Juniper SRX5600 Getting Started Manual
Services gateway
Hide thumbs
Also See for SRX5600:
- Hardware manual (483 pages) ,
- Installation and initial configuration manual (205 pages) ,
- Manual (34 pages)
Table of Contents
Advertisement
Quick Links
SRX5600 Services Gateway Getting
Started Guide
December 2013
Part Number: 530-055499
Revision 01
Contents
Copyright © 2013, Juniper Networks, Inc.
This document describes how to install the SRX5600 Services Gateway.
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Step 1: Prepare the Site for SRX5600 Services Gateway Installation . . . . . . . . . . . 4
Rack-Mounting Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Tools Required to Unpack and Prepare the SRX5600 Services Gateway for
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Open-Frame Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 3: Install the Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remove Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Install the Services Gateway Using a Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Install the Services Gateway Without a Mechanical Lift . . . . . . . . . . . . . . . . . 12
Reinstall Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Step 4: Connect the Grounding Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Step 5: Connect External Devices and Network Cables . . . . . . . . . . . . . . . . . . . . . 14
Connect to a Network for Out-of-Band Management . . . . . . . . . . . . . . . . . . . 14
Connect a Management Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connect the Network Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Step 6: Connect Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connect Power to an AC-Powered Services Gateway . . . . . . . . . . . . . . . . . . . 16
Connect Power to a DC-Powered Services Gateway . . . . . . . . . . . . . . . . . . . . 17
Step 7: Perform the Initial Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 20
Enter Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Configure User Accounts and Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Configure System Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Commit the Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1
Advertisement
Table of Contents
Related Manuals for Juniper SRX5600
Summary of Contents for Juniper SRX5600
-
Page 1: Table Of Contents
About This Guide ........... . 3 Step 1: Prepare the Site for SRX5600 Services Gateway Installation ... 4 Rack-Mounting Requirements . - Page 2 SRX5600 Services Gateway Getting Started Guide SRX5600 Services Gateway Compliance Statements for EMC Requirements ..........26 Canada .
-
Page 3: About This Guide
About This Guide About This Guide This guide contains information that you need to install and configure the SRX5600 Services Gateway quickly. For complete installation instructions, see the SRX5600 Services Gateway Hardware Documentation at www.juniper.net/techpubs/ WARNING: This guide contains a summary of safety warnings in “Safety... -
Page 4: Step 1: Prepare The Site For Srx5600 Services Gateway Installation
Step 1: Prepare the Site for SRX5600 Services Gateway Installation Rack-Mounting Requirements on page 4 Tools Required to Unpack and Prepare the SRX5600 Services Gateway for Installation on page 6 Rack-Mounting Requirements You can install the services gateway in a four-post rack or cabinet or an open-frame rack. - Page 5 When you are mounting the services gateway in a partially filled rack, load the rack from the bottom to the top, with the heaviest component at the bottom of the rack. Copyright © 2013, Juniper Networks, Inc.
-
Page 6: Step 2: Install The Mounting Hardware In A Four-Post Rack Or Cabinet Or An Open-Frame Rack
SRX5600 Services Gateway Getting Started Guide Tools Required to Unpack and Prepare the SRX5600 Services Gateway for Installation To unpack the services gateway and prepare for installation, you need the following tools: A mechanical lift—recommended Phillips (+) screwdrivers, numbers 1 and 2 2.5-mm flat-blade (–) screwdriver... - Page 7 Step 2: Install the Mounting Hardware in a Four-Post Rack or Cabinet or an Open-Frame Rack Figure 2: Mounting Hardware for a Four-Post Rack or Cabinet Four-post open rack Small mounting shelf Copyright © 2013, Juniper Networks, Inc.
-
Page 8: Step 3: Install The Services Gateway
SRX5600 Services Gateway Getting Started Guide Figure 3: Mounting Hardware for an Open-Frame Rack Proceed to “Step 3: Install the Services Gateway” on page Step 3: Install the Services Gateway Because of the services gateway’s size and weight, you must remove all components,... -
Page 9: Remove Components
Figure 5: Components to Remove from the Rear of the Services Gateway Before you lift the services gateway, you must remove the following components: Power supplies Cards (SCBs, SPCs, IOCs, Flex IOCs, and MPCs) Air filter Fan tray Copyright © 2013, Juniper Networks, Inc. -
Page 10: Install The Services Gateway Using A Lift
Do not stack removed components. Lay each one on a flat surface. NOTE: For complete instructions on removing services gateway components, see “Install the Services Gateway Without a Mechanical Lift” in the SRX5600 Services Gateway Hardware Guide. Install the Services Gateway Using a Lift To install the services gateway using a lift: Ensure that the rack is in its permanent location and is secured to the building. - Page 11 Visually inspect the alignment of the services gateway. If the services gateway is installed properly in the rack, all the mounting screws on one side of the rack should be aligned with the mounting screws on the opposite side and the services gateway should be level. Copyright © 2013, Juniper Networks, Inc.
-
Page 12: Install The Services Gateway Without A Mechanical Lift
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis. For more information about ESD, see the SRX5600 Services Gateway Hardware Documentation at www.juniper.net/techpubs/ Copyright © 2013, Juniper Networks, Inc. -
Page 13: Step 4: Connect The Grounding Cable
Disconnect the ESD grounding strap from the site ESD grounding point, and connect it to one of the ESD points on the chassis. For more information about ESD, see the SRX5600 Services Gateway Hardware Documentation at www.juniper.net/techpubs/ Place the grounding cable lug over the grounding point. The grounding point is sized for UNC 1/4-20 screws and 1/4 in. -
Page 14: Step 5: Connect External Devices And Network Cables
SRX5600 Services Gateway Getting Started Guide Figure 8: Connecting the Grounding Cable Verify that the grounding cabling is correct, that the grounding cable does not touch or block access to services gateway components, and that it does not drape where people could trip over it. -
Page 15: Connect The Network Cables
Connect the Network Cables Have ready a length of the type of cable used by the interface. For cable specifications, see the SRX5600 Services Gateway Hardware Documentation at www.juniper.net/techpubs/ If the cable connector port is covered by a rubber safety plug, remove the plug. -
Page 16: Step 6: Connect Power Cables
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis. For more information about ESD, see the SRX5600 Services Gateway Hardware Documentation at www.juniper.net/techpubs/ Locate the power cords you will use to connect the device to AC power. See the SRX5600 Services Gateway Hardware Documentation at www.juniper.net/techpubs/... -
Page 17: Connect Power To A Dc-Powered Services Gateway
The services gateway must be running Junos OS Release 12.1X44-D10 or later in order to use high-capacity AC or DC power supplies. Table 3 on page 18 describes the services gateway input voltage requirements. Copyright © 2013, Juniper Networks, Inc. - Page 18 SRX5600 Services Gateway Getting Started Guide Table 3: DC Power System Input Voltage Item Specification DC input voltage Operating range: –40.5 to –72 VDC Ensure that the voltage across the DC power source cable leads is 0 V and that there is no chance that the cable leads might become active during installation.
- Page 19 Connect each DC power cable to the appropriate external DC power source. NOTE: For information about connecting to external DC power sources, see the SRX5600 Services Gateway Hardware Documentation at www.juniper.net/techpubs/ Switch on the power supply breakers to provide voltage to the DC power source cable leads.
-
Page 20: Step 7: Perform The Initial Software Configuration
SRX5600 Services Gateway Getting Started Guide Step 7: Perform the Initial Software Configuration This procedure connects the services gateway to the network but does not enable it to forward traffic. For complete information about enabling the services gateway to forward... -
Page 21: Configure System Attributes
Check the configuration for validity. [edit] admin@# commit check configuration check succeeds Optionally, display the configuration to verify that it is correct. admin@# show ## Last changed: 2008-05-07 22:43:25 UTC version "9.2I0 [builder]"; system { Copyright © 2013, Juniper Networks, Inc. - Page 22 SRX5600 Services Gateway Getting Started Guide autoinstallation; host-name henbert; root-authentication { encrypted-password "$1$oTVn2KY3$uQe4xzQCxpR2j7sKuV.Pa0"; ## SECRET-DATA login { user admin { uid 928; class super-user; authentication { encrypted-password "$1$cdOPmACd$QvreBsJkNR1EF0uurTBkE."; ## SECRET-DATA services { ssh; web-management { http { interface ge-0/0/0.0; syslog { user * { any emergency;...
- Page 23 Commit the configuration to activate it on the services gateway. [edit] admin@# commit Optionally, configure additional properties by adding the necessary configuration statements. Then commit the changes to activate them on the services gateway. [edit] admin@# commit Copyright © 2013, Juniper Networks, Inc.
-
Page 24: Safety Warnings
AC input of the services gateway. Only trained and qualified personnel should install or replace the services gateway. Perform only the procedures described in this guide or the SRX5600 Services Gateway Hardware Guide. Other services should be performed by authorized service personnel only. - Page 25 Manually installing the services gateway requires at least two people to lift the chassis. Before you lift the chassis, remove components as described in the SRX5600 Services Gateway Hardware Guide. To prevent injury, keep your back straight and lift with your legs, not your back.
-
Page 26: Requirements
SRX5600 Services Gateway Getting Started Guide SRX5600 Services Gateway Compliance Statements for EMC Requirements Canada on page 26 European Community on page 26 Japan on page 26 United States on page 26 Canada This Class A digital apparatus complies with Canadian ICES-003. -
Page 27: Srx Series Documentation And Release Notes
If the information in the latest release notes differs from the information in the documentation, follow the Junos Release Notes. To obtain the most current version of all Juniper Networks technical documentation, see the product documentation page on the Juniper Networks website at www.juniper.net/techpubs/... -
Page 28: Revision History
Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners.