Download Print this page

ON Semiconductor CAT24C01 Manual

1-kb, 2-kb, 4-kb, 8-kb and 16-kb i2c cmos serial eeprom

Advertisement

Quick Links

CAT24C01, CAT24C02,
CAT24C04, CAT24C08,
CAT24C16
1-Kb, 2-Kb, 4-Kb, 8-Kb and
2
16-Kb I
C CMOS Serial
EEPROM
Description
The CAT24C01/02/04/08/16 are 1−Kb, 2−Kb, 4−Kb, 8−Kb and
16−Kb respectively CMOS Serial EEPROM devices organized
internally as 8/16/32/64 and 128 pages respectively of 16 bytes each.
All devices support both the Standard (100 kHz) as well as Fast
2
(400 kHz) I
C protocol.
Data is written by providing a starting address, then loading 1 to 16
contiguous bytes into a Page Write Buffer, and then writing all data to
non−volatile memory in one internal write cycle. Data is read by
providing a starting address and then shifting out data serially while
automatically incrementing the internal address count.
External address pins make it possible to address up to eight
CAT24C01 or CAT24C02, four CAT24C04, two CAT24C08 and one
CAT24C16 device on the same bus.
Features
Supports Standard and Fast I
1.7 V to 5.5 V Supply Voltage Range
16−Byte Page Write Buffer
Hardware Write Protection for Entire Memory
Schmitt Triggers and Noise Suppression Filters on I
(SCL and SDA)
Low power CMOS Technology
More than 1,000,000 Program/Erase Cycles
100 Year Data Retention
Industrial and Extended Temperature Range
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
PIN CONFIGURATION
CAT24C__
16 / 08 / 04 / 02 / 01
NC /
NC NC
/
/
/
A
A
0
0
/
/
/
/
NC NC
A
A
A
1
1
1
/
/
/
/
NC
A
A
A
A
2
2
2
2
V
SS
PDIP (L), SOIC (W), TSSOP (Y), MSOP (Z),
TDFN, (VP2)*, UDFN−EP (HU4) (Top View)
* The TDFN (VP2) package is not recommended for new designs.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 19 of this data sheet.
© Semiconductor Components Industries, LLC, 2013
February, 2013 − Rev. 26
2
C Protocol
2
C Bus Inputs
V
8
1
CC
WP
2
7
SCL
3
6
SDA
4
5
CASE 646AA
MSOP−8
Z SUFFIX
CASE 846AD
TSSOP−8
Y SUFFIX
CASE 948AL
W SUFFIX
CASE 751BD
TDFN−8*
VP2 SUFFIX
CASE 511AK
PIN CONFIGURATIONS
SCL
V
SS
SDA
TSOT−23 (TD), TSOP−5** (TS) (Top View)
** TSOP are available for the CAT24C02 only.
1
Pin 1
A
V
CC
B
SCL
WLCSP−4***
*** WLCSP are available for the CAT24C04,
CAT24C08 and CAT24C16 only.
TOP MARKING FOR WLCSP
Pin 1
X
Y M
WLCSP−4
Y = Production Year (Last Digit)
M = Production Month (1−9, O, N, D)
1
http://onsemi.com
UDFN8−EP
PDIP−8
HU4 SUFFIX
L SUFFIX
CASE 517AZ
TSOT−23
TD SUFFIX
CASE 419AE
TSOP−5**
TS SUFFIX
CASE 483
SOIC−8
WLCSP−4***
C4A SUFFIX
CASE 567DC
WLCSP−5***
C5A SUFFIX
CASE 567DD
5
WP
1
2
3
4
V
CC
2
1
2
Pin 1
V
V
V
SS
CC
SDA
SDA
WP
SCL
WLCSP−5***
(Top Views)
(Ball Down)
X = Specific Device
X =
Code
Y M
4 = 24C04
8 = 24C08
WLCSP−5
6 = 24C16
Publication Order Number:
CAT24C01/D
3
A
SS
B
C
Pin 1
X

Advertisement

loading

Summary of Contents for ON Semiconductor CAT24C01

  • Page 1 C4A SUFFIX W SUFFIX External address pins make it possible to address up to eight CASE 567DC CASE 751BD CAT24C01 or CAT24C02, four CAT24C04, two CAT24C08 and one TDFN−8* WLCSP−5*** CAT24C16 device on the same bus. VP2 SUFFIX C5A SUFFIX...
  • Page 2 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 Table 1. PIN FUNCTION † Pin Name Function A0, A1, A2 Device Address Input Serial Data Input/Output Serial Clock Input CAT24Cxx Write Protect Input Power Supply Ground No Connect †The exposed pad for the TDFN/UDFN packages can be left floating or connected to Ground.
  • Page 3 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 Table 5. PIN IMPEDANCE CHARACTERISTICS = 1.8 V to 5.5 V, T = −40°C to +125°C and V = 1.7 V to 5.5 V, T = −40°C to +85°C, unless otherwise specified.) Symbol Parameter Conditions...
  • Page 4 HIGH. NOTE: The I/O pins of CAT24Cxx do not obstruct the SCL *For common features, the CAT24C01/02/04/08/16 will be referred to as CAT24Cxx. and SDA lines if the VCC supply is switched off. During power−up, the SCL and SDA pins (connected with pull−up...
  • Page 5 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 START STOP CONDITION CONDITION Figure 2. Start/Stop Timing CAT24C01 and CAT24C02 CAT24C04 CAT24C08 CAT24C16 Figure 3. Slave Address Bits BUS RELEASE DELAY (TRANSMITTER) BUS RELEASE DELAY (RECEIVER) SCL FROM MASTER DATA OUTPUT FROM TRANSMITTER DATA OUTPUT...
  • Page 6: Write Operations

    CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 WRITE OPERATIONS Byte Write sixteen bytes are received and the STOP condition has been In Byte Write mode, the Master sends the START sent by the Master, the internal Write cycle begins. At this condition and the Slave address with the R/W bit set to zero point all received data is written to the CAT24Cxx in a single to the Slave.
  • Page 7 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 Byte n STOP START ADDRESS CONDITION CONDITION Figure 7. Write Cycle Timing BUS ACTIVITY: DATA DATA DATA ADDRESS SLAVE BYTE BYTE BYTE MASTER ADDRESS BYTE SLAVE n = 1 P v 15 Figure 8. Page Write Sequence...
  • Page 8: Read Operations

    (rather than end of page). In by sending the START condition, slave address and byte the CAT24C01, the internal address count will not wrap address of the location it wishes to read. After the around at the end of the 128 byte memory space.
  • Page 9: Top View

    CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 PACKAGE DIMENSIONS PDIP−8, 300 mils CASE 646AA ISSUE A SYMBOL 5.33 0.38 2.92 3.30 4.95 0.36 0.46 0.56 1.14 1.52 1.78 0.20 0.25 0.36 9.02 9.27 10.16 7.62 7.87 8.25 6.10 6.35 7.11 2.54 BSC 7.87...
  • Page 10 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD ISSUE O SYMBOL 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 5.80 6.20 3.80 4.00 1.27 BSC 0.25 0.50 0.40 1.27 PIN # 1 0º...
  • Page 11 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL ISSUE O SYMBOL 1.20 0.05 0.15 0.80 0.90 1.05 0.19 0.30 0.09 0.20 2.90 3.00 3.10 6.30 6.40 6.50 4.30 4.40 4.50 0.65 BSC 1.00 REF 0.50 0.60 0.75 0º...
  • Page 12 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 PACKAGE DIMENSIONS MSOP 8, 3x3 CASE 846AD ISSUE O SYMBOL 1.10 0.05 0.10 0.15 0.75 0.85 0.95 0.22 0.38 0.13 0.23 2.90 3.00 3.10 4.80 4.90 5.00 2.90 3.00 3.10 0.65 BSC 0.40 0.60 0.80 0.95 REF...
  • Page 13 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 PACKAGE DIMENSIONS TDFN8, 2x3 CASE 511AK ISSUE A PIN#1 IDENTIFICATION PIN#1 INDEX AREA TOP VIEW SIDE VIEW BOTTOM VIEW SYMBOL 0.70 0.75 0.80 0.00 0.02 0.05 0.45 0.55 0.65 0.20 REF 0.20 0.25 0.30 1.90 2.00...
  • Page 14 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 PACKAGE DIMENSIONS TSOT−23, 5 LEAD CASE 419AE ISSUE O SYMBOL 1.00 0.01 0.05 0.10 0.80 0.87 0.90 0.30 0.45 0.12 0.15 0.20 2.90 BSC 2.80 BSC 1.60 BSC 0.95 TYP 0.30 0.40 0.50 0.60 REF 0.25 BSC...
  • Page 15 0.20 0.60 1.25 1.55 2.50 3.00 SOLDERING FOOTPRINT* 0.074 0.95 0.037 0.094 0.039 0.028 SCALE 10:1 inches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com...
  • Page 16 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 PACKAGE DIMENSIONS UDFN8, 2x3 EXTENDED PAD CASE 517AZ ISSUE O DAP SIZE 1.8 x 1.8 PIN #1 IDENTIFICATION PIN #1 INDEX AREA TOP VIEW SIDE VIEW BOTTOM VIEW SYMBOL 0.45 0.50 0.55 0.00 0.02 0.05 0.127 REF...
  • Page 17: Bottom View

    RECOMMENDED SOLDERING FOOTPRINT* PACKAGE 0.10 OUTLINE NOTE 5 0.40 BOTTOM VIEW 0.18 PITCH 0.40 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com...
  • Page 18 PACKAGE 0.10 OUTLINE NOTE 4 PIN A1 REFERENCE BOTTOM VIEW 0.52 0.16 PITCH 0.30 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com...
  • Page 19 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 Ordering Information CAT24C01 Ordering Information Specific Package Temperature Lead Device Marking Type Range (Note 9) Finish Device Order Number Shipping CAT24C01TDI−GT3 TSOT−23−5 Industrial NiPdAu Tape & Reel, 3,000 Units / Reel CAT24C01VP2I−GT3* TDFN−8 Industrial NiPdAu Tape &...
  • Page 20 CAT24C01, CAT24C02, CAT24C04, CAT24C08, CAT24C16 CAT24C04 Ordering Information Specific Package Temperature Lead Device Marking Type Range (Note 12) Finish Device Order Number Shipping CAT24C04WI−G 24C04K SOIC−8 Industrial NiPdAu Tube, 100 Units / Tube CAT24C04WI−GT3 24C04K SOIC−8 Industrial NiPdAu Tape & Reel, 3,000 Units / Reel CAT24C04WE−GT3...
  • Page 21 15. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. 16. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device Nomenclature document, TND310/D, available at www.onsemi.com * The TDFN (VP2) package is not recommended for new designs.

This manual is also suitable for:

Cat24c04Cat24c02Cat24c16Cat24c08