Service Alignment Mode (Sam) - Philips L01.1E Service Manual

GB 14 5.
After entering SDM, the following screen is visible, with SDM
at the upper right side for recognition.
A A A B C D E E X . Y
E R R X X X X X X
M E N U
M a i n
• P i c t u r e
• S o u n d
• F e a t u r e s
• I n s t a l l
Figure 5-3
How to navigate
Use one of the following methods:
• When you press the MENU button on the remote control,
the set will switch between the SDM and the normal user
menu (with the SDM mode still active in the background).
Return to the SDM screen with the OSD / STATUS
button.
• When you press the OSD / STATUS button on the
remote control, the menu will show or hide the error
buffer. This feature is available to prevent interference
during waveform measurements.
• On the TV, press and hold the 'VOLUME down' and
press the 'CHANNEL down' for a few seconds, to switch
from SDM to SAM and reverse.
How to exit
Switch the set to STANDBY by pressing the power button on
the remote control transmitter (if you switch the set 'off' by
removing the Mains power, the set will return in SDM when
Mains power is re-applied). The error buffer is cleared.
L01.1E Service Modes, Error Codes and Fault Finding
S D M
X X X X
S D M
^
> B r i g h t n e s s
C o l o u r
C o n t r a s t
S h a r p n e s s
C o l o u r T e m p
S t o r e
v
O S D / S T A T U S
S D M
CL 16532020_060.pdf
220501
5.2.2

Service Alignment Mode (SAM)

Purpose
• To perform alignments.
• To change option settings.
• To display / clear the error code buffer.
Specifications
• Operation hours counter.
• Software version.
• Option settings.
• Error buffer reading and erasing.
• Software alignments.
How to enter
Use one of the following methods:
• Use a standard customer RC-transmitter and key in the
code '062596' directly followed by the OSD / STATUS
button or
• Via ComPair.
The following screen is visible, with SAM at the upper right
side for recognition.
L L L L A A A B C D
E R R X X X X X X
X X X X X X X X X
C L E A R
O P T I O N S
A K B
T U N E R
W H I T E T O N E
G E O M E T R Y
A U D I O
Figure 5-4
1. LLLL This is the operation hours counter. It counts the
normal operation hours, not the standby hours.
2. AAABCD-X.Y This is the software identification of the
main micro controller:
• A = the project name (L01).
• B = the region: E = Europe, A = Asia Pacific, U =
NAFTA, L = LATAM.
• C = the software diversity: D= DVD, F= full TXT, M=
mono, T= 1 page TXT.
• D = the language cluster number.
• X = the main software version number.
• Y = the sub software version number.
3. SAM Indication of the actual mode.
4. Error buffer Five errors possible.
5. Option bytes Seven codes possible.
6. Clear Erase the contents of the error buffer. Select the
CLEAR menu item and press the CURSOR RIGHT key.
The content of the error buffer is cleared.
7. Options To set the Option Bytes. See chapter 8.3.1 for
a detailed description.
8. AKB Disable (0) or enable (1) the 'black current loop'
(AKB = Auto Kine Bias).
9. Tuner To align the Tuner. See chapter 8.3.2 for a
detailed description.
10. White Tone To align the White Tone. See chapter 8.3.3
for a detailed description.
11. Geometry To align the Geometry. See chapter 8.3.4 for
a detailed description.
12. Audio To align the Audio. See chapter 8.3.5 for a
detailed description.
How to navigate
Use one of the following methods:
X . Y S A M
X X X X
X X X X X X X X X X X X
C L E A R ?
>
0 / 1
>
>
>
>
CL 16532020_061.eps
150401