Armstrong 4300 Installation And Operating Instructions Manual

Vertical in-line pumps

Advertisement

Commercial
pumps
Series 4300,
4360 and 4380
Vertical In-Line pumps
Ins tallation and
operat ing instructions
File No: 43.80
Date: september 14, 2012
Supersedes: 43.80
Date: september 15, 2010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4300 and is the answer not in the manual?

Questions and answers

Summary of Contents for Armstrong 4300

  • Page 1 Commercial pumps Series 4300, 4360 and 4380 Vertical In-Line pumps Ins tallation and operat ing instructions File No: 43.80 Date: september 14, 2012 Supersedes: 43.80 Date: september 15, 2010...
  • Page 3: Table Of Contents

    contents Introduction 1.1 Instructions for safe use 1. 2 Temperature 1.3 Noise levels 1. 4 Vibration levels 1.5 Storage 1.6 Uncrating 1.7 Handling large vil units 2 .0 Installation 2 .1 Location 2 . 2 Installation 2 .3 Pump piping – general 2 .
  • Page 4: Introduction

    The limits stated must not be tained. The following instructions must be strictly adhered to. exceeded without written permission from Armstrong . If clarification is needed on any point please contact Armstrong quoting the equipment serial number. 1. 2 temper ature...
  • Page 5: Vibration Levels

    @ test conditions–kW complete unit. 1.7 handling large vil units One effective way of lifting a large Series 4300 unit from the shipment pallet following uncovering the unit is to place lifting hooks through the motor lifting rings or straps around the upper part of the motor and carefully lift sufficiently to stand the pump vertically.
  • Page 6: Installation

    Fig 2.2 illustrates such an arrangement with the 2.0 installation piping supported at the ceiling and the vil unit installed with an Armstrong Suction Guide and triple function Flo-Trex valve. 2 .1 location Many very large vil pumps are installed in this manner.
  • Page 7: Pump Piping - General

    All Series 4300 pumps contain a tapped hole in the motor bracket above the discharge flange (see Fig. 2.13) for draining 2.2.7 the well. Pipe this drain hole to a floor drain to avoid overflow Fig.
  • Page 8: Alignment

    Install, at the pump suction, a straight pipe of a length trapped in the impeller. On Series 4300 any air trapped in the equivalent to 4 or 6 times its diameter; this becomes essential casing as the system is filled must be removed by the manual when handling liquids above 120°f (49°c).
  • Page 9: General Care

    Any tors, when installed in the Series 4300 flush line are very effec- possibility of the unit starting while being serviced must tive, as only the seal chamber needs cleansing, and will prolong be eliminated.
  • Page 10: System Cleanliness

    Recommended field Does not cover any damages to the equipment resulting from pressure gauge piping Flush line arrangement failure to observe the above precautions. Refer to Armstrong Flo-Trex valve Pet cock Suction guide General Terms and Warranty sheet. Contact your local (typ.)
  • Page 11 Commercial pumps Series 4300, 4360 and 4380 i n sta l la tio n & Vertical In–Line pump o p er at i ng instr uct io ns fig . 2 .3 Discharge elbow for minimum footprint. fig . 2 . 4 With additional pipe supports.
  • Page 12 & Commercial pumps Series 4300, 4360 and 4380 op era t i ng i n str u ct i on s Vertical In–Line pumps fig . 2 .7 With stanchion plates. fig . 2 .9 Horizontal mounting – 4360/4380 only to 15 hp (11 kW).
  • Page 13 Commercial pumps Series 4300, 4360 and 4380 i n sta l la tio n & Vertical In–Line pump o p er at i ng instr uct io ns fig . 2 .11 Motor lif ting hook suppor ted. fig . 2 .13 Tapped collection well.
  • Page 14 t o r o n t o 23 bertrand avenue toronto, ontario canada m1l 2p3 +1 416 755 2291 b u f f a l o 93 east avenue north tonawanda, new york u.s.a. 14120 -6594 +1 716 693 8813 b i r m i n g h a m heywood wharf, mucklow hill halesowen, west midlands...

This manual is also suitable for:

43604380

Table of Contents

Save PDF