Audiovox Rampage AV-455 Owners And Installation Manual page 9

Detachable front panel electronicall electronically-tuned am/fm/mpx radio am/fm/mpx radio with auto-reverse cassette player and quartz clock and quartz clock

Hide thumbs

Table of Contents

resume when the cassette is ejected.

NOTE: : : : : Never leave a cassette engaged in the player

NOTE

when not in use. Doing so can cause damage

t o t h e cassette and/or mechanism of the unit.

Always press the eject button and remove the

c a s s e t t e b e f o r e r e m o v i n g t h e d e t a c h a b l e f r o n t p a n e l.

TAPE MODE SELECTOR (TAPE)

During radio operation, press this button to change to

tape play if a cassette is already loaded in the unit

( TAPE IN is shown on the display panel to indicate

that a tape is loaded).

TIME/FREQUENCY SELECTOR (T/F)

Press this button to call the time display on the

incorporated quartz clock. The display will return to

the normal indication (radio frequency or "TAPE") after

5 seconds.

THEFT-DETERRENT L.E.D.

Located on the chassis behind the front panel, a light-

emitting diode (L.E.D.) will flash when the panel is

removed. The flashing light serves as a visual warning

to the would-be thief that the unit has been disabled by

removal of the front panel.

RE-SET BUTTON

A Re-Set button is located on the front of the chassis

(front panel must be removed to access the button).

The re-set circuitry is provided to protect the

microprocessor circuitry and should only be activated

under the following circumstances as it will erase the

time and pre-set memories.

1 . Switch the vehicle ignition and radio "on

2 . Momentarily press the Time/Frequency Selector button

3 . Within 5 seconds (while the time still appears on the display), press and hold the Time/Frequency Selector

and the Down Tuning (

to the correct time.

4 . When the correct time is set, release the Time/Frequency Selector. After five seconds the display will

return to the normal indication.

1 . U p o n i n i t i a l i n s t a l l a t i o n a f t e r a l l w i r i n g i s c o m p l e t e d .

2. If there is a malfunction of any of the switches on

the unit, pressing the Re-Set button may clear the

system and return to normal operation.

This button is used to release the mechanism that

holds the front panel to the chassis. To detach the

front panel, press the button so that the panel drops to

the lowered position. Grasp the panel at the middle

and p u l l i t o f f o f t h e c h a s s i s . A f t e r r e m o v i n g t h e p a n e l ,

push the metal plate back up to the vertical position.

To re-attach the panel, press it straight onto the

chassis until the mechanism locks it into place.

NOTES ON USE OF FRONT PANEL

SETTING THE

on" .

) button to adjust the hours or the Up Tuning (

FRONT PANEL RELEASE BUTTON (OPEN)

1 . Make sure the front panel is right-side-up when

attaching it to the chassis as it cannot be attached

when up-side down.

2 . Do not press very hard on the front panel when

attaching it to the chassis. No more than light to

moderate pressure should be needed.

3 . When attaching the front panel, make sure it is

centered in the chassis frame and is pressed

s t r a i g h t i n t o p o s i t i o n .

4 . When taking the front panel with you, please use

the supplied carrying case to protect the panel

from dirt and damage. Make sure there is no dust

or dirt on the electrical terminals on the back of

the panel as this could cause intermittent operation

or other malfunctions.

CLOCK

so that the time is shown on the display panel.

) button to adjust the minutes

8 8 8 8 8

128-5504

9 of 12

Table of Contents

Audiovox Rampage AV-455 Owners And Installation Manual page 9

Related Manuals for Audiovox Rampage AV-455

Related Products for Audiovox Rampage AV-455

Table of Contents