Assembly And Adjustment; Using An Extension Cable - DeWalt D28111 Instructions Manual

E N G L I S H
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm 2 .
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
Conductor size (mm 2 )
0.75
1.00
1.50
2.50
4.00
Voltage Amperes
115 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
28
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5 15 25 30 45
Cable rating (Amperes)
6 6 6 6
6 6 6 6 15
6 6 10 15 20
10 10 15 20 20
15 15 20 25 25
20 20 25 -
6 6 6 6
6 6 6 6
6 6 6 6 10
10 10 10 10 15
15 15 15 15 20
20 20 20 20 25

Assembly and adjustment

Mounting and removing the guard (fig. B1 & B2)
D28111/D28139 - Guard with fixing screw (fig. B1)
• Place the angle grinder on a table, spindle up.
• Align the lugs (5) with the notches (6).
• Press the guard down and rotate it to the
. required position.
• Securely tighten the screw (7).
• To remove the guard, slacken the screw.
D28113(K)/D28130/D28132/D28134/D28135(K)/
D28141 - Keyless guard (fig. B2)
• Place the angle grinder on a table, spindle up.
• Release the clamping lock (8) and hold the guard
(3) over the tool as shown.
• Align the lugs (5) with the notches (6).
• Press the guard down and rotate it to the
required position.
• If required, increase the clamping force by
tightening the screw (9).
• Tighten the clamping lock.
• To remove the guard, release the clamping lock.
60
Fitting and removing a grinding or cutting disc
6 10
(fig. C1 & C2)
15
• Place the tool on a table, guard up.
20
• Fit the inner flange (10) correctly onto the spindle
25
(11) (fig. C1).
-
• Place the disc (12) on the flange (10). When
- -
fitting a disc with a raised center, make sure that
6 6
the raised centre (13) is facing the flange (10).
6 6
• Screw the outer flange (14) onto the spindle (11)
15
(fig. C2):
15
– the ring on the flange (14) must face towards
20
the disc when fitting a grinding disc (A);
-
– the ring on the flange (14) must face away from
the disc when fitting a cutting disc (B).
Prior to assembly and adjustment always
unplug the tool.
Never use the tool without the guard in
place.
Never use the tool without the guard in
place.