Pacvac HYDROPRO SERIES Product & Training Manual
Commercial wet and dry vacuum cleaners
Hide thumbs
Also See for HYDROPRO SERIES:
- Product & training manual (24 pages) ,
- Product & training manual (16 pages)
Related Manuals for Pacvac HYDROPRO SERIES
Summary of Contents for Pacvac HYDROPRO SERIES
- Page 1 Commercial Wet and Dry Vacuum Cleaners Support: +61 8 9479 1444 www.pacvac.com CAUTION Read the instruction manual before using the machine. Retain for future reference. Original Instructions...
-
Page 3: Table Of Contents
This manual applies to the Hydropro Series: Hydropro 21, Hydropro 36, Hydropro 76. Contents General Safety Instructions Page 2 Product Specific Safety Instructions Page 3 Symbol Definitions Page 3 Operate Right Page 4 How to Swap a Floor Tool Insert... -
Page 4: General Safety Instructions
Authorised Pacvac Service Agent in order to avoid an electric shock. The switch off immediately. power cord should only be replaced with a Pacvac 10. CAUTION Clean the water level limiting device Genuine Spare Part with the same specifications. -
Page 5: Product Specific Safety Instructions
Hydropro 21 - 41cm x 41cm x 58cm Hydropro 36 - 41cm x 41cm x 77cm Hydropro 76 - 60cm x 59cm x 105cm RETAIN THESE SAFETY INSTRUCTIONS FOR FURTHER USE. Support: +61 8 9479 1444 www.pacvac.com... -
Page 6: Operate Right
Operate Right How to vacuum easier and faster with no back strain. 1. Fit the appropriate floor tool or swap insert by sliding out the end panels on the floor tool, fitting insert and then sliding end panels back into position (Refer to diagram below). 2. -
Page 7: Work Right
• Work to the plan - long strokes for the detail clean area and short dabs for the spot cleans. Ribs Light Traffic - Spot Clean Fish Head Start Spine Heavy Traffic Areas - Tail Turn Around Detail Clean Support: +61 8 9479 1444 www.pacvac.com... -
Page 8: Safety And Maintenance Checks
Safety and Maintenance Checks DAILY Check dust bag Check all daily and replace power cords, if full. for cuts, abrasions (NOTE: Dust bag and exposed wiring. is an optional extra) Wind up power cord Check the floor tool, from machine end. wand, bent hand piece Store power cord and hose for any... -
Page 9: Troubleshooting Guide
Our products are designed and built to be functional and durable. For information on use and maintenance please read the Product & Training Manual thoroughly. Should you require servicing contact your nearest authorised Pacvac Service Centre. www.pacvac.com +61 8 9479 1444 support@pacvac.com... -
Page 10: Warranty
The following explains conditions and what to do in the event of a claim: • Pacvac will replace parts determined as faulty however this does not cover reasonable wear through normal use of any consumable parts, such as but not limited to, bags, filters, hoses, power cords, carbon brushes and floor tools etc. -
Page 11: Servicing And Warranty Notes
Servicing and Warranty Notes Support: +61 8 9479 1444 www.pacvac.com... -
Page 12: Hydropro 21 Parts Profile
Parts Profile Product Number: E21... -
Page 13: Hydropro 21 Specifications
Technical specifications, part numbers and parts profiles are subject to change without notice. This part listing is a reference for genuine Pacvac spare part orders only and may not reflect the parts used to originally build the machine at time of manufacture. -
Page 14: Hydropro 36 Parts Profile
Parts Profile Product Number: E36... -
Page 15: Hydropro 36 Specifications
Technical specifications, part numbers and parts profiles are subject to change without notice. This part listing is a reference for genuine Pacvac spare part orders only and may not reflect the parts used to originally build the machine at time of manufacture. -
Page 16: Hydropro 76 Parts Profile
Parts Profile Product Number: E76... -
Page 17: Hydropro 76 Specifications
Technical specifications, part numbers and parts profiles are subject to change without notice. This part listing is a reference for genuine Pacvac spare part orders only and may not reflect the parts used to originally build the machine at time of manufacture. -
Page 18: Hydropro 21 Accessories Parts Profile
Accessories Quote these part numbers when ordering spare parts No. Part Name Part No. Hose complete 32mm 2m E320 1a. Machine end connector 32mmE923 1b. Vacuum hose 32mm 2m UA906 1c. Bent hand piece E330 Two piece wand 32mm KC9092 Squeege floor tool 32mm E918 Combination floor tool... -
Page 19: Hydropro 36 And Hydropro 76 Accessories Parts Profile
Technical specifications, part numbers and parts profiles are subject to change without notice. This part listing is a reference for genuine Pacvac spare part orders only and may not reflect the parts used to originally build the machine at time of manufacture. - Page 20 Service & Help For service and help contact Pacvac on +61 8 9479 1444 or email support@pacvac.com Alternatively visit our website at www.pacvac.com for a list of your nearest Retailers and Service Centres. PACVAC PTY LTD Revised: August 2016 ES - M - 160831...
Need help?
Do you have a question about the HYDROPRO SERIES and is the answer not in the manual?
Questions and answers