Download Print this page

Emergency Stop Light - Midland BTX1 PRO Instruction Manual

Advanced intercom system
Hide thumbs Also See for BTX1 PRO:

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 15
› Press and hold down the "Middle" button about 7 sec., until the Red light is on perma-
nently.
› Now press firmly (3 sec) the "Vol +" or "Vol -" button, the Blue and Red light will flash.
› Follow now the pairing procedure explained on the manual of the transceiver itself.
Wired audio input
Your Midland BTX1 PRO can be connected to a wired audio source, like an iPod (or any
other MP3 Player).
Listening to music
To listen to music from the wired input, connect the audio source using the optional
AUX cable.
The volume buttons (Vol + and Vol -) can be used to adjust the volume of the wired
audio source (but not independently from the Intercom Volume). The AGC system will
automatically increase the volume on higher speed.
Attention: never set the volume of the MP3 Player to the maximum possible. Normally the
best level is about the 70% of the maximum.
Hint: We recommend that you perform a few tests adjusting the volume of your iPod/MP3
player so at the normal speed the Headset volume is suited to your needs. The AGC system
will automatically increase the volume on higher speed, so you don't need the VOL+ or VOL-
buttons to adjust it.
Enabling/disabling the wired input
If needed the wired input can be enabled or disabled:
Enabling/Disabling: make a Long press (3 sec.) on the "Middle" and "Forward" button
(you will hear one audio beep tone for enabling confirmation and two audio beep tone
for disabling).
Wired audio in background
The audio from the wired connection can be in background to your Intercom or Phone
communication. By default this option is ON. Please refer to the paragraph "Wired con-
nection always in background" below to disable it.
Note that is not possible to have the wired audio source in background to the FM radio.
www.midlandeurope.com

Emergency Stop light

On the back of your BTX1 PRO mounting kit you have an ultra
bright LED emergency stop light. Every time you make a full bra-
ke, the stop light will turn ON to give an extra alert to the drivers
behind you. In case you need to turn it OFF temporarily (for exam-
ple when you ride with a passenger), just press long "Backward" and
"Forward" button togheter while in "Phone" or "Intercom" mode
(a voice announcement will confirm the status). The unit will re-
member the last setting used, that means you need to turn ON
manually the stop light pressing again "Backward" and "Forward"
button togheter.
Attention: By default the stop light is OFF
Setup and special configurations
Resetting all paired devices
Sometimes you may find it necessary to delete all the pairing references stored in the
BTX1 PRO unit (reset operation).
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
› Then simultaneously press and hold down the "Volume +" and "Volume –" buttons for
3 seconds. The Blue Light will be lit on for 1 sec and then back to steady RED.
› Double click on the "Middle" button to exit the "Setup" mode and use the BTX1 PRO.
This procedure deletes all the paired Bluetooth devices stored in the memory therefore
you will not have "Phone" and "Intercom" mode, only "FM Radio" mode will be available.
Back to factory setting
Sometimes you may find it necessary to go back to the factory setting, to reset all the
changes/setup already made and have a "clean" unit.
To perform this operation you must first enter the setup mode:
› Turn off the unit
Stop Light
25

Hide quick links:

Advertisement

loading
Need help?

Need help?

Do you have a question about the BTX1 PRO and is the answer not in the manual?

Subscribe to Our Youtube Channel

This manual is also suitable for:

Btx1 pro
Save PDF