Using An Extension Cable; Assembly And Adjustment - DeWalt D28410 User Manual

Always ensure that the cable clamp is
correctly and securely fi tted to the sheath
of the cable.

Using an extension cable

If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm 2 .
When using a cable reel, always unwind the cable
completely.
Also refer to the following table.
Conductor size (mm ) Cable rating (Amperes)
2
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
7.5 15
Voltage Amperes Cable rating (Amperes)
115 0 - 2.0 6
2.1 - 3.4 6
3.5 - 5.0 6
5.1 - 7.0 10 10
7.1 - 12.0 15 15
12.1 - 20.0 20 20
230 0 - 2.0 6
2.1 - 3.4 6
3.5 - 5.0 6
5.1 - 7.0 10 10
7.1 - 12.0 15 15
12.1 - 20.0 20 20

Assembly and adjustment

Prior to assembly and adjustment always
unplug the tool.
Mounting and removing the guard (fi g. B)
• Place the angle grinder on a table, spindle up.
• Release the clamping lock (6) and hold the guard
(4) over the tool as shown.
• Align the lugs (7) with the notches (8).
• Press the guard down and rotate it to the
required posiiton.
Fitting and removing a grinding or cutting disc
(fi g. C1 - C3)
Cable length (m)
25 30 45 60
6 6 6 6 10
6 6 6 15 15
6 10 15 20 20
15 20 20 25
20 25 25 -
25 - - -
6 6 6 6 6
6 6 6 6 6
6 6 6 10 15
10 10 15 15
15 15 20 20
20 20 25 -
Mounting the side handle (fi g. D1 & D2)
D28432C - Rotating the main handle (fi g. E1 & E2)
The rotary handle facilitates a more comfortable
handling in cutting applications with the side handle
mounted in the top hole.
The rotary handle has locations at 30°, 60° and 90°
both left and right.
• If required, increase the clamping force by
tightening the screw (9).
• Tighten the clamping lock.
• To remove the guard, release the clamping lock.
Never use the tool without the guard in
place.
• Place the tool on a table, guard up.
• Fit the inner fl ange (10) correctly onto the spindle
(11) (fi g. C1).
• Place the disc (12) on the fl ange (10) (fi g. C2).
When fi tting a disc with a raised center, make
sure that the raised centre (13) is facing the
fl ange (10).
• Screw the outer fl ange (14) onto the spindle (11)
(fi g. C3):
- the ring on the fl ange (14) must face towards
the disc when fi tting a grinding disc (A);
- the ring on the fl ange (14) must face away from
the disc when fi tting a cutting disc (B).
• Press the spindle lock (3) and rotate the spindle
(11) until it locks in position (fi g. C2)
• Tighten the fl ange (14) with the two-pin spanner
supplied.
• Release the spindle lock.
• To remove the disc, loosen the fl ange (14) with
the two-pin spanner.
Do not use a damaged disc.
• For grinding, screw the side handle (5) tightly into
one of the holes (15) on either side of the gear
case (fi g. D1).
• For cutting, screw the side handle (5) tightly into
the top hole (16) or into one of the holes (17) on
either side of the gear case (fi g. D2).
E N G L I S H
9