two DC Pixel rate 74.25MHz 74.25MHz 27.027MHz 13.5MHz Output (13.468 ns) (13.468 ns) (37.000 ns) ( 74.074 ns )
Page 75
TPE1.1U LA 8. Alignments Video repro 2. Check the gray pattern should be distinguished and color bar is correct Comb filter: 3D comb Note: 1. Use Minolta CA-110 for color coordinates and Ambient light: Off luminance check. MOP: Off 2. Luminance> 400 cd/m...
Page 76
TPE1.1U LA 8. Alignments Contrast Personal Contrast Brightness Brightness Color Color Sharpness Sharpness Color temperature Normal Color temperature Normal Tint Tint Picture format Automatic Picture format Automatic Rich Contrast b).Smart Sound : Speech (default) Brightness SOUND VOLUME : 15 Color...
Page 77
TPE1.1U LA 8. Alignments c) .Features EQ BAND1 120Hz Personal Closed Captions : Off EQ BAND2 500Hz Sleeptimer :0 EQ BAND3 1.5KHz 7.3 Setup: EQ BAND4 5KHz Preferences EQ BAND5 10KHz Picture/sound preferences Speech Auto surround: On EQ BAND1 120Hz...
Page 78
TPE1.1U LA 8. Alignments 8.2 Software Updrade With Portable Memory Automatic software upgrade procedure 1. Power off your TV and remove all memory devices. 2. Insert the USB portable memory (not supplied) that contains the Introduction downloaded software upgrade. Magnavox offers software upgrade capability for your TV using 3.
Page 79
TPE1.1U LA 8. Alignments 8.3 Update DVD firmware for DVD Update DVD firmware for FL2/DVD 26" & 32" procedures 1. Burn one CD-R or CD-RW with two DVD rom images After burning finish, insert CD-R or CD-RW into FL2/DVD set.
TPE1.1U LA 9. Trouble Shooting 9. Trouble Shooting Index of this chapter 9.1 Trouble shooting 9.2 Circuit Description 9.3 IC Data Sheets 9.4 Repair Flow Chart 9.1 Trouble Shooting Trouble Shooting Tips- TV Symptoms Items to Check and Actions to follow ·...
Page 81
TPE1.1U LA 9. Trouble Shooting Trouble Shooting Tips- DVD Symptoms Items to Check and Actions to follow · No picture Refer to your TV s manual for correct Video In channel selection. Change the TV channel until you see the DVD screen.
Page 82
TPE1.1U LA 9. Trouble Shooting 9.2 Circuit Description General Description This LCD TV monitor using FL-2 platform. It can support TV signal. It's output resolution is up to 1366X768 75Hz for WXGA panel. It can support NTSC from RF, AV0, AV1, AV2 (CVBS and Y/C), YPbPr and RGB, HDMI (DVI via HDMI) , and also have side I/O , support CVBS/YC and Headphone for User easy used .
Page 83
TPE1.1U LA 9. Trouble Shooting Sound: PNX3000,PNX2015,PNX8550 Picture Improvement Path Chroma Key Chroma Horizontal Pexel Fetch CLUT & DCTI Sample-Rate Up-sample Unit Undither Up-convertor Filter Video/Gfx Luma Layer& Histogram Linear Colour Contrast& Sharpening Fetch Modification Features Interpolator Brightness Unit Control...
Page 84
TPE1.1U LA 9. Trouble Shooting 9.3 IC Data Sheets 9.3.1 IC Data Sheets-uPC3218GV(7T13) 9.3.2 IC Data Sheets-TPA3005D2(7901)
Page 86
TPE1.1U LA 9. Trouble Shooting 9.3.3 IC Data Sheets-TS482(7A04) 9.3.4 IC Data Sheets-TDA9970A(7B50)
Page 87
TPE1.1U LA 9. Trouble Shooting 9.3.5 IC Data Sheets-M24C02(7B02) DIP, SO and TSSOP Connections Logic Diagram 9.3.6 IC Data Sheets-M24C64(7P14) Logic Diagram DIP, SO, TSSOP and UFDFPN Connections 9.3.7 IC Data Sheets-TC58DVM82F1(7P80) PIN ASSIGNMENT BLOCK DIAGRAM...
Page 88
TPE1.1U LA 9. Trouble Shooting 9.3.8 IC Data Sheets-LM324(7A05) PIN CONFIGURATION EQUIVALENT CIRCUIT 9.3.9 IC Data Sheets-L5972(7004) PIN CONNECTION TEST APPLICATION CIRCUIT 9.3.10 IC Data Sheets-NCP5422A(7U00) PIN CONNECTIONS Application Diagram 9.3.11 IC Data Sheets-NTX2004(7T22) PIN ASSIGNMENTS AND DESCRIPTIONS...
Page 89
TPE1.1U LA 9. Trouble Shooting 9.3.12 IC Data Sheets-PNX2015(7J00) Block diagram...
Page 91
TPE1.1U LA 9. Trouble Shooting Pin configuration...
Page 92
TPE1.1U LA 9. Trouble Shooting 9.3.13 IC Data Sheets-PNX3000(7A00) Block diagram...
Page 93
TPE1.1U LA 9. Trouble Shooting Pin Configuration 9.3.14 IC Data Sheets-PNX8552(7V00) Block Diagram...
Page 94
TPE1.1U LA 9. Trouble Shooting Pin Configuration...
Page 95
TPE1.1U LA 9. Trouble Shooting 9.4 Repair Flow Chart 1.No work/LED is off 3.No picture/LED is green Check if power switch is Replace Power switch Check normal power board 1088, Check power board pin1~5=24V,pin6= 2.6V pin7=6.1V Check power board 1089...
Page 96
TPE1.1U LA 9. Trouble Shooting 4.No TV sound 7.LED and function key poor Check circuit around Check if control board and cable tuner 1T04 pin12 Replace 1T04 between control board output IF and scaler board signal Check 7A11 8.No HDMI picture...
Page 99
TPE1.1U LA 10.Spare Parts List 2U16 222278015663 CER2 0805 X7R 16V 1U PM10 3A18 232270570181 RST SM 0402 RC31 180R PM5 3H52 232270675601 RST SM 0402 RC32 560R PM1 2U17 222278413681 CER2 1812 X5R 16V 22U PM10 3A19 232270570181 RST SM 0402 RC31 180R PM5...
Page 100
TPE1.1U LA 10.Spare Parts List 3P86 232270570101 RST SM 0402 RC31 100R PM5 3L39 232270671002 RST SM 0402 RC32 1K PM1 3LG3 232270570101 RST SM 0402 RC31 100R PM5 3L40 232270570339 RST SM 0402 RC31 33R PM5 3LG5 232270570101 RST SM 0402 RC31 100R PM5...
Page 101
TPE1.1U LA 10.Spare Parts List 3U18 232270570221 RST SM 0402 RC31 220R PM5 5805 242253595853 IND FXD SM 0603 0U10 PM10 6A11 934054945115 DIO SIG SM BAS316 (PHSE) 3U19 232270570223 RST SM 0402 RC31 22K PM5 5806 242253595853 IND FXD SM 0603 0U10 PM10...
Page 102
TPE1.1U LA 10.Spare Parts List 3623 232270260279 RST SM 0603 RC21 27R PM5 7U13 934042530115 TRA SIG SM BC847BPN (PHSE) 3084 213811201222 RST SM 0805 RC05 2K2 PM5 7U15 934042520115 TRA SIG SM BC847BS (PHSE) 3085 213811201102 RST SM 0805 RC05...
TPE1.1U LA 11.Different Parts List Diversity of 32MD251D/37 compared with 26MD251D/37 Item 12NC Description 863900017157 32MD251D/37 0030 313815760771 FRONT BEZEL ASSY 0031 313815415061 BEZEL 0040 313815761471 BACK COVER ASSY 0041 313815417471 BACK COVER 0042 313815418421 VESA RUBBER 0100 313815417461 CAP...