Pacvac Hydropro Series Product & Training Manual
Commercial wet and dry vacuum cleaners
Hide thumbs
Also See for Hydropro Series:
- Product & training manual (20 pages) ,
- Product & training manual (16 pages)
Related Manuals for Pacvac Hydropro Series
Summary of Contents for Pacvac Hydropro Series
- Page 1 Commercial Wet and Dry Vacuum Cleaners Support: +61 8 9479 1444 www.pacvac.com CAUTION Read the instruction manual before using the machine. Retain for future reference. Original Instructions...
-
Page 3: Table Of Contents
This manual applies to the Hydropro Series: Hydropro 21, Hydropro 36, Hydropro 76. Contents General Safety Instructions Page 2 Product Specific Safety Instructions Page 3 Symbol Definitions Page 3 Operate Right Page 4 How to Swap a Floor Tool Insert... -
Page 4: General Safety Instructions
The power cord should only be 10. CAUTION Clean the water level limiting device replaced with a Pacvac Genuine Spare Part with the regularly and examine it for signs of damage. same specifications. 11. Remove the machine from packaging and ensure 27. -
Page 5: Product Specific Safety Instructions
Hydropro 21 - 41cm x 41cm x 58cm Hydropro 36 - 41cm x 41cm x 77cm Hydropro 76 - 60cm x 59cm x 105cm RETAIN THESE SAFETY INSTRUCTIONS FOR FURTHER USE. Support: +61 8 9479 1444 www.pacvac.com... -
Page 6: Operate Right
Operate Right How to vacuum easier and faster with no back strain. 1. Fit the appropriate floor tool or swap insert by sliding out the end panels on the floor tool, fitting insert and then sliding end panels back into position (Refer to diagram below). 2. -
Page 7: Work Right
• Work to the plan - long strokes for the detail clean area and short dabs for the spot cleans. Ribs Light Traffic - Spot Clean Fish Head Start Spine Heavy Traffic Areas - Tail Turn Around Detail Clean Support: +61 8 9479 1444 www.pacvac.com... -
Page 8: Safety And Maintenance Checks
Safety and Maintenance Checks DAILY Check dust bag Check all daily and replace power cords, if full. for cuts, abrasions (NOTE: Dust bag and exposed wiring. is an optional extra) Wind up power cord Check the floor tool, from machine end. wand, bent hand piece Store power cord and hose for any... -
Page 9: Troubleshooting
Check the machine is in good working tripped. order. If OK, reset circuit breaker or RCD. If circuit breaker or RCD trips again contact your nearest Authorised Pacvac Service and Warranty Agent. Vacuum cleaner has no/poor Dust bag full. Remove, empty and clean dust bag. suction... -
Page 10: Service Requirements
Our products are designed and built to be functional and durable. For information on use and maintenance please read the Product & Training Manual thoroughly. Should you require servicing contact your nearest Authorised Pacvac Service and Warranty Agent. www.pacvac.com +61 8 9479 1444... -
Page 11: Servicing Notes
Servicing Notes Support: +61 8 9479 1444 www.pacvac.com... -
Page 12: Warranty
The following explains conditions and what to do in the event of a claim: • Pacvac will replace parts determined as faulty however this does not cover reasonable wear through normal use of any consumable parts, such as but not limited to, bags, filters, hoses, power cords, carbon brushes and floor tools etc. -
Page 13: Warranty Notes
Warranty Notes Support: +61 8 9479 1444 www.pacvac.com... -
Page 14: Hydropro 21 Parts Profile
Parts Profile Model Number: 01HY021VW... -
Page 15: Hydropro 21 Specifications
Technical specifications, part numbers and parts profiles are subject to change without notice. This part listing is a reference for genuine Pacvac spare part orders only and may not reflect the parts used to originally build the machine at time of manufacture. -
Page 16: Hydropro 36 Parts Profile
Parts Profile Model Number: 01HY036VW... -
Page 17: Hydropro 36 Specifications
Technical specifications, part numbers and parts profiles are subject to change without notice. This part listing is a reference for genuine Pacvac spare part orders only and may not reflect the parts used to originally build the machine at time of manufacture. -
Page 18: Hydropro 76 Parts Profile
Parts Profile Model Number: 01HY076VW... - Page 19 Technical specifications, part numbers and parts profiles are subject to change without notice. This part listing is a reference for genuine Pacvac spare part orders only and may not reflect the parts used to originally build the machine at time of manufacture.
-
Page 20: Hydropro 76 Specifications
Technical specifications, part numbers and parts profiles are subject to change without notice. This part listing is a reference for genuine Pacvac spare part orders only and may not reflect the parts used to originally build the machine at time of manufacture. -
Page 21: Hydropro 21 Accessories Parts Profile
4. Floor Tool - Combination - 32mm - 270mm FLT003 5. Accessory - Dusting Brush - 32mm ACC001 6. Accessory - Crevice Tool - 32mm ACC002 7. Accessory - Upholstery Tool - 32mm ACC003 Support: +61 8 9479 1444 www.pacvac.com... -
Page 22: Hydropro 36 And Hydropro 76 Accessories Parts Profile
Accessories... - Page 23 Technical specifications, part numbers and parts profiles are subject to change without notice. This part listing is a reference for genuine Pacvac spare part orders only and may not reflect the parts used to originally build the machine at time of manufacture.
- Page 24 Service & Help For service and help contact Pacvac on +61 8 9479 1444 or email support@pacvac.com Alternatively visit our website at www.pacvac.com for a list of your nearest Authorised Distributors or Service and Warranty Agents. Revised: September 2017 PACVAC PTY LTD...
Need help?
Do you have a question about the Hydropro Series and is the answer not in the manual?
Questions and answers