Page 1 Renault TWINGO Driver’s handbook...
Page 2 Renault cars. Lasting protection and optimum performance for your engine – guaranteed. Whether changing the oil or simply topping up, to find the approved ELF lubricant best suited to your vehicle, ask your Renault dealer for a recommendation or consult your vehi- cle maintenance handbook.
Page 3: Driving
This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
Page 5: Table Of Contents
Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
Page 7 Section 1: Getting to know your vehicle Key/radio frequency remote controls: general information, use, deadlocking ....Opening and closing the doors ........... . . Locking, unlocking the opening elements .
Page 8 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Radio frequency remote Remote control with switchblade Key C control unit A or B 5 Locks/Unlocks the key insert for 1 Locks all the opening elements. remote control B. To release the 2 Unlocks all the opening elements.
Page 9 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surroun- dings: take care not to lock or unlock the doors by inadvertently pressing the buttons on the remote control. Replacement and additional keys or remote controls.
Page 10: Locking The Doors
RADIO FREQUENCY REMOTE CONTROL UNIT: use Remote controls A and B are used to lock or unlock the doors. They are powered by a battery which must be replaced (refer to the informa- tion on “Radio frequency remote con- trol: batteries” in Section 5). Locking the doors Press locking button 1.
Page 11 DEADLOCKING If fitted to the vehicle, this allows the Press button 1 twice in quick succes- doors to be locked and prevents them sion. from being opened with the interior The hazard warning lights and indica- handles (for example, by breaking the tor lights flash three times to indicate window and then trying to open the locking.
Page 12: Opening And Closing The Doors
OPENING AND CLOSING THE DOORS (1/2) Opening the doors from the Rear doors Opening from the inside outside With the doors unlocked, slide your Pull the handle 3. hand into the handle 2 and pull towards Front doors you. With the doors unlocked, place your hand under the handle 1 and pull it to- wards you.
Page 13: Special Note
OPENING AND CLOSING THE DOORS (2/2) Lights-on reminder buzzer If you have switched off the ignition and left the lights switched on, a re- minder buzzer will sound when a door is opened. Door/tailgate open buzzer If an opening (door or boot) is left open Driver’s responsibility or improperly closed, once the vehicle when parking or stopping...
Page 14: Using The Key
LOCKING/UNLOCKING THE DOORS (1/2) Locking/unlocking from the outside This is done using the remote con- trol: please refer to the information on “Radio frequency remote control: gen- eral information” in Section 1. In some cases, the radio frequency remote control may not work: –...
Page 15 LOCKING/UNLOCKING THE DOORS (2/2) Locking the opening Door and tailgate status elements without the radio indicator frequency remote control With the ignition on, the warning light integrated in switch 2 informs you of the For example, in the event of a dis- locking status of the opening elements: charged battery or the radio frequency remote control temporarily not working.
Page 16 RENAULT ANTI-INTRUDER DEVICE (RAID) Activating/deactivating the function With the engine running, press the button 1 for approximately 5 seconds, until you hear a warning beep. Operating faults If you experience an operating fault (no automatic locking, the indicator light incorporated in button 1 does not light up when trying to lock the open- ing elements, etc.), firstly check that the...
Page 17: Front Seats
FRONT SEATS To move the seat forwards or To tilt the seatback Heated seats backwards Depending on the vehicle, activate con- With the ignition on, press the switch 5 trol 1 or 2 and tilt the seatback to the for the seat desired. The indicator light Lift handle 4 to unlock.
Page 18: Seat Belts
SEAT BELTS (1/3) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
Page 19 SEAT BELTS (2/3) Rear seatbelt reminder alert B ß Warning light comes on on the central display when the engine is started, and goes off after around 30 seconds. Warning lights 6 and 7 show the status of the rear seatbelts: –...
Page 20: Rear Seat Belts
SEAT BELTS (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For spe- cial operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 21 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they will con- – Have the entire restraint sist of: system checked following – front seat belt inertia reel preten- an accident. sioners; – No operation whatso- –...
Page 22: Methods Of Restraint In Addition To The Front Seat Belts
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Airbags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at The presence of this equipment is in- an acceptable level.
Page 23 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation Operating faults This system is only operational when å This warning light 2 will light up the ignition is switched on. on the instrument panel when the igni- In a severe frontal impact, the air bags tion is switched on and then go out after inflate rapidly, cushioning the impact...
Page 24 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
Page 25 METHODS OF RESTRAINT IN ADDITION TO THE REAR SIDE SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
Page 26 SIDE PROTECTION DEVICES Side Airbags This airbag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Warning relating to the side airbag –...
Page 27: Additional Methods Of Restraint
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. The airbag is designed to complement the action of the seat belt.
Page 28: Steering Wheel/Power-Assisted Steering
STEERING WHEEL/POWER-ASSISTED STEERING Power Assisted Steering Never drive with an inadequately charged battery. Variable power assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier when ma- noeuvring (for added comfort) while the force needed to steer increases pro-...
Page 29: Child Safety: General Information
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
Page 30 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 31 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
Page 32: Choosing A Child Seat Mounting
CHILD SAFETY: choosing a child seat mounting (1/3) There are two ways of attaching child Attachment using the ISOFIX Before using an ISOFIX seats: via the seat belt or using the system child seat that you pur- ISOFIX system. Authorised ISOFIX child seats are ap- chased for another vehicle, proved in accordance with regulation check that its installation is...
Page 33 CHILD SAFETY: choosing a child seat mounting (2/3) The two rings 1 are located between Rear seats Fix the hook on the ring 5, identified by the seatback and the seat base and are  symbol on the back of the seat Remove the luggage compartment identified by a marking.
Page 34 CHILD SAFETY: choosing a child seat mounting (3/3) Front passenger seat (depending on the vehicle) Attach the belt hook 4 to the ring 3. All seats Pull the belt 3 so that the back of the child seat comes into contact with the back of the vehicle seat.
Page 35: Fitting A Child Seat, General Information
CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting In the front seat After installing the child seat, if neces- child seats. The diagram on the follow- sary, the seat may be advanced (so as The laws concerning children travel- ing page shows you how to attach a to leave enough space in the rear seats...
Page 36 CHILD SAFETY: fitting a child seat, general information (2/2) In the rear side seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with their feet nearest the door. Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will go, although without al-...
Page 37 CHILD SAFETY: attachment by seat belt (1/2) 2-seater vehicle Check the status of the air bag ³ before fitting a child seat or al- lowing a passenger to use the seat. Child seat attached using the belt Seat which allows a seat with ¬...
Page 38 CHILD SAFETY: attachment by seat belt (2/2) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. 2 and 4-seater vehicles: Child seat attached using the seat belt Front passenger Type of child seat Weight of the child...
Page 39 CHILD SAFETY: attachment using the ISOFIX system (1/3) 4-seater vehicle Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The seats ISOFIX are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with “Universal”...
Page 40 CHILD SAFETY: attachment using the ISOFIX system (2/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. 4-seater vehicle: Fitting a child seat ISOFIX. Weight of Type of child seat Seat size Front passenger seat (1) (2)
Page 41 CHILD SAFETY: attachment using the ISOFIX system (3/3) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted. (2) raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
Page 42: Deactivating/Activating The Front Passenger Airbag
CHILD SAFETY: deactivating/activating the front passenger air bag (1/3) Deactivating the front To deactivate the airbags: with the vehicle stopped and the ignition off, passenger airbags push and turn lock 1 to the OFF posi- (on equipped vehicles) tion. You must deactivate the devices in ad- With the ignition on, you must check dition to the front passenger seat belt before fitting a child seat in the front...
Page 43 CHILD SAFETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER...
Page 44 CHILD SAFETY: deactivating/activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbags activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended. Contact your approved dealer as soon as possible.
Page 45: Rear View Mirrors
REAR VIEW MIRRORS Interior rear view mirror Door mirrors with manual Door mirrors with electrical Its position can be adjusted. For night adjustment adjustment driving, to avoid being dazzled by the To adjust the door mirror, move With the ignition on, turn the button 3: headlights of the car behind you, flip the switch 2.
Page 46: Driving Position
DRIVING POSITION: LEFT-HAND DRIVE (1/2) 1.40...
Page 47 DRIVING POSITION: LEFT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Stalk for: 8 Centre air vent. 21 Multimedia system voice control – direction indicator lights; button. – exterior lights; 9 Windscreen demister outlet. –...
Page 48 DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 1.42...
Page 49 DRIVING POSITION: RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side window demister outlet. 11 Driver Airbag and horn location. 18 Cruise control/speed limiter con- trols. 2 Side air vent. 12 Stalk for: –...
Page 50: Warning Lights
WARNING LIGHTS (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Side light warning light Airbag warning light š å This lights up when the ignition is switched on and goes out after a few Main beam headlight tell- á...
Page 51 WARNING LIGHTS (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Handbrake on and brake cir- Oil pressure warning light À cuit incident warning light This lights up when the ignition This comes on when the ignition is is switched on and goes out after a few switched on and goes out as soon as seconds.
Page 52 WARNING LIGHTS (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Toxic Fume Filter System Warning light for electronic Anti-lock braking warning Ä  Warning Light stability program ( ESC ) and light traction control system This lights up when the ignition is On vehicles which are equipped with it, switched on and goes out after a few...
Page 53 WARNING LIGHTS (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Mode warning light ECO Variable power-assisted  steering warning light This comes on when ECO mode is activated. This comes on when the ignition is Please refer to the information on switched on and goes out after a few “Driving advice, Eco-driving”...
Page 54 WARNING LIGHTS (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND THE COUNTRY. ß Seat belt reminder warning lights Please see the information on “Seat belts” in Section 1. ¹ Front passenger airbag deac- tivated warning light Please see the information on “Seat belts”...
Page 55: Displays And Indicators
DISPLAYS AND INDICATORS Automatic gearbox display 3 This indicates the gear engaged (de- pending on the vehicle). Refer to the in- formation on the “Automatic gearbox” in Section 2. Speedometer 1 (km or miles per hour) Overspeed buzzer Depending on the vehicle, a warning beep sounds for approximately 10 sec- onds every 30 seconds, as long as the vehicle is travelling in excess of 75 mph...
Page 56 ON-BOARD COMPUTER: general information (1/2) g) distance travelled since the last reset; h) average speed; i) mileage before next service/oil change; j) Reset the tyre pressure k) cruise control/speed limiter pro- grammed speed; l) set the time. On-board computer 1 Display selection keys 2 and 3 It includes the following functions:...
Page 57 ON-BOARD COMPUTER: general information (2/2) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption, range and average speed will become more stable and reliable the further you travel after pressing the...
Page 58 ON-BOARD COMPUTER: trip settings (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km a) Total mileage recorder. 112.4 km b) Trip mileage recorder. c) Trip settings. 5.8 L/100 Fuel used.
Page 59 ON-BOARD COMPUTER: trip settings (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected e) Current fuel consumption. 7.4 L/100 This value is displayed after a speed of approximately 20 mph (30 km/h) is reached.
Page 60 ON-BOARD COMPUTER: trip settings (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected i) Mileage before service or oil change. Distance remaining until the next service (displayed in miles (kilometres) or days), then when the service nears, the ©...
Page 61 ON-BOARD COMPUTER: trip settings (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected j) Reset the tyre pressure. Please refer to the information on the “Tyre pressure loss ...
Page 62: Clock And Exterior Temperature
CLOCK AND EXTERIOR TEMPERATURE (1/2) 12:00 Display A Wait a few seconds, the minutes will flash: repeatedly press or press and To access the display 2 for setting the hold button 3 or 4 to set the time. time, press button 3 or 4 on the stalk 1. When setting is complete, the hours Wait a few seconds;...
Page 63 CLOCK AND EXTERIOR TEMPERATURE (2/2) External temperature indicator Special note: When the exterior temperature is - 3°C to + 3°C, the °C characters flash (sig- nalling a risk of ice on the road). External temperature in- Display B dicator Vehicles fitted with touch-screen As ice formation is related multimedia, navigation aid systems, to climatic exposure, local...
Page 64: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS (1/3) Dipped beam headlights Manual operation Turn the ring 2 until the symbol is oppo- site mark 3. This indicator light on the instrument panel comes on. Automatic operation (depending on vehicle) Turn ring 2 until the AUTO symbol is op- posite mark 3: with the engine running, the dipped beam headlights switch on or off automatically depending on the...
Page 65 EXTERIOR LIGHTING AND SIGNALS (2/3) Switching off the lights Front fog lights There are two possibilities: Turn the centre ring 4 on the – manually, move ring 2 to position 0; stalk 1 until the symbol is opposite – automatically, if the ring 2 is in mark 3, then release it.
Page 66: Rear Fog Light
EXTERIOR LIGHTING AND SIGNALS (3/3) Turning off the fog lights There are two possibilities: – manually, depending on the vehi- cle, turn the ring 4 again to bring the mark 3 opposite the symbol for the fog light that you want to switch off, or bring the ring 4 into position 0.
Page 67: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode When driving, it is possible that the steering wheel may not be turned suf- ficiently to return the stalk automatically to its starting position.
Page 68: Headlight Beam Adjustment
HEADLIGHT BEAM ADJUSTMENT (1/2) Examples of positions for adjusting control A according to the load Driver alone or with front passenger All seats occupied On vehicles fitted with this function, control A allows you to adjust the height All seats occupied and the boot laden of the beams according to the load.
Page 69 HEADLIGHT BEAM ADJUSTMENT (2/2) When driving on the left in a left-hand Once the adjustment has been done, drive vehicle (or vice versa), you must make sure the bonnet is repositioned adjust your lights temporarily for the and closed properly. duration of your trip.
Page 70 WINDSCREEN WASH/WIPE (1/2) Vehicles with automatic wiper function With the engine running, move stalk 1 – A park. – B automatic wiper function When this position is selected, the system detects water on the wind- screen and triggers the wipers at a suitable wiping speed: –...
Page 71: Windscreen Washer
WINDSCREEN WASH/WIPE (2/2) Do not try to lift the wiper blades. They cannot remain detached from the windscreen. To replace the blades, refer to Section 5: “Wiper blades”. In freezing or snowy weather, ensure they are not stuck to the windscreen (including the central area located behind the interior rear-view mirror) and the rear screen before starting...
Page 72 REAR SCREEN WASH/WIPE Rear windscreen wash/ wiper With ignition on, turn the end of the stalk 2 to bring the mark 1 in line with In freezing or snowy weather, ensure the symbol. When the stalk is released, they are not stuck to the windscreen it returns to the rear windscreen wiper position.
Page 73: Fuel Grade
FUEL TANK (1/2) Fuel grade Petrol version It is essential to use unleaded petrol. Use a high-grade fuel that complies The octane rating (RON) must comply with the legislation in force in each with the information given on the label country and which must comply with on the cover A.
Page 74: Fuel Tank Filling With Fuel
FUEL TANK (2/2) Filling with fuel With the ignition off, insert the nozzle and insert it fully before turning it on to Vehicle fitted with the Stop and fill the fuel tank (risk of splashing). Start function Keep the nozzle in this position To fill up with fuel, the engine must throughout the entire filling operation.
Page 75 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Starting, stopping the engine .
Page 76: Running In
RUNNING IN/STARTING, STOPPING THE ENGINE (1/2) Running in “On” position M The ignition is switched on: Petrol version For the first 600 miles (1,000 km), do Start position D not exceed 78 mph (130 km/h) in the highest gear, or 3,000 to 3,500 rpm. If the engine fails to start at the first attempt, the key must be turned back You may only expect top performance...
Page 77: Starting The Engine
STARTING, STOPPING THE ENGINE (2/2) Starting the engine Stopping the engine Engine warm or cold With the engine idling, turn the key back to the Stop position. – Turn the key to the start position without depressing the accel- erator. –...
Page 78 FUNCTION STOP AND START (1/4) This system enables a reduced fuel For vehicles equipped with manual consumption and lower greenhouse gearboxes: If you get out of the vehicle, a beep gas emissions. The system is acti- notifies you that the engine is on –...
Page 79 FUNCTION STOP AND START (2/4) Preventing the engine from Conditions for coming out of Special note: depending on the vehi- cle, if you switch off the ignition when standing by engine standby the engine is on standby, the warning In certain situations, such as negotiat- For vehicles equipped with auto- Ä...
Page 80 FUNCTION STOP AND START (3/4) Conditions preventing the – the engine temperature is too low; Special feature of the automatic engine re-start standby of the engine – the emission control system is being regenerated; Under certain conditions, the engine Certain conditions prevent the system can restart on its own in order to guar- from using the engine standby function, –...
Page 81 FUNCTION STOP AND START (4/4) The system is automatically reacti- vated each time the vehicle is started (see “Starting, stopping the engine” in Section 2). Operating faults If the warning light 2 integrated on the switch 1 comes on, the system is de- activated.
Page 82: Special Features Of Petrol Versions
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
Page 83: Gear Lever/Handbrake
GEAR LEVER/HANDBRAKE Handbrake To release: Pull the lever 3 up slightly, press button 2 and then lower the lever to the floor. The red warning light on the in- strument panel will come on if you are driving with an incorrectly released handbrake.
Page 84: Driving Advice, Eco-Driving
DRIVING ADVICE, ECO-DRIVING (1/4) Fuel consumption is accredited in ac- cordance with a standard regulatory method. Identical for all manufactur- ers, this enables vehicles to be com- pared with one another. Consumption in real time depends on vehicle usage conditions, the equipment fitted and the user’s driving style.
Page 85 DRIVING ADVICE, ECO-DRIVING (2/4) An overall rating from 0 to 100 is dis- Activating the function played to let you assess your eco driv- Press the switch 3. ing performance. The higher the score,  the better your eco-driving perform- The warning light comes on on ance.
Page 86 DRIVING ADVICE, ECO-DRIVING (3/4) – Avoid sudden acceleration. – Brake as little as possible. If you an- ticipate an obstacle or bend in ad- vance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level.
Page 87 DRIVING ADVICE, ECO-DRIVING (4/4) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Page 88: Maintenance And Antipollution Advice
MAINTENANCE AND ANTIPOLLUTION ADVICE Your vehicle complies with criteria for In addition, replacing engine, fuel – Air filter, fuel filter: a choked ele- recycling and recovering vehicles at the supply system and exhaust compo- ment will reduce efficiency. It must end of their service life which will come nents with parts other than those origi- be replaced.
Page 89: Environment
ENVIRONMENT Emissions Recycling Your vehicle has been designed with respect for the environment in mind for In usage phase, your vehicle was de- Your vehicle is 85% recyclable and its entire service life: during production, signed to emit fewer greenhouse gases 95% recoverable.
Page 90: Tyre Pressure Loss Warning
TYRE PRESSURE LOSS WARNING (1/9) If fitted on the vehicle, this system System identification warns the driver of pressure loss in one There are two tyre pressure loss warn- or several tyres. ing systems: – System A: can be seen on the label A in the vehicle.
Page 91 TYRE PRESSURE LOSS WARNING (2/9) Operating conditions – driving with snow chains; – fitting a single new tyre; The system should be reset with an – use of tyres not approved by the net- inflation pressure equal to that given work.
Page 92 TYRE PRESSURE LOSS WARNING (3/9) SYSTEM A (cntd.) – repeatedly press the button 2 to Resetting the standard level for the  tyre pressures select the “SET ” warning light This should be done: on the display B; – press and hold (around 3 seconds) –...
Page 93 TYRE PRESSURE LOSS WARNING (4/9) System unavailable  Warning light 1 goes out after  Warning light 1 flashes for sev- launching the reset of the tyre pressure eral seconds, then stays on. reference value. System to be checked  Warning light 1 flashes for sev- eral seconds, then stays on.
Page 94 TYRE PRESSURE LOSS WARNING (5/9) SYSTEM A (cntd.) Replacing wheels/tyres Tyre repair product and inflation kit Only use equipment approved by the Only use equipment approved by the Readjustment of tyre pressures brand network, or the system risks brand network, or the system risks The tyre pressures must be adjusted being activated late or not operating being activated late or not operating...
Page 95 TYRE PRESSURE LOSS WARNING (6/9) Resetting the standard level for the tyre pressures This should be done: – when the standard tyre pressure needs to be changed to adapt to usage conditions (empty, carrying a load, motorway driving, etc.); – after swapping a wheel (however this practice is not recommended);...
Page 96 TYRE PRESSURE LOSS WARNING (7/9) When the “SET” warning light flashes Reinitialisation is carried out after a few for around five seconds, this indicates minutes’ driving. that the reset request for the tyre pres- sure reference value has been taken into account.
Page 97 TYRE PRESSURE LOSS WARNING (8/9) Puncture Check tyre sensors   Warning light 1 comes on steady, The warning light 1 flashes for accompanied by a beep and warning several seconds, then stays on, along ® © light with the warning light They indicate that at least one wheel These indicate that at least one of the is punctured or severely underinfla-...
Page 98 TYRE PRESSURE LOSS WARNING (9/9) SYSTEM B (cntd.) Replacing wheels/tyres Tyre repair product and inflation kit This system requires specific equip- Because the valves are specially desi- Readjustment of tyre pressures ment (wheels, tyres, hubcaps, etc.). gned, only use equipment approved by The tyre pressures must be adjusted Please see the information on “Tyres”...
Page 99: Driver Correction Devices/Aids
DRIVER CORRECTION DEVICES AND AIDS (1/4) Anti-lock braking system Depending on the vehicle, this is com- Operating faults: posed of: (ABS) – anti-lock braking system (ABS); © – come on on the Under heavy braking, the ABS prevents – electronic stability control (ESC) instrument panel: ABS, ESC and the wheels from locking, allowing the with understeer control, traction...
Page 100: Electronic Stability Control
DRIVER CORRECTION DEVICES AND AIDS (2/4) Electronic stability control Understeer control The system also adjusts the engine speed to the grip available under the (ESC) with understeer This system optimises the action of the wheels, independently of the pressure control, traction control and ESC in the case of pronounced under- exerted on the accelerator pedal.
Page 101: Emergency Brake Assist
DRIVER CORRECTION DEVICES AND AIDS (3/4) Emergency brake assist Hazard warning lights switching on Depending on the vehicle, these may This system supplements the ABS light up in the event of sudden decel- and helps reduce vehicle stopping dis- eration. tances.
Page 102 DRIVER CORRECTION DEVICES AND AIDS (4/4) Hill start assistance The hill start assistance Depending on the gradient of the in- system cannot completely cline, this system assists the driver prevent the vehicle from when starting on a hill. It prevents the rolling backwards in all sit- vehicle from rolling backwards, de- uations (extremely steep gradients...
Page 103: Lane Departure Warning
LANE DEPARTURE WARNING (1/2) This lane departure warning system no- tifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road.
Page 104 LANE DEPARTURE WARNING (2/2) Deactivation When a line is crossed and the indica- tors have not been activated, the func- Press the switch 1. The warning light 2 tion alerts the driver through warning in the switch 1 goes out. ...
Page 105 CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) The speed limiter function helps you Controls Switching on stay within the driving speed limit that 1 Main “On/Off” switch.  Press the side switch 1 . Indicator you choose, known as the limit speed. light 6 comes on, lit orange, and the 2 Limit speed activation, storage and message “LIMIT”...
Page 106: Speed Limiter
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by re- It is possible to exceed the limit speed peatedly pressing: at any time. To do this: press the accel- erator pedal firmly and fully (beyond –...
Page 107 CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been saved, it can be re- called by pressing switch 4 ((R)). Putting the function on Switching off the function standby The speed limiter function is deac- tivated if you press switch 1: in this The speed limiter function is suspended case a speed is no longer stored.
Page 108 CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. Therefore, it can under no circum- The cruise control function helps you to Controls stances replace the driver’s respon- maintain your driving speed at a speed sibility to respect speed limits and to...
Page 109: Cruise Control
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Switching on Activating cruise control Driving  At a steady speed (above 18 mph Once a cruising speed is memorised Press switch 1 side (30 km/h approximately)) press switch 2 and the cruise control function is active, Indicator light 7 comes on, lit green, or (+): the function is activated and the you may lift your foot off the accelera-...
Page 110 CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
Page 111 CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road con- ditions are suitable (traffic, road sur- face, weather conditions, etc.). Press switch 4 (R) if the vehicle speed is above 20 mph (30 km/h).
Page 112: Parking Distance Control
PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic detectors, installed in the rear bumper (depending on the vehi- cle), measure the distance between the vehicle and an obstacle whilst re- versing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centi-...
Page 113 PARKING DISTANCE CONTROL (2/2) Deactivating the system Press switch 2 to deactivate the system: The indicator light built into the switch lights up to remind you that the system An impact to the under- is deactivated. side of the vehicle while Pressing the switch again will reacti- manoeuvring (e.g.: stri- vate the system and switch off the in-...
Page 114: Reversing Camera
REVERSING CAMERA (1/2) Operation Note: This function is an additio- – ensure that the reversing camera is When going into reverse gear (and up nal aid. It cannot, therefore, not obscured (dirt, mud, snow, etc.); to around 5 seconds after shifting into under any circumstances –...
Page 115 REVERSING CAMERA (2/2) This function is an additio- nal aid. It cannot, therefore, under any circumstances replace the vigilance or the responsibility of the driver. The driver should always pay at- tention to sudden incidents during driving: always ensure that there are no moving obstacles (such as a child, animal, pram, bicycle, etc.) or small, narrow objects such as...
Page 116: Selector Lever
AUTOMATIC TRANSMISSION (1/4) Selector lever 1 Operation Only engage D or R when the vehi- cle is stopped, with your foot on the park With gear lever 1 in position P, start the brake and the accelerator pedal re- engine. reverse leased.
Page 117 AUTOMATIC TRANSMISSION (2/4) Driving in automatic mode Driving in manual mode Special cases Select position D. In most traffic con- With the selector lever in position D, Under certain driving conditions (e.g. ditions, you will not have to touch the move the lever to the left.
Page 118: Parking The Vehicle
AUTOMATIC TRANSMISSION (3/4) Special circumstances Parking the vehicle – If the road contours and bends When the vehicle is stopped, move the do not allow you to stay in auto- lever to position P while keeping your matic mode (e.g.: in the mountains), foot on the brake pedal: the gearbox is we recommend that you change to in neutral and the drive wheels are me-...
Page 119: Automatic Gearbox
AUTOMATIC TRANSMISSION (4/4) Operating faults Breakdown of a vehicle with an To do this, unclip the base of the gear automatic gearbox lever 5 starting on the side below the When three horizontal bars on the dis- Please refer to the information on air conditioning controls.
Page 120 2.46...
Page 121: Your Comfort
Section 3: Your comfort Air Vents ..............Manual air conditioning, heating system .
Page 122 AIR VENTS, air outlets (1/2) 1 Left-hand side window demister 5 Right-hand air vent. outlet. 6 Right-hand side window demister 2 Left-hand air vent. outlet. 3 Windscreen demisting vents. 7 Passenger footwell heater out- 4 Centre air vents. lets. 8 Control panel...
Page 123: Air Vents
AIR VENTS, air outlets (2/2) Centre air vents. Side air vents Direction Air flow Move cursors 9 to the required position. To open air vent 10, press on the air vent (point 11) until it is open as far as required.
Page 124: Manual Air Conditioning, Heating System
MANUAL AIR CONDITIONING, HEATING SYSTEM (1/3) The controls Switching air conditioning on (depending on vehicle) or off 1 Distribution of air in the passenger The air conditioning is switched on compartment. (warning light on) or off (warning light off) using button 2. 2 Air conditioning.
Page 125: Passenger Compartment
MANUAL AIR CONDITIONING, HEATING SYSTEM (2/3) Distribution of air in the passenger compartment Turn the control 1 to choose the distri- bution option. The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed be- tween all the air vents, the front side window demisting vents, the windscreen demisting vents and the...
Page 126 MANUAL AIR CONDITIONING, HEATING SYSTEM (3/3) Adjusting the air temperature Turn the control 5 to obtain the desired temperature. The further towards the red the slide is, the higher the tempera- ture will be. When the air conditioning system is used for long periods, it may begin to feel cold.
Page 127: Automatic Climate Control
AUTOMATIC CLIMATE CONTROL (1/4) Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. You can still adjust the ventilation speed by turning control 6 to increase or reduce the ventilation speed.
Page 128 AUTOMATIC CLIMATE CONTROL (2/4) Clear View function Press button 3 – the integrated indica- tor light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
Page 129 AUTOMATIC CLIMATE CONTROL (3/4) Rear screen de-icing/ Switching air conditioning on demisting or off Press button 8 – the integrated indica- In automatic mode, the system switches tor light comes on. This function en- the air conditioning system on or off, ables rapid demisting or de-icing of the depending on the climate conditions.
Page 130 AUTOMATIC CLIMATE CONTROL (4/4) Air recirculation (isolation of the passenger compartment) This function is managed automatically (operation is confirmed by a warning light on button 7), but you can also acti- vate it manually. – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle;...
Page 131: Air Conditioning: Information And Advice On Use
AIR CONDITIONING: information and advice on use Advice on use Fuel consumption Operating faults In some situations, (air conditioning You will normally notice an increase in As a general rule, contact your ap- off, air recirculation activated, ventila- fuel consumption (especially in town) proved dealer in the event of an oper- tion speed at zero or low, etc.) you may when the air conditioning is operating.
Page 132: Electric Windows
ELECTRIC WINDOWS (1/2) These systems operate with the igni- tion on or off, until one of the front doors is opened (limited to about 3 minutes). Closing windows can cause serious injury. Driver’s responsibility Never leave your vehicle with the key or remote con- trol in it, leaving a child, Press the window switch down or lift it One-touch mode...
Page 133: Rear Windows
ELECTRIC WINDOWS (2/2) Operating faults Electric windows In case of a fault when closing a window, the system reverts to normal mode: pull the switch concerned up as often as necessary to fully close the window (the window will close gradually), hold the switch (still on the closure side) for three seconds then lower and raise the window fully to reinitialise the system.
Page 134: Sunroof
SUNROOF Precautions during use Operating faults – check that the sunroof is properly If the roof will not close, please consult closed before leaving your vehicle; an authorised dealer. – clean the seal every three months using products recommended by our Technical Department;...
Page 135: Interior Lighting
INTERIOR LIGHTING Courtesy light Boot light 2 Press the switch 1 for: It comes on when the boot is opened. – permanent lighting; – lighting controlled by the unlocking of the vehicle or by opening one of the doors. This switches off after a time delay, once the doors concerned have been closed correctly;...
Page 136: Passenger Compartment Storage/Fittings
PASSENGER COMPARTMENT STORAGE/FITTINGS (1/5) Front door storage pockets 1 Dashboard storage 2 Glovebox They can hold a 1.5-litre bottle. Depending on the vehicle, it may be When closed with a cover, lift the fitted with a storage compartment 3. catch 4 to open the glovebox. The cover is fitted with storage areas.
Page 137 PASSENGER COMPARTMENT STORAGE/FITTINGS (2/5) Centre console storage Cup holder 6 Centre console storage compartment 5 compartment 7 This can be used for storing a mobile ashtray, drinks cans, etc. Depending on the vehicle, it is closed with a cover 8. When turning corners, accelerating or braking, ensure that the recepta-...
Page 138 PASSENGER COMPARTMENT STORAGE/FITTINGS (3/5) Rear door storage Cup holder 10 Rear centre console storage compartment 9 compartment 11 This can be used for storing a mobile ashtray, cup holder, etc. Storage compartments can hold a 1.5 litre bottle. When turning corners, Ensure that no hard, heavy accelerating or braking, or pointed objects are...
Page 139 PASSENGER COMPARTMENT STORAGE/FITTINGS (4/5) Storage compartment under Sun visor storage 13 Front sun visor the rear bench seat 12 This can be used for storing motorway Lower sun visor 14. tickets, cards, etc. Vanity mirror Lift the cover 15. When driving, ensure the courtesy mirror cover is closed.
Page 140 PASSENGER COMPARTMENT STORAGE/FITTINGS (5/5) Driver sunglasses holder 16 Passenger grab handle 17 This offers support and can be held when the vehicle is moving. Do not use it for getting into or out of the vehicle. 3.20...
Page 141: Ashtray, Cigarette Lighter, Accessories Socket
ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET Ashtray A Accessories socket 2 It can be housed in either position 1 It is provided for connecting accessories or 3. approved by our Technical Department. Cigarette lighter 2 With the ignition on, push in the ciga- rette lighter 2.
Page 142: Rear Headrests
REAR HEAD RESTS Position for use To raise the headrest Raise the headrest as far as possible to Raise the headrest as far as it will go, use it in the high position. Check that it then press button A and remove the is correctly locked.
Page 143: Rear Bench Seat
REAR BENCH SEAT For safety reasons, carry out any adjustments when the vehicle is not being driven. When moving the rear seats, ensure that nothing obstructs the anchorage To fold down the seatback: Increasing the boot volume (depend- points (passenger’s arm or –...
Page 144: Luggage Compartment
BOOT Opening the doors manually from the inside If it is impossible to unlock the tailgate, it can be done manually from inside: – access the luggage compartment by tilting the rear bench seatback(s), – insert a pencil or similar object in recess 5 and slide the unit as shown in the illustration;...
Page 145: Luggage Cover
LUGGAGE COVER Removal – Unhook the two straps 1; – depending on the vehicle, detach the flexible section attached to the rear bench seatback; – lift the boot cover and unclip it by pulling it towards you. Refitting To refit, proceed in the reverse order to Do not place any heavy or removal.
Page 146 BOOT ARRANGEMENTS Hooks 1 Anchorage points These can be used to hang bags. Attachment points 2. If your vehicle is not equipped with As the engine is located under the anchorage points, you can get them boot, do not slide or store anything from an authorised dealer.
Page 147: Transporting Objects In The Luggage Compartment
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). – The front seatbacks with the rear seatbacks folded down, as is the case for maximum loads (example B).
Page 148: Roof Bars
ROOF BARS/SPOILER Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the opera- tion of the tailgate.
Page 149: Multimedia Equipment
MULTIMEDIA EQUIPMENT The presence and location of this equip- ment depends on the vehicle version. 1 Multimedia touchscreen; 2 Steering column control; 3 Voice commands; 4 Multimedia sockets; 5 Microphone. 6 Telephone holder. Using the telephone We remind you of the need to conform to the legislation in force concerning the use of such equipment.
Page 150 3.30...
Page 151 Section 4: Maintenance Engine access flap ............. . Engine oil level: general information .
Page 152: Engine Access Flap
ENGINE ACCESS FLAP Closing and locking the engine access flap Check that nothing has been left in the engine compartment. – Take the flap; – place it on top of the engine; – tighten the six screws 1 using a flat- blade screwdriver or similar;...
Page 153: Engine Oil Level: General Information
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for – Remove the dipstick and wipe with a lubrication and cooling of moving parts clean, lint-free cloth; and it is normal to top up the level be- –...
Page 154: Engine Oil Level: Topping Up/Filling
ENGINE OIL LEVEL: topping up/filling (1/2) Once the operation has been comple- ted, ensure that the dipstick is pushed in as far as it will go and that the cap is completely screwed in. Topping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is star- ted up for the first time in the day).
Page 155: Oil Change
ENGINE OIL LEVEL: topping up, filling OIL CHANGE (2/2) Oil change Engine oil grade Service interval: refer Refer to the Maintenance Service Maintenance Service Booklet for your Booklet for your vehicle. vehicle. Oil change capacity Please refer to the maintenance docu- ment for your vehicle, or contact an au- thorised dealer.
Page 156: Bonnet
BONNET (1/2) Unlocking the bonnet catch Depending on the vehicle, insert the ve- Opening the bonnet hicle key in the lock 4 and turn. Unclip each cover 1 by holding side 2. Pull the tabs 3 as far as they will go to unlock the bonnet.
Page 157: Closing The Bonnet
BONNET (2/2) Closing the bonnet Locking the bonnet Slide the bonnet back until it closes – Push the tabs 3; (movement B). – depending on the vehicle, insert the vehicle key in the lock 4 and turn; – replace the covers 1; –...
Page 158: Levels
LEVELS (1/3) Frequency of checking coolant level Replacement interval Check the coolant level regularly Refer to the Maintenance Document for (very severe damage is likely to be your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
Page 159: Brake Fluid
LEVELS (2/3) Level 2 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI" warn- ing line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from the manufacturer’s net- work or web site.
Page 160: Windscreen Washer Reservoir
LEVELS /FILTERS (3/3) Filters The filter elements (air filter, passenger compartment filter, etc.) should be re- placed during the maintenance opera- tions carried out on your vehicle. Replacement intervals for filter el- ements: refer to the Maintenance Document for your vehicle. Windscreen washer reservoir If there is an abnormal or repeated drop in the fluid level, please consult...
Page 161: Battery
BATTERY Replacing the battery 1 As this operation is complex, we advise you to contact an approved Dealer. This is located under the bonnet and Label A does not need to be serviced. You Observe the indications on the battery: should not open it or add any fluid.
Page 162: Tyre Pressure
TYRE PRESSURE (1/2) Vehicle fitted with a tyre pressure loss warning system If under-inflated (puncture, low pres-  sure, etc.), the warning light on the instrument panel comes on. See “Tyre pressure loss warning” in Section 2. Label A B: size of vehicle front tyres. C: size of vehicle rear tyres.
Page 163 TYRE PRESSURE (2/2) Tyre safety and use of snow chains: Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains. For your safety, please re- spect the speed limit. When they need to be re- placed, only tyres of the same make, size, type and profile...
Page 164: Bodywork Maintenance
BODYWORK MAINTENANCE (1/2) What you should not do You should A well-maintained vehicle will last longer. It is therefore recommended to Do not degrease or clean mechani- Wash your car frequently, with the maintain the exterior of the vehicle reg- cal components (e.g.
Page 165 BODYWORK MAINTENANCE (2/2) Vehicles with a matte paint Using a roller type car wash Respect local regulations about wash- ing vehicles (e.g. do not wash your ve- finish Return the windscreen wiper stalk to hicle on a public highway). the Park position (refer to the informa- This type of paint requires certain pre- Observe the vehicle stopping distances tion on the “Windscreen washer, wiper”...
Page 166: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g.: instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, mul- larly.
Page 167 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
Page 168 4.18...
Page 169: Practical Advice
Section 5: Practical advice Tyre inflation kit ..............Tyres (tyre and wheel safety, use in winter) .
Page 170 TYRE INFLATION KIT (1/4) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 171 TYRE INFLATION KIT (2/4) – press switch 5 to inflate the tyre to the recommended pressure (please refer to the information on “Tyre in- flation pressure” in Section 4); – after a maximum of 15 minutes, stop inflating and read the pressure (on pressure gauge 6).
Page 172 TYRE INFLATION KIT (3/4) Once the tyre is correctly inflated, – If the pressure is greater than 1.3 bar remove the kit: slowly unscrew the con- but less than the recommended tainer inflation adapter 3 to avoid any pressure (refer to the label affixed to product release and store the container the edge of the driver’s door), read- in plastic packaging to prevent release...
Page 173: Tyre Inflation Kit
TYRE INFLATION KIT (4/4) Precautions when using the The kit should not be operated for more than 15 consecutive minutes. The container must be replaced after the first use even if liquid remains inside. Following repair with the kit, do not travel further than 120 miles (200 km).
Page 174: Tyres (Tyre And Wheel Safety, Use In Winter)
TYRES (1/3) Tyre and wheel safety When the tyre tread has been worn to the level of the warning strips, they The tyres are the only contact between become visible 2: it is then neces- the vehicle and the road, so it is essen- sary to replace your tyres because the tial to keep them in good condition.
Page 175: Tyre Pressures
TYRES (2/3) Tyre pressures If the pressures cannot be checked Vehicle fitted with a tyre pressure when the tyres are cold, increase the loss warning system Adhere to the tyre pressures. The tyre pressures from 0.2 to 0.3 bar (or 3 PSI). If under-inflated (puncture, low pres- pressures should be checked at least ...
Page 176 TYRES (3/3) Use in winter Snow or winter tyres Studded tyres We would recommend that these be This type of equipment may only be Chains fitted to all four wheels to ensure that used for a limited period and as laid For safety reasons, only fit chains your vehicle retains maximum adhe- down by local legislation.
Page 177 FRONT HEADLIGHTS: changing bulbs (1/2) Dipped/Main beam headlight It is essential to use anti-U.V. 55W Direction indicator lights bulbs so as not to damage the plastic To change the bulb: Turn the bulb holder 2 a quarter of a on the headlights. turn and take out the bulb.
Page 178: Daytime Running Lights
FRONT HEADLIGHTS: changing bulbs (2/2) Additional lights If you wish to fit fog lights to your ve- hicle, please see an authorised dealer. Daytime running lights 4 Please see an authorised dealer. Front fog lights 5 – Access the bulb holder via the un- Any operation on (or modi- derneath of the vehicle;...
Page 179 REAR AND SIDE LIGHTS: changing bulbs (1/3) Side lights/brake and – remove the bulb holder by releasing the four clips 3; direction indicator lights – change the bulb; – From the boot, open the cover 1; – refit the bulb holder and push the –...
Page 180 REAR AND SIDE LIGHTS: changing bulbs (2/3) 4 Side light and brake light High-level brake light 8 Number plate lights Bulb type: P21/5W. Consult an approved dealer. – Unclip light 9 by pressing tab 10; 5 Direction indicator lights – remove the light cover to gain access Bulb type: PY21W.
Page 181 REAR AND SIDE LIGHTS: changing bulbs (3/3) Side indicator lights Unclip the indicator light 11 using a flat- blade screwdriver or similar. Turn the bulb holder a quarter of a turn and take out the bulb. Bulb type: W5W. Replace the bulb and refit the indicator light.
Page 182: Interior Lighting: Changing Bulbs
INTERIOR LIGHTING: changing bulbs Courtesy light Luggage compartment light Press tab 3 to release the bulb holder and access bulb 4. Unclip the lens (using a flat-blade Unclip light 2 by pressing the tabs on Bulb type: C5W festoon type bulb. screwdriver or similar).
Page 183: Fuses
FUSES (1/3) Fuses in passenger compartment A Fuses in engine compartment B Some functions are protected by fuses If any electrical component does not located in the engine compartment work, check the condition of the fuses. (unit B). To comply with current legislation, Unclip the access flap A.
Page 184 FUSES (2/3) Allocation of fuses (the presence of certain fuse depends on the vehicle equipment level) 5.16...
Page 185 FUSES (3/3) Number Allocation Number Allocation Number Allocation “Starting” position on the Headlight beam height/rear energy management ECU/ ignition-starter switch parking distance control/ passenger compartment front camera adjustment Power-assisted steering ECU/headlights/daytime running lights Lighting Injection Airbags Reversing light/rear Lighting Right headlight/energy windscreen wiper management ECU Instrument panel...
Page 186: Radio Frequency Remote Control: Batteries
RADIO FREQUENCY REMOTE CONTROL: batteries (1/2) Replacing the battery Note: It is not advisable to touch the electronic circuit in the key cover when Open the case at slot 1 using a flat- replacing the battery. blade screwdriver or similar, and re- place the battery 2, observing the type and polarity shown on the back of the cover.
Page 187 RADIO FREQUENCY REMOTE CONTROL: batteries (2/2) Operating faults If the battery is too weak to ensure cor- rect operation, you can still start and lock/unlock the vehicle (please refer to the information on “Locking/unlocking the opening elements” in Section 1). Do not throw away your used batteries;...
Page 188: Connecting A Battery Charger
BATTERY: breakdown recovery (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any electrical consumers The battery charger must be com- (courtesy lights, etc.) are switched patible with a battery with nominal off before disconnecting or recon- voltage of 12 volts.
Page 189 BATTERY: breakdown recovery (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
Page 190: Fitting A Radio
FITTING A RADIO – In all cases, it is very important to follow the manufacturer’s instruc- tions carefully. – The specifications of the brack- Radio location 1 Door speakers 2 ets and wires (available from our network) vary depending on the Unclip the blanking cover.
Page 191: Accessories
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 Watts only.
Page 192 WINDSCREEN WIPER BLADES (1/2) To refit Proceed in reverse order. Make sure that the blade is correctly locked in po- sition. Replacing windscreen wiper blades 1 – In frosty weather, make Ignition switched off, sure that the wiper blades are not stuck by ice (to –...
Page 193 WINDSCREEN WIPER BLADES (2/2) To refit Proceed in reverse order. Make sure that the blade is correctly locked in po- sition. Rear screen wiper blade 5 Ignition switched off, – Lift the wiper arm 5; – release the blade 6 by pulling it. 5.25...
Page 194: Towing
TOWING: breakdown recovery (1/2) Towing a vehicle with an Before any towing, put the gears into neutral (neutral position for vehicles automatic gearbox equipped with a manual gearbox or N With the engine switched off, the trans- position for vehicles equipped with an mission is no longer lubricated.
Page 195 TOWING: breakdown recovery (2/2) – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. – A vehicle must not be towed if it is not fit to be driven.
Page 196: Operating Faults
OPERATING FAULTS (1/6) Using the remote control POSSIBLE CAUSES ACTION REQUIRED The remote control does not lock or The remote control battery is flat. Use the emergency key. unlock the doors. Use of appliances operating on the same Stop using the devices or use the key. frequency as the remote control (mobile phone, etc.).
Page 197 OPERATING FAULTS (2/6) The following advice will enable you to carry out quick, temporary repairs. For safety reasons, you should always contact an approved Dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights are Battery terminals disconnected, Retighten, reconnect or clean them if they weak or fail to light up and the starter does...
Page 198 OPERATING FAULTS (3/6) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to the correct pres- Check the tyre pressures: if this is not the sure, incorrectly balanced or dam- problem, have them checked by an ap- aged.
Page 199 OPERATING FAULTS (4/6) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved Dealer. The engine overheats. The coolant Engine cooling fan not working. Stop the vehicle, switch off the engine and temperature indicator and the warn- contact an approved Dealer.
Page 200 OPERATING FAULTS (5/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”.
Page 201 OPERATING FAULTS (6/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO Traces of condensation in the lights. Traces of condensation may be a nat- ural phenomenon caused by varia- tions in temperature. In this case, the traces will disappear slowly once the lights are switched The front seat belt reminder light An object is stuck between the floor Remove all objects from underneath the...
Page 202 5.34...
Page 203: Technical Specifications
Section 6: Technical specifications Vehicle identification plates ............Engine identification plate .
Page 204: Vehicle Identification Plates
VEHICLE IDENTIFICATION PLATES The information shown on the ve- 4 MMAC (Maximum permissible hicle identification plate should be all-up weight). quoted on all correspondence or 5 MTR (Gross Train Weight) orders. 6 MMTA (Maximum Permissible Weight) front axle. The presence and location of the in- 7 MMTA rear axle.
Page 205: Engine Identification Plate
ENGINE IDENTIFICATION PLATES Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 206 DIMENSIONS (in metres) 1,454 (1) to 1,459 0,630 à 0,638 2,492 to 2,495 0,473 à 0,490 1,430 (2) to 1,459 3,595 to 3,623 1,544* to 1,554* 1,434 to 1,444 (1) 1,434 to 1,442 (2) (1) Vehicle with 15” wheels 1,875 (2) Vehicle with 16”...
Page 207: Engine Specifications
ENGINE SPECIFICATIONS Versions 0.9 TCe Engine type (see engine plate) Cubic capacity (cc) It is essential that you use unleaded petrol of the octane rating stated on the label inside Type of fuel the fuel filler flap. Octane rating Spark plugs Only use the spark plugs specified for your vehicle’s engine.
Page 208: Weights
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer. Maximum permissible all-up weight (MMAC) Weights are indicated on the vehicle identification plate (refer to Maximum permissible all-up weight (MMTA) the information on “Vehicle identification plates”...
Page 209: Replacement Parts And Repairs
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 210: Service Sheets
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 211 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 212 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 213 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 214 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 215 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 216: Anticorrosion Check
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.14...
Page 217 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
Page 218 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
Page 219 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 220 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 221: Alphabetical Index
ALPHABETICAL INDEX (1/5) changing a bulb ............5.9 → 5.14 ABS ..............1.46, 2.25 → 2.28 changing gear ..........2.9, 2.42 → 2.45 accessories................ 5.23 child restraint/seat ......1.23 – 1.24, 1.26 → 1.36 accessories socket ............3.21 child safety......1.7, 1.18, 1.23 – 1.24, 1.26 → 1.36 additional methods of restraint ..........
Page 222 ALPHABETICAL INDEX (2/5) driving recommendations ........2.10 → 2.13 front seats adjustment ............1.11 – 1.12 fuel ECO driving ............2.10 → 2.13 advice on fuel economy ........2.10 → 2.13 ECO mode ................. 2.11 consumption ........1.52 – 1.53, 2.10 → 2.13 electric beam height adjustment ......1.62 – 1.63 filling ............
Page 223 ALPHABETICAL INDEX (3/5) main beam headlights ........1.44, 1.58, 5.9 ignition switch ............. 2.2 – 2.3 reversing lights ............. 5.12 indicators ............1.61, 5.9 → 5.13 side lights .......... 1.58, 5.9 – 5.10, 5.12 indicators: load permitted on the roof............ 6.6 direction indicators ............
Page 224 ......... 2.2 – 2.3 batteries ............5.18 – 5.19 remote control door locking unit ........1.2 → 1.4 tailgate ............3.24, 3.26 – 3.27 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.10 tanks and reservoirs replacement parts ..............6.7 brake fluid ..............4.9 reverse gear coolant ................
Page 225 ALPHABETICAL INDEX (5/5) tyres ......2.13, 2.16 → 2.24, 4.12 – 4.13, 5.6 → 5.8 unlocking the doors ............ 1.8 – 1.9 variable power-assisted steering ........1.22 vehicle identification plates ..........6.3 ventilation ..............3.2 → 3.11 warning lights............1.44 → 1.55 washing ..............
Page 228 à999105452Rö ê î ä X2 RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Renault TWINGO Driver's Handbook Manual

Table of Contents

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Section 6: Technical Specifications

Quick Links

Chapters

Related Manuals for Renault TWINGO

Summary of Contents for Renault TWINGO

Table of Contents