Pioneer PDP-5000EX Service Manual page 7

5
Mode transition and structure of layers in Service Factory mode
Mode transition in Service Factory mode
Up
• To shift to another mode, press [MUTING].
• To shift to another item in a specific mode,
• To shift to the next nested layer below for an
Down
INFORMATION mode
1. VERSION (1)
2. MAIN NG
3. TEMPERATURE
4. HOUR METER
5. HDMI SIGNAL INFO1
6. HDMI SIGNAL INFO2
7. VDEC SIGNAL INFO
PANEL FACTORY mode
1. PANEL INFORMATION
2. PANEL WORKS
3. POWER DOWN
4. SHUT DOWN
5. PANEL-1 ADJ
6. PANEL-2 ADJ
7. PANEL REVICE
8. ETC.
9. RASTER MASK SETUP
10. PATTEN MASK SETUP
11. COMBI MASK SETUP
Structure of Layers in Panel Factory Mode 1
1. PANEL INFORMATION Version indication of the panel
2. PANEL WORKS Indications of the accumulated power-on time, pulse-meter
count, and power-on count of the panel
3. POWER DOWN Indication of the Power-down history
4. SHUT DOWN Indication of the Shutdown history
5. PANEL-1 ADJ (+)
1. X-SUS B
2. Y-SUS B
3. Y-SUSTAIL T1
4. Y-SUSTAIL T2 Modification not required because these items are basically
5. Y-SUSTAIL W for factory presetting
6. XY-RST W1
7. XY-RST W2
8. VOL SUS
9. VOL OFFSET Settings required after replacement of the panel
10. VOL RST P
11. SUS FREQ. For AM noise prevention (Depending on the mode,
brightness of the screen changes.)
6. PANEL-2 ADJ (+)
1. R-HIGH
2. G-HIGH
3 .B-HIGH Parameters for the WB adjustment of the panel, which are
4. R-LOW required during adjustment after panel replacement
5. G-LOW
6. B-LOW
7. ABL Setting of the power consumption. A setting table is
available for each vertical signal.
To "Structure of Layers in Panel Factory Mode 2"
5
6
PDP-5000EX Quick Reference upon Service Visit 2
press [»] or [«].
item with a "(+)" indication, press [ENTER].
To return to the next nested layer above,
also press [ENTER].
INITIALIZE mode
1. SYNC DET
2. SG MODE
3. SG PATTERN
4. SIDE MASK LEVEL
5. FINAL SETUP
6. HDMI INTR POSITION
6
7
Structure of Layers in Service Factory Mode
INFORMATION mode
1. VERSION (1)
2. MAIN NG
2-1.CLEAR
3. TEMPERATURE
4. HOUR METER
5. HDMI SIGNAL INFO 1
6. HDMI SIGNAL INFO 2
7. VDEC SIGNAL INFO
PANEL FACTORY mode
INITIALIZE
1. SYNC DET (+)
2. SG MODE
3. SG PATTERN SG
4. SIDE MASK LEVEL (+)
4-1. R MASK LEVEL
4-2. G MASK LEVEL
4-3. B MASK LEVEL
5. FINAL SETUP
5-1. DATA RESET
6. HDMI INTER POSITION (+) Items for use by engineers
Structure of Layers in Panel Factory Mode 2
7. PANEL REVISE(+)
R-LEVEL
G-LEVEL
B-LEVEL
8. ETC(+)
1. BACKUP DATA
2. DIGITAL EEPROM
3. PD INFO.
4. SD INFO.
5. HR-MTR INFO.
6. PM/B1-B5
7. P COUNT INFO.
8. MAX TEMP.
9. RASTER MASK SETUP (+)
1. MASK OFF
2. RST MASK 01
• • • • •
25. RST MASK 24
10. PATTEN MASK SETUP (+)
1. MASK OFF
2. PTN MASK 01
• • • • •
40. PTN MASK 39
11. COMBI MASK SETUP (+)
1. MASK OFF
2. CMB MASK 01
• • • • •
11. CMB MASK 10
PDP-5000EX
7
8
Version indications for the main system and panel system
Shutdown history for the main system (To shift to the
CLEAR layer, press [SET].)
To clear data, select "YES", using [|] or [\], then hold
[SET] pressed for several seconds.
Indications of converted temperature values for
temperature sensors 1 and 2 and fan operation
Indications of the accumulated power-on time and
power-on count of the panel
Items for use by engineers
Indications of data such as HDMI signal judgment
(For details, see the corresponding page.)
Items for use by engineers
See "Structure of Layers in Panel Factory Mode."
Items for use by engineers
ON/OFF of the SG signal from the MAIN VDEC
(composite input signal required)
Selection of the SG signal
Items for use by engineers
Factory-preset items (Setup must be executed after
replacement of the Main Assy.)
Items for use by engineers
For transferring backup data (after replacement of
the DIGITAL Assy)
To clear data of the digital video
For clearance of data for the corresponding items.
The clearing method is the same: Select "CLEAR",
using [\], then hold [SET] pressed for at least 5
seconds. After clearance is completed, {ETC} is
automatically selected.
For use while Raster Mask (full mask) is displayed.
Use [»] or [«] to select the type of mask.
For use while Pattern Mask is displayed. Use [»] or
[«] to select the type of mask.
For use while Combination Mask is displayed.
Use [»] or [«] to select the type of mask.
8
A
B
C
D
E
F
7