Advertisement
USER'S MANUAL
PROGRAM
RAIN DELAY
RESET
AUTO
Models:
HRC 100-C (96054) 4-Station Update all titles to Indoor/Outdoor Mount, Irrigation Controller
HRC 100-C (96057) 6-Station Update all titles to Indoor/Outdoor Mount, Irrigation Controller
HRC 100-C (96058) 9-Station Update all titles to Indoor/Outdoor Mount, Irrigation Controller
HRC 100-C (96059) 12-Station Update all titles to Indoor/Outdoor Mount, Irrigation Controller
PN 96054-24 rB
Advertisement
Related Manuals for HYDRO-RAIN HRC 100-C 96054
Summary of Contents for HYDRO-RAIN HRC 100-C 96054
- Page 1 USER'S MANUAL PROGRAM RAIN DELAY RESET AUTO Models: HRC 100-C (96054) 4-Station Update all titles to Indoor/Outdoor Mount, Irrigation Controller HRC 100-C (96057) 6-Station Update all titles to Indoor/Outdoor Mount, Irrigation Controller HRC 100-C (96058) 9-Station Update all titles to Indoor/Outdoor Mount, Irrigation Controller HRC 100-C (96059) 12-Station Update all titles to Indoor/Outdoor Mount, Irrigation Controller PN 96054-24 rB...
-
Page 3: Table Of Contents
Congratulations on selecting your new Hydro-Rain irrigation controller! With Hydro-Rain’s exclusive Easy-Set Logic™, simple programming and setup are combined with the latest controller technology and versatility . Your HRC 100 C provides convenience and flexibility, letting you run a fully... -
Page 4: Section 1: Get To Know Your Hrc 100 C
Section 1: Get to know your HRC 100 C Lock and latch Weather Resistant Cover Dial Digital Display Battery Compartment Swing Door panel PROGRAM RAIN DELAY RESET AUTO... -
Page 5: Section 2: Installation
Buttons Function ENTER To confirm a new setting To water manually MANUAL CLEAR To clear a setting PROGRAM To move to different programs: A, B, and C To skip to the next setting / watering station ARROW [ ] or move to other programs/settings To go back to the previous setting / watering ARROW [ ... - Page 6 1. Select a Location 2. Mount the Controller When choosing a location for your HRC 100 C, • Use the mounting template (included) to mark the mounting screw location on the wall . See Figure 1 consider the following: • Choose location near a power source (if hard wiring) or •...
- Page 7 3. Connect Valve Wires to Controller to the controller . To avoid electrical hazards, only one valve should be connected to each station . See Figure 4 • Strip 12 mm of the plastic insulation off the end of each Important: The wire can be buried in the ground;...
- Page 8 4. Connect Electrical Power requirements of the National Electrical Code and other state and local codes. Indoor Locations—Insert the power cord into an 240V electrical This sprinkler controller has two holes at the bottom for wire outlet . access. Use a 12 mm Nipple to connect the sprinkler controller Outdoor Locations—If a covered Ground Fault Interrupter (GFI) to a standard electrical junction box.
-
Page 9: Section 3: Programming With Easy-Set Logic
5. Activate Battery One Lithium CR2032 battery (included) is required to retain the Tip: To increase or decrease more rapidly, hold down either the program in memory during power loss . Annual replacement is [+] or [-] buttons until the display goes into rapid advance mode. recommended . - Page 10 Days of the Week Example: Bill just planted new grass seed and wants to water three times per day . He sets START TIME 1 for 5 a .m ., START • Your dial should be set to [HOW OFTEN] TIME 2 for 12 p .m ., and START TIME 3 for 5 p .m .
-
Page 11: Section 4: Additional Features
Section 4: Additional Features • To adjust press [+/–] buttons, press [ENTER] • If using multiple programs (A, B, C) Press the Rain Delay [PROGRAM] button to move to the desired program and [RAIN DELAY] allows you to delay your sprinkler controller from make the needed adjustment watering for a set period of time . - Page 12 Example: To manually water on station 3 for five minutes, press the [MANUAL] button then press the Rain Sensor Bypass [ ] buttons until you see station 3; using the [+/–] This HRC 100 C is equipped with a sensor override “on/ buttons, set duration to five minutes;...
-
Page 13: Section 5: Reference
program to be erased after a power failure . If this happens, you will need to install a fully charged battery and reprogram • Battery should last approximately one year the controller . • Open by sliding the battery tray out to the right Tip: Replace battery every year, to avoid loss of programming •... - Page 14 Troubleshooting PROBLEM POSSIBLE CAUSE 1 . Faulty solenoid connection 2 . Wire damaged or severed One or more valves do not turn on 3 . Flow control stem screwed down, shutting valve off 4 . Programming is incorrect 1 . Water pressure is too high Stations turn on when they 2 .
- Page 15 .hydrorain .com user’s authority to operate the equipment. Before returning this controller to your authorized Hydro-rain NOTE: This equipment has been tested and found to comply distributor, contact Hydro-Rain Technical Service at: ®...
- Page 17 Registration non printing non printing client: Hydro-Rain on this form. ???? ???? sku: CMYK © 2007 Fluid Studio. This 96054 work is the property of Fluid p 801 295 9820...
Need help?
Do you have a question about the HRC 100-C 96054 and is the answer not in the manual?
Questions and answers
Every time I try to run program "B" manually it defaults back to "A" and runs in Manual when I wanted to run "B" in manual HRC-100 how do I go about running "B" . I select "B" with the program button and hit enter manually and it switches back to "A B C " and starts to run "A" manually
To run program "B" manually on the HYDRO-RAIN HRC 100, first make sure you have selected program "B" before starting manual operation. If it keeps defaulting to program "A," turn the dial to the manual start position, then use the program selection button to switch to program "B" before initiating the manual start. Ensure that program "B" has been properly programmed with start times and run times.
This answer is automatically generated