Fitting Battery; Operation - Worx WG784E Manual

1. fiTTiNG ThE haNdLE (See b1~b5)
1) Remove the screws (X 2) on the both side
of deck. (Fig. B1)
2) Insert the lower handle (9) into the holes on
the deck provided.(Fig. B2)
3) Secure with the screws provided.(Fig B2)
4) Attach the upper handle (7) with the bolts
and lock cam lever (8) to the lower handle
(9). (Fig. B3)
5) Tightening the two Lock cam levers. Check
that the handle is FULLY secured.
The cam lever pressure can be adjusted by
adjusting the lock cam lever (8) clockwise/
counter-clockwise. DO NOT OVER TIGHTEN.
(Fig. B4)
NOTE: Ensure the bolts are fully inserted
through the handles before fitting the
handle knobs.
6) Attach the cable clips (2) provided, to the
upper and lower handle. Insert the cable
into the clips ensuring there is enough
cable slack. (Fig. B5)
2. GRaSS COLLECTiON baG aSSEmbLy
Connect the grass box handle to the box top
as shown in Fig. C1-C4.
Step 1 press the front of the handle briefly.
(Fig. C2)
Step 2 Then push it forward. (Fig. C2)
Step 3 push down the back of the handle.
(Fig. C2)
Step 4 Finally, clip the plastic clips over the
metal frame. (Fig. C3)
waRNiNG: don't fit the handle in
reversed direction. fit the handle as
shown in fig. C1.
3. GRaSS COLLECTiON baG fiTTiNG
(See fig. d1, d2, d3)
1) Turn the mower off, wait until blade stops
and remove safety key (6).
2) Raise the safety flap (10) and hold it up,
ensure that the mulching insert has been
removed.
3) pick up the grass bag by the handle, and
position grass bag on the lower hooks (a)
on the mower deck (Fig. D2).
4) Release the safety guard to lock the grass
bag into position. Ensure the grass bag is
installed securely (Fig. D3).
Cordless lawn mower
NOTE: Depress the grass bag slightly to
ensure that it is completely installed.
4. REmOViNG/EmPTyiNG
Hold the grass bag, lift the safety flap (10) and
hold up. Remove grass bag (4).
waRNiNG! Always check the safety flap
can close the discharge outlet tightly
before using. Never lift the safety flap (10)
when the lawn mower is being used without
fitted grass bag.
5. haNdLE adJUSTmENT (See fig. E)
The upper handle can be adjusted to 3
different height positions. Release the locking
cam lever, set the upper handle to one of the
three height positions, and make sure to insert
the pin into the hole. Then reset the locking
cam lever.
NOTE: Always check that the upper handle is
fixed firmly.
6. fiTTiNG/REmOViNG baTTERy (See
fig. f1, f2)
REmOViNG baTTERy
pull out the battery with the battery handle
directly. (See Fig. F1)
NOTE: Be careful not to drop the battery onto
your foot or on the ground when removing it.

fiTTiNG baTTERy

put the battery into the battery container; make
sure the battery is fitted correctly. (See Fig. F2)

OPERATION

1. STaRTiNG aNd STOPPiNG (See fig. G1,
G2)
waRNiNG! The blade continues
to rotate for a few seconds after the
machine is switched off. Allow the motor/blade
to stop rotating before switching "on" again.
Do not rapidly switch off and on.
STaRTiNG
1) Insert safety key into the housing of the
switch box.
2) Slide the key to the right and hold in
position.
13 13
EN