Yamaha Tio1608-D Setup Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Music Mixer
  5. Tio1608-D
  6. Setup manual

Yamaha Tio1608-D Setup Manual

Tf series
Hide thumbs Also See for Tio1608-D:

Advertisement

Table of Contents

See also: Owner's Manual
TF Series with Tio1608-D
System Setup Guide
1st Edition: June 2016

Advertisement

Table of Contents
loading

Related Manuals for Yamaha Tio1608-D

Summary of Contents for Yamaha Tio1608-D

  • Page 1 TF Series with Tio1608-D System Setup Guide 1st Edition: June 2016...

  • Page 2: Table Of Contents

    Although the TF Series can be used by itself as an all-in-one console, the I/O capacity can be easily expanded by adding a Tio1608-D, allowing you to build a stagebox system with up to 40 INs/24 OUTs. The system can be set up by connecting each device with an Ethernet cable, and by making simple settings with DIP switches.

  • Page 3: Introduction

    Audinate website) and a compatible computer Connections In order to connect the TF Series and the Tio1608-D, it is necessary to install the Dante I/O card (NY64-D) on the TF Series. Connect the NY64-D (installed onto the TF Series) and the Tio1608-D in a daisy chain, using the CAT5e or CAT6 network cables.

  • Page 4: Setup Procedure

    HA Control buttons are ON (the default setting is "ON"). Note:  Up to two TF Series consoles can be connected to a single Tio1608-D at once. Make sure only up to two TF Series consoles are connected to the same network.

  • Page 5: Synchronizing The Tf Series And Tio1608-D

    TF Series & Tio1608-D Synchronizing the TF Series and Tio1608-D The TF series and Tio1608-D will automatically sync up about one minute after turning on the power switches, provided that the connections and settings have already been made. The synchronization status can be confirmed on the SLOT SETUP screen.

  • Page 6: System Examples

    "Quick Config" function. As shown in the diagram below, the I/O patches on the Tio1608-D are automatically determined by ID when the Quick Config function is used. TF Series Tio1608-D (ID: 1) INPUT 1-16 →...

  • Page 7: With Two Tio1608-D Racks

    32 INs/16 OUTs. For this system example, we recommend that you set the IDs for the two Tio1608-D racks to 1 and 2. Set the IDs of each Tio1608-D to 1 and 2 respectively, and switch the input sources for CH 1-32 on the TF Series to SLOT.
  • Page 8 TF Series & Tio1608-D the TF Series to SLOT. This will allow you to assign the input connectors from the Tio1608-D to INPUT CH 1–16. The I/O patches for each TF Series are shown below. On the TF3 and TF5, take note that the INPUT connectors 1-8 of the TF5 (or INPUT connectors 1-16 of the TF3) are patched to the “INPUT 2”...

  • Page 9: Freely Patching By Dante Controller

    Following this, connect your computer to the Dante connector on either your TF Series or the Tio1608-D with a network cable. When you wish to freely change just the output patches, turn the Quick Config function on the TF Series and Tio1608-D ON, with the TF Series "with OUTPUT" option turned OFF.

  • Page 10: Dante Slot I/P Port List

    TF Series & Tio1608-D The diagram below is an example of a stagebox system including two Tio1608-D racks, which is patched by Dante Controller. To output the SUB OUT channel to the subwoofers, turn the "with OUTPUT" option OFF, and change the output patching.

Table of Contents