1. Manuals
  2. Brands
  3. Adam Manuals
  4. Indoor Fireplace
  5. ADI0009
  6. Use & care manual

Adam ADI0009 Use & Care Manual

Wall hanging electric fire
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
W A L L H A N G I N G E L E C T R I C F I R E
www.adamfires.co.uk

Advertisement

Table of Contents
loading

Related Manuals for Adam ADI0009

Summary of Contents for Adam ADI0009

  • Page 1 W A L L H A N G I N G E L E C T R I C F I R E www.adamfires.co.uk...

  • Page 2: Table Of Contents

    Read ALL the instructions before use. These instructions are for your safety. Please read through them thoroughly before use and retain for future reference. Failure to follow them could cause injury and/or property damage. Note: This manual applies for a number of different products. Please make sure you follow the appropriate product guide lines.

  • Page 3: Cautions

    CAUTIONS DO’S • Read ALL the instructions before using this fire. • Only use this appliance for its intended use as described in this manual. • Always install the product in accordance with this guide. If in doubt obtain expert advice. •...
  • Page 4 PLEASE DO NOT OBSTRUCT THE AIR VENTS OF THE FIRE’S HEATER UNIT This appliance has a ‘self resetting’ safety cut out system. To prevent overheating, ensure the air inlets and outlets are not obstructed. If the safety cut-out operates, switch off the fire and allow to fully cool down. Remove any obstruction before re-use.

  • Page 5: Introduction

    INTRODUCTION Thank you for choosing this wall mounted electric fire. The fire is designed to meet the most stringent quality, performance and safety requirements. This guide aims to improve your understanding and appreciation of your new fire by providing simple and informative assembly instructions.

  • Page 6: Tools Required

    TOOLS REQUIRED • Crosshead screw driver (an electric screw driver is recomended). • Electric drill • Pencil • Spirit level IDENTIFICATION (Image for illustrative purposes only) Electric fire Fascia* Fuel bed* *Styles may vary depending on product PARTS SUPPLIED Electric fire Fascia (Either supplied fitted to the fire or in a separate box to the electric fire) Pebble set...

  • Page 7: Installation

    INSTALLATION Important Electrical Safety The fire must NOT be located immediately below a socket outlet. The socket must always be accessible in order to disconnect the fire from the electrical supply for maintenance and cleaning or isolation in an emergency. NOTE: Please take care when installing the fire as some edges may be sharp.
  • Page 8 1. Using the template provided and a 2. For solid walls, drill the 2 marked holes spirit level, mark the locations of the 2 using a 6.25mm drill bit, then fit the upper fixing holes with a pencil. supplied wall plugs. Note: if fitting to plaster board, propriety wall fixings should be used (not supplied)
  • Page 9 ATTACHING AND REMOVING THE FASCIA 1. HOOK 3. LIFT 2. CLICK 2. PULL 1. PUSH HOOK the fascia on to the fire then PUSH the tab underneath the fire then CLICK to secure. PULL and LIFT the fascia off the fire...

  • Page 10: Use

    The appliance is controlled using 3 switches, located to the left of the heater unit. Controls Use the following sequence to operate. The grey represents a ‘pressed switch.’ A switch is in the ON position when the side with the markings on (e.g. I or II) is 'pressed in’.

  • Page 11: Specification

    PLUG REPLACEMENT (for product fitted with BS plug) This appliance is supplied with a BS1363 3 pin plug fitted with a 13 Amp fuse. Should the fuse require replacement, it must be replaced with a fuse rated at 13 Amp and approved to BS1362.
  • Page 12 CONFORMITY WITH DIRECTIVES Conforms with relevant European Directives ENVIRONMENTAL PROTECTION • (WEEE) Waste Electrical and Electronic Equipment Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

  • Page 13: Trouble Shooting

    SAFETY CUT-OUT DEVICE To ensure against the potential hazard caused by blockage of the air outlet, this unit is equipped with an automatic over-temperature safety cut-out device. When the device is activated the heater will not operate. If this occurs, the unit can be reset using the following procedure.
  • Page 14 NOTES...
  • Page 15 NOTES...

  • Page 16: Guarantee

    AFFIX RECEIPT OR PROOF OF PURCHASE HERE GUARANTEE For your convenience, you are not required to complete a form and return it to us in order to validate your guarantee. However, please ensure that you retain your receipt which will act as both proof of purchase and a guarantee validation document.

Table of Contents