Table of Contents
Advertisement
EN 14
5.
TPM15.1E LA
Table 5-1 SAM mode overview
Main Menu
Sub-menu 1
System Information
Op Hour
Main SW ID
ERR
OP1
OP2
Clear Codes
Press [OK] to clean the Error Codes
immediately
Options
OP#1-OP#8
Alignments
Warm
Normal
Cool
Store
NVM editor
NVM editor
Service Data
Upload to USB
Channel List
NVM Copy
Readable Info
EDID Copy
Download from USB Channel List
NVM Copy
EDID Copy
Initialize NVM
Press [OK] to Initialize NVM
immediately
Dealer Options
Set Virgin mode
Store
How to Navigate
•
In the SAM menu, select menu items with the UP/DOWN
keys on the remote control transmitter. The selected item
will be indicated. When not all menu items fit on the screen,
use the UP/DOWN keys to display the next/previous menu
items.
•
With the "LEFT/RIGHT" keys, it is possible to:
–
(De) activate the selected menu item.
–
(De) activate the selected sub menu.
–
Change the value of the selected menu item.
•
When you press the MENU button once while in top level
SAM, the set will switch to the normal user menu (with the
SAM mode still active in the background).
How to Store SAM Settings
To store the settings changed in SAM mode (except the
RGB Align settings), leave the top level SAM menu by using
the POWER button on the remote control transmitter or the
television set. The mentioned exceptions must be stored
separately via the STORE button.
How to Exit SAM
Use one of the following methods:
•
Switch the set to STANDBY by pressing the mains button
on the remote control transmitter or the television set.
•
Via a standard RC-transmitter, key in "00" sequence.
Note: When the TV is switched "off" by a power interrupt while
in SAM, the TV will show up in "normal operation mode" as
soon as the power is supplied again. The error buffer will not be
cleared.
2015-Jun-12
Service Modes, Error Codes, and Fault Finding
Sub-menu 2
Description
e.g. 00011
This represents the life timer. The timer counts normal operation hours, but does not
count Stand-by hours.
e.g. "TPN14E_010.001.004.001"
See paragraph
definition.
e.g. "000 000 000 000 000"
Shows all errors detected since the last time the buffer was erased. Five errors
possible.
e.g. "000 224 032 000 038 192 192
Used to read-out the option bytes. See paragraph
015"
Alignments section for a detailed description. Ten codes are possible.
e.g. "159 255 127 061 011003 000
000"
Erases the contents of the error buffer. Select this menu item and press the MENU
RIGHT key on the remote control. The content of the error buffer is cleared.
e.g. "032"
Option code
R Gain
To align the White Tone. See
paragraph
G Gain
description
B Gain
R Gain
G Gain
B Gain
R Gain
G Gain
B Gain
Store the RGB value
NVM-editor will function as in the past: Address and Value
field is a decimal value via digit entry
Edit and display the applicable service data by using the displayed key pad
To upload several settings from the TV to an USB stick
To download several settings from the USB stick to the TV
To initialize a (corrupted) NVM. Be careful, this will erase all settings.
Virgin mode:Off
Set Virgin mode
Press [OK] to store virgin mode
Store the virgin mode in the address
immediately
5.2.3
back to
div.table
Software Identification, Version, and Cluster
6.3 Software Alignments
in the Alignments section for a detailed
Contents of the Factory mode:
Purpose
•
To perform extended alignments.
Specifications
•
Displaying and or changing Panel ID information.
•
Displaying and or changing Tuner ID information.
•
Error buffer clearing.
•
Various software alignment settings.
•
Testpattern displaying.
•
Public Broadcasting Service password Reset.
•
etc.
How to Activate the Factory mode
To activate the Factory mode, use the following method:
•
Press the following key sequence on the remote control
transmitter: from the "menu/home" press "1999", directly
followed by the "Back/Return" button. Do not allow the
display to time out between entries while keying the
sequence.
After entering the Factory mode, the following items are
displayed,
for the software name
6.4 Option Settings
in the
- Quick Links:
- Service Modes, Error Codes, and Fault...
Hide quick links:
Advertisement
Table of Contents
