Advertisement
2.5.2 Output Signal check (03/04)
In the "03"or"04"test mode,the folloeing output signal conditions can be checked by entering appropiate
codes.
Code Function
1
DRM-MOT
2
FED-MOT
*1
3
RGT-MOT
4
HTR-MOT
5
DEV-MOT
6
TNR-MOT
7
OPT-FAN-MOT
8
EXIT-FAN-MOT
9
AUG-MOT
41
ADD-FED-MOT
42
ADD-RGT-MOT(Stack) ON
43
ADD-RGT-MOT(Feed) ON
61
PD-MOT
62
FD2-CLT
*2
FD3-CLT
FD4-CLT
63
RGT2-CLT
*2
RGT3-CLT
RGT4-CLT
65
DEV-FAN
67
BTM-FAN
68
CH-FAN
HTR-FAN
*3
20
SCN-MOT
21
LNS-MOT
22
MRR-MOT
23
CLN-MOT
24
DCM-MOT
25
CLN-TR-MOT
*4
26
TRAY-MOT(LCF)
*5
45
STOP-MOT
*6
46
GUIDE-MOT
*7
64
TR2-MOT(PFP)
TR3-MOT(PFP)
TR4-MOT(PFP)
*1 The feed motor will rotate in the direction appropriate for the cassette loaded at the time of the output signal
check.
*2 For FD2~4-CLT and RGT2~4-CLT,the clutch appro priate for the cassette loaded at the time of the output signal
check will be driven.
*3 The scanning motor will run at the correct speed for the reproduction ratio selected(and displayed)at the time of
the output signal check.
*4 The tray motor moves the tray up when the PRINT key is pressed once,and is turned off when the tray-up switch
is turned on.When the PRINT key is pressed a second time,it moves the tray down and is turned off when the
tray-down switch is turned on.
*5 The length guide motor performs initalisation when the PRINT key is pressed once.When the PRINT key is
pressed a second time, it moves the paper length guide to the widest setting position and then is turned off.When
the PRINT key is pressed a third time,it moves the paper length guide in for a narrow setting and is turned off
when the length guide home switch is turned on.
*6 The width guide motor widens the paper width guide when the PRINT key is pressed once and is turned off when
the width guide home switch is turned on.When the PRINT key is pressed a second time,it narrows the paper
width guide until the A4-R size position and then is turned off.When the PRINT key is pressed a third time,it,widens
the guide until the A3 size position and is turned off.
*7 For TR2 to 4-MOT,the motor appropriate for the cassette loaded at the time of output signal check is chosen.When
the PRINT key is pressed once, the motor moves the tray up and is turned off when TUP2 to 4-SW is turned
on.When the PRINT key is pressed a second time,it moves the tray down and is turned off after a set time lag.
*8 The exposure lamp stays on for 5 sec.and then goes off automatically.
65/5560 ADJUSTMENT
Stop code
Code
ON
11 OFF
30
ON
12 OFF
ON
13 OFF
31
ON
14 OFF
ON
15 OFF
32
ON
16 OFF
HIGH
17 LOW
33
HIGH
18 LOW
34
ON
19 OFF
ON
51 OFF
35
52 OFF
37
53 OFF
38
ON
71 OFF
48
49
ON
72 OFF
81
82
83
ON
73 OFF
84
ON
75 OFF
HIGH
77 LOW
85
ON
78 OFF
86
Changes direction
each time the PRINT
key is pressed.
2-9
Function
HV-M
(Main charger output)
HV-TR
(Transfer charger output)
HV/AC
(Transfer charger output)
EXP-LAMP
GBIAS
(Transfer bias output)
PRE-TR-C4
SCRP-SOL
MANUAL-SOL
ADD-SOL
GATE-SOL
ADF-FEED-MOT(CW)
ADF-FEED-MOT(CCW)
ADF-CLU
ADF-BELT-MOT(CW)
ADF-CLU
ADF-BELT-MOT(CCW)
ADF-FEED-MOT(CCW)
ADF-BELT-MOT(CW)
ADF-CLU
STP-SOL
FLP-SOL
ADF-CLU
BRKE
MAY.1997 © TOSHIBA CORP.
ON/OFF
ON/OFF
ON/OFF
ON/OFF
*8
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
Advertisement
