Juniper SRX 5600 Installation Instructions Manual
Services gateway switch control board
Hide thumbs
Also See for SRX 5600:
- Hardware manual (536 pages) ,
- Getting started manual (37 pages) ,
- Installation instructions manual (20 pages)
Table of Contents
Advertisement
Quick Links
SRX 5600 and SRX 5800
Services Gateway
Switch Control Board
Installation Instructions
August 2008
Part Number: 530-026269-01
Revision 01
This document describes how to remove and replace a Switch Control Board (SCB)
on a Juniper Networks SRX 5600 and SRX 5800 services gateway. The illustrations
in this document show the SRX 5800 services gateway, but the instructions apply to
all SRX 5600 and SRX 5800 services gateways.
Switch Control Board .......................................................................................2
SCB Slots ...................................................................................................2
SCB Redundancy ......................................................................................3
SCB Components ......................................................................................3
SCB LEDs ..................................................................................................3
Replacing an SCB ............................................................................................4
Powering Off the Services Gateway ..........................................................4
Operating and Positioning the SCB Ejectors ..............................................5
Removing an SCB .....................................................................................5
Installing an SCB .......................................................................................6
Preventing Electrostatic Discharge Damage ....................................................8
Electrostatic Discharge Point ...........................................................................9
List of Technical Publications ........................................................................10
Requesting Technical Support .......................................................................11
Revision History ............................................................................................12
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Juniper SRX 5600
Summary of Contents for Juniper SRX 5600
-
Page 1: Table Of Contents
This document describes how to remove and replace a Switch Control Board (SCB) on a Juniper Networks SRX 5600 and SRX 5800 services gateway. The illustrations in this document show the SRX 5800 services gateway, but the instructions apply to all SRX 5600 and SRX 5800 services gateways. -
Page 2: Contents Switch Control Board
SRX 5600 and SRX 5800 Services Gateway Switch Control Board Installation Instructions Switch Control Board The Switch Control Board (SCB) provides the following functions: Powers on and powers off IOCs and SPCs Controls clocking, system resets, and booting Monitors and controls system functions, including fan speed, board power status,... -
Page 3: Scb Redundancy
Switch Control Board SCB Redundancy If two SCBs are installed in an SRX 5600 services gateway, one SCB functions as the master SCB and the other as its backup. If the master fails or is removed, the backup becomes the master. -
Page 4: Replacing An Scb
SRX 5600 and SRX 5800 Services Gateway Switch Control Board Installation Instructions Table 2: Switch Control Board LEDs Label Color State Description Green On steadily Fabric is in active mode. FABRIC ACTIVE Green On steadily SCB operates in fabric-only mode. -
Page 5: Operating And Positioning The Scb Ejectors
Ensure the long ends of the ejectors located at both the top and the bottom on an SRX 5800 services gateway, left and right on an SRX 5600 services gateway of the board are horizontal and pressed as far as possible towards the center of the board. -
Page 6: Installing An Scb
SRX 5600 and SRX 5800 Services Gateway Switch Control Board Installation Instructions Figure 2: Removing an SCB Installing an SCB To install an SCB (see Figure 3 on page 8): Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis. - Page 7 Replacing an SCB For detailed instructions on powering-on the device see the SRX 5600 Services Gateway Hardware Guide or the SRX 5800 Services Gateway Hardware Guide. To verify that the SCB is functioning normally, check the LEDs on its faceplate.
-
Page 8: Preventing Electrostatic Discharge Damage
SRX 5600 and SRX 5800 Services Gateway Switch Control Board Installation Instructions Figure 3: Installing an SCB Preventing Electrostatic Discharge Damage Many services gateway hardware components are sensitive to damage from static electricity. Some components can be impaired by voltages as low as 30 V. You can easily generate potentially damaging static voltages whenever you handle plastic or foam packing material or if you move components across plastic or carpets. -
Page 9: Electrostatic Discharge Point
Figure 5 on page 9 and Figure 6 on page 10 show the location of the ESD point on the front of each chassis. Figure 5: Front View of a Fully Configured SRX 5600 Services Gateway Chassis Electrostatic Discharge Point... -
Page 10: List Of Technical Publications
Figure 6: Front View of a Fully Configured SRX 5800 Services Gateway Chassis List of Technical Publications Table 3 on page 10 lists the hardware guides and release notes for Juniper Networks SRX–series services gateways and describes the contents of each document. All documents are available at http://www.juniper.net/techpubs/... -
Page 11: Requesting Technical Support
7 days a week, 365 days a year. Self-Help Online Tools and Resources For quick and easy problem resolution, Juniper Networks has designed an online self-service portal called the Customer Support Center (CSC) that provides you with the following features: Find CSC offerings: http://www.juniper.net/customers/support/... -
Page 12: Revision History
Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.
Need help?
Do you have a question about the SRX 5600 and is the answer not in the manual?
Questions and answers