1. Manuals
  2. Brands
  3. Patton electronics Manuals
  4. Modem
  5. 1092
  6. User manual

Patton electronics 1092 User Manual

Patton electronics user manual high speed, 2-wire, sync & async short range modem 1092
Hide thumbs Also See for 1092:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
USER
MANUAL
MODEL 1092
High Speed, 2-Wire,
Sync & Async
Short Range Modem
Part# 07M1092-F
Doc# 033011U, Rev. G
Revised 1/23/08
& ( 5 7 , ) , ( '
SALES OFFICE
(301) 975-1000
TECHNICAL SUPPORT
(301) 975-1007
http://www.patton.com

Advertisement

Table of Contents
loading

Related Manuals for Patton electronics 1092

Summary of Contents for Patton electronics 1092

  • Page 1 USER MANUAL MODEL 1092 High Speed, 2-Wire, Sync & Async Short Range Modem Part# 07M1092-F Doc# 033011U, Rev. G Revised 1/23/08 & ( 5 7 , ) , ( ' SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.com...

  • Page 2: Table Of Contents

    3.1 Configuring the Hardware DIP Switches 3.1.1 Configuration Switch Set “S1” 3.1.2 Configuration Switch Set “S2” 3.2 Configuring the Software Switches 3.2.1 Configuring the Local 1092 3.2.2 Configuring the Remote 1092 3.3 Power Connection 4.0 Installation ...21 4.1 Connecting the Twisted Pair Interface 4.2 Connecting the Serial Port...

  • Page 3: Warranty Information

    However, there is no guarantee that interference will not occur in a particular installation. If the Model 1092 does cause interference to radio or television reception, which can be...
  • Page 4 NOTE: Packages received without an RMA number will not be accepted. Patton Electronics' technical staff is also available to answer any questions that might arise concerning the installation or use of your Model 1092. Technical Service hours: 8AM to 5PM EST, Monday through Friday.

  • Page 5: General Information

    • LED indicators for TD, RD, CTS, CD, DTR, TM, ER and NS • Made in the U.S.A. 2.2 DESCRIPTION The Patton Model 1092 is a high speed, AC powered short range modem that is able to operate synchronously or asynchronously–full duplex–over a single twisted pair. Supporting data rates to128kbps (synchronous) or 38.4 kbps (asynchronous), the Model 1092 is capable...

  • Page 6: Configuration

    Back Figure 1. Underside of Model 1092, Showing Location of DIP Switches The two sets of DIP switches on the underside of the Model 1092 will be referred to as S1 and S2. Figure 2 shows the orientation of all DIP switches is the same with respect to “ON”...

  • Page 7: Configuration Switch Set "S1

    Response to RDL Request Switches S1-1 and S1-2: Data Rate Use Switches S1-1 and S1-2 to configure the asynchronous or synchronous data rate of the Model 1092. Each setting represents one synchronous data rate and one asynchronous data rate. S1-1...
  • Page 8 Use Switch S1-8 to allow Model 1092 to enter the Remote Digital Loopback diagnostic test when requested to do so by the far end Model 1092 For example, when Switch S1-8 is set to “ON”, it will enter RDL mode (See Section 5.3.2) when requested to do so by the remote Model 1092.

  • Page 9: Configuration Switch Set "S2

    S2-5 S2-6 Response to RDL from DTE S2-7 S2-8 Switches S2-1: 19.2 kbps Synchronous Rate Enable Use Switch S2-1 to allow the Model 1092 to operate at the 19.2 kbps synchronous data rate. S2-1 Activation Disabled Enabled *NOTE: To operate at 19.2 kbps, Set Switches S1-1 and S1-2 to the OFF position (see page 6, Switches S1-1 and S1-2).
  • Page 10 Switch S2-6: Response to RDL Request from DTE Use Switch S2-6 to determine the Model 1092 response to RDL requests from the local DTE. In the enabled setting, the 1092 responds to RDL requests from the local DTE by sending an RDL loop request to the remote Model 1092 (See Section 5.3.2).

  • Page 11: Configuring The Software Switches

    CONFIGURING THE SOFTWARE SWITCHES The Model 1092 features a menu-driven command system that allows you to configure either the local or remote 1092. Follow the instructions below to configure the Model 1092 using the software switches: Connect the serial RS-232 port of a V100 or similar DTE with terminal emulation to the EIA/TIA-561l port of the Model 1092.

  • Page 12: Configuring The Local 1092

    3.2.1 Configuring the Local 1092 To configure the LOCAL 1092, make a selection from the following MAIN MENU screen. To configure the REMOTE 1092, type [$] (Shift- 4) and refer to Section 3.2.2. MAIN MENU Option 1: Display Active Configuration Select Option 1 to display the most recent configuration of the local Model 1092 (See below).
  • Page 13 Software Switches”. Finally, select MAIN MENU Option 8 to save. MAIN MENU Option 4: Setup Software Configuration Select Option 4 toedit the software configuration of the Model 1092. To save changes after editing the software configuration, select MAIN MENU Option 5, then select “Use Software Switches” and then select...
  • Page 14 1. DTE Rate Select Option 1 in the SOFTWARE CONFIGURATION menu to select the async. or sync. DTE Rate of the Model 1092. Different DTE Rate menu screens will display for async. or sync. bit rates. The selections are shown below.
  • Page 15 (See below). Set this option as follows: Master Clock - Internal: Selection 1 allows the Model 1092 to generate an internal clock as the timing source. Master Clock - External: Selection 2 allows the Model 1092 to Derive the system clock from the locally connected DTE.
  • Page 16 5. Response to Remote Digital Loop Select Option 5 in the SOFTWARE CONFIGURATION Menu to instruct the Model 1092 to either respond or ignore the Remote Digital Loop request from the remote 1092. 6. DTE Controlled Local Line Loop Select Option 6 in the SOFTWARE CONFIGURATION Menu to instruct the Model 1092 to either respond or ignore Local Line Loop requests from the DTE.
  • Page 17 NOTE: Valid Model 1092 Handshake Statuses are listed below: 1) Handshaking - This status occurs when the 1092 is in the process of establishing a link with another 1092. 2) Data Mode - This status occurs when the 1092 successfully...
  • Page 18 If a particular test cannot be invoked, the unit displays the message: Test Mode options 2,3,7,8 and 9 require the 1092 to be in Data Mode with the remote 1092. The Model 1092 Test Modes are described below:...
  • Page 19 511 pattern generator injects intentional errors into the data stream. Remote Digital Initiates the Remote Digital Loopback test. Loop Any data sent to the remote 1092 is returned to the originating device. Remote Digital Initiates the Remote Digital Loopback test Loop and 511 and starts the internal 511 generator and detectors.

  • Page 20: Configuring The Remote 1092

    3.2.2 Configuring the Remote 1092 To configure the Remote 1092, make a selection from the following REMOTE UNIT CONFIGURATION MAIN MENU. To return to the LOCAL 1092 MAIN MENU screen, press [ESC] and refer to Section 3.2.1. REMOTE MAIN MENU Option 1: Display Remote Unit Configuration Select Option 1 to display the configuration of various parameters in the REMOTE Model 1092.
  • Page 21 REMOTE MAIN MENU Option 2: Remote Unit Configuration REMOTE MAIN MENU Option 2 allows you to edit the software configuration of the remote Model 1092. Please note that after editing the software configuration, you must select REMOTE MAIN MENU Option 4, the select “Use Software Switches” and then select MAIN MENU Option 5 to implement the most recent changes.

  • Page 22: Installation

    Model 1092: These units work in pairs. Therefore, you must have one Model 1092 (or a compatible model) at each end of a single twisted pair interface. To function properly, the Model 1092 needs one twisted pair of metallic wire.

  • Page 23: Connecting The Serial Port

    Figure 4. Installation of Model 1092 Plug-in Serial Interface Module 4.2.1 Changing QuikConnect™ Modules When you purchase a particular version of the Model 1092, it should be shipped to you with the appropriate QuikConnect™ Module already installed. If you need to install a different QuikConnect™...

  • Page 24: Connecting A "Dte" Device

    2) Hold the module with the faceplate toward you and align the module with the guide slots in the rear panel of the Model 1092. 3) While keeping the module’s faceplate parallel with the Model 1092 rear panel, slide the module straight in–so that the card...

  • Page 25: Configuring The X.21 Quikconnect™ Module

    Reinstall the module according to the instructions in Section 4.2.1. 4.3 POWER CONNECTION The Model 1092 is available with three power supply options: Standard AC Power Supply option (Model 1092, no suffix) is switchable between 100 and 253 VAC and is available with a variety of domestic and international power cords.

  • Page 26: Connecting To A Dc Power Source

    Manual for further instructions. WARNING! There are no user-serviceable parts in the power supply section of the Model 1092. Voltage setting changes and fuse replacement should only be performed by qualified service personnel. Contact Patton Electronics Technical support at (301) 975-1007, via our website at http://www.patton.com, or by e-mail at support@patton.com,...

  • Page 27: Operation

    LED status monitors, and using the built-in loopback test modes. 5.1 POWER-UP To apply power to the Model 1092, first be sure that you have read Section 4.3, and that the unit is connected to the appropriate power source. Then power-up the unit using the rear power switch.

  • Page 28: Test Modes

    The Local Line Loopback (LLB) test checks the operation of the local Model 1092, and is performed separately on each unit. Any data sent to the local Model 1092 in this test mode will be echoed (returned) back to the user device. (See Figure 6, below.) For example, characters typed on the keyboard of a terminal will appear on the terminal screen.

  • Page 29: Using Remote Digital Loopback (Rdl)

    1. Locate the “511/511E” toggle switch on the front panel of the 1092 and move it UP. This activates the V.52 BER test mode and transmits a “511” test pattern into the loop. If any errors are present, the local modem’s red “ER” LED will blink sporadically.
  • Page 30 If the test is working properly, the local modem's red “ER” LED will glow. A successful “511/E” test will confirm that the link is in place, and that the Model 1092’s built-in “511” generator and detector are working properly.

  • Page 31: Appendix A - Specifications

    PATTON MODEL 1092 SPECIFICATIONS Transmission Format: Synchronous or asynchronous Transmission Line: Single unconditioned twisted pair Clocking: Internal, external or receive loopback Distance: Distance, max, all data rates: 10.1 miles (16.4km) on 19 AWG (0.9mm) wire 7.2 miles (11.5 km) on 22 AWG (0.64mm) wire 5.0 (8 km) on 24 AWG (0.5mm) wire...

  • Page 32: Appendix B - Factory Replacement Parts And Accessories

    APPENDIX B PATTON MODEL 1092 FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model # Description IM1/A...V.24 with DB25F IM1/B ...RS422/RS530 with DB25F IM1/C...V.35 with M34F IM1/D...X.21 with DB15F IM1/E ...V.35 with DB25F IM1/F ...G.703 with RJ45 0805US ...American Power Cord 0805EUR...European Power Cord CEE 7 0805UK ...United Kingdom Power Cord...
  • Page 33 APPENDIX C PATTON MODEL 1092 INTERFACE PIN ASSIGNMENT RS-232, RS-530 Interface Pin Description (DB-25 Female Connector) (DCE Configuration) Pin # FG (Frame Ground) TD (Transmit Data) RD (Receive Data) RTS (Request to Send) CTS (Clear to Send) DSR (Data Set Ready)
  • Page 34 APPENDIX C PATTON MODEL 1092 INTERFACE PIN ASSIGNMENT (Continued) V.35 Interface (M/34F Female Connector) (DCE Configuration) Pin # B ...SGND C ...RTS D ...CTS E ...DSR F...CD H ...DTR L...LLB (Local Line Loop) M ...TM N ...RDL P ...TD R ...RD S ...TD/...
  • Page 35 APPENDIX C PATTON MODEL 1092 INTERFACE PIN ASSIGNMENT (Continued) X.21 Interface (DB-15 Female Connector) (DTE /DCE Configuration) Pin # 1 ... . Frame Ground 2 ... . T (Transmit Data-A) 3 .
  • Page 36 PATTON MODEL 1092 Pin Out Control Port The 1092 control port is an 8 position connector, compliant with EIA/TIA-561. Pin Function Ground Receive data (to DTE) Transmit data (from DTE) APPENDIX D RJ45 Pin No.
  • Page 37 Dear Valued Customer, Thank you for purchasing Patton Electronics products! We do appreciate your business. I trust that you find this user manual helpful. We manufacture one of the widest selections of data communications products in the world including CSU/DSU's, network termination units, powered and self-powered short range modems, fiber optic modems, interface converters, baluns, electronic data switches, data-line surge protectors, multiplexers, transceivers, hubs, print servers and much more.

Table of Contents