Page 4
GB 4 L01.1E Technical Specifications, Connections and Chassis Overview Chassis Overview TOP CONTROL PANEL SIDE AV PANEL + HEADPHONE CRT PANEL FRONT INTERFACE POWER SUPPLY LINE DEFLECTION FRAME DEFLECTION TUNER IF VIDEO + SOUND IF SYNCHRONISATION MAIN CHASSIS CONTROL (µP)
Page 5
Safety & Maintenance Instructions, Warnings, and Notes L01.1E GB 5 2. Safety & Maintenance Instructions, Warnings, and Notes Safety Instructions For Repairs Warnings Safety regulations require that during a repair: • In order to prevent damage to ICs and transistors, avoid •...
Page 11
Mechanical Instructions L01.1E GB 11 4. Mechanical Instructions Note: Figures below can deviate slightly from the actual situation, due to the different set executions. Main panel with bracket. 1. Disconnect the strain relief of the Mains cord. 2. Disconnect the degaussing coil by removing the cable Rear Cover Removal from (red) connector 0201 [1].
Page 12
GB 12 L01.1E Mechanical Instructions Side I/O Panel Removal (if present) 1. Remove the complete Side I/O assembly, after unscrewing the 2 fixation screws [1]. 2. Release the two fixation clamps [2] and lift the board out of the bracket.
Service Modes, Error Codes and Fault Finding L01.1E GB 13 5. Service Modes, Error Codes and Fault Finding Index of this chapter: 5.2.1 Service Default Mode (SDM) 1. Test points. 2. Service Modes. Purpose 3. Problems and Solving Tips (related to CSM).
Page 14
GB 14 L01.1E Service Modes, Error Codes and Fault Finding After entering SDM, the following screen is visible, with SDM 5.2.2 Service Alignment Mode (SAM) at the upper right side for recognition. Purpose • To perform alignments. • To change option settings.
Page 15
Service Modes, Error Codes and Fault Finding L01.1E GB 15 • In SAM, select menu items with the CURSOR UP/DOWN 6. Indicates if the sleep timer is enabled. key on the remote control transmitter. The selected item 7. Indicates if the V-chip feature is enabled.
Page 16
Click on the ‘Schematic’ hyperlink to automatically show 5.4.1 Introduction the position of the highlighted capacitor. ComPair (Computer Aided Repair) is a service tool for Philips 5.4.3 How To Connect Consumer Electronics products. ComPair is a further development on the European DST (service remote control), 1.
Page 17
Service Modes, Error Codes and Fault Finding L01.1E GB 17 • On screen via the SAM (only if you have a picture). Examples: – ERROR: 0 0 0 0 0 : No errors detected – ERROR: 6 0 0 0 0 : Error code 6 is the last and only detected error –...
GB 18 L01.1E Service Modes, Error Codes and Fault Finding The Blinking LED Procedure the same time, measure the ‘+8V’. If this voltage is missing, check transistor TS7480. • Set is non-stop in hiccup mode Set is in over current Via this procedure, you can make the contents of the error mode;...
Page 19
Block Diagram, Testpoints, I2C and Supply Voltage Overview L01.1E 6. Block Diagram, Testpoints, I C and Supply Voltage Overview Block Diagram REAR I/O SCART AUDIO/VIDEO AUDIO AMPLIFIER FRONT CONTROL CONTROL +3.3V +3.3V SOURCE SWITCHING FOR MONO SETS MONO/ 7943 7801...
Page 20
Block Diagram, Testpoints, I2C and Supply Voltage Overview L01.1E Testpoint Overview Main Panel Copper Track side AUDIO OUTPUT 7901 OR 7902 2V / div DC 1V / div DC 50V / div DC TV-PROC. 20us / div 10us / div 10us / div P1 = "$"...
Page 21
Block Diagram, Testpoints, I2C and Supply Voltage Overview L01.1E C and Supply Voltage Diagram POWER SUPPLY SCAVEM LINE DEFLECTION 5445 3362 ANODE CRT +13Va FOCUS FOCUS 5500 : 6500 6560 FOCUS CRT 5560 5564 5561 MAIN SUPPLY 3487 0231 5451...
Page 22
Schematics and PWB’s L01.1E 7. Schematics and PWB’s Large Signal Panel: Power supply 0211 C1 0282 F11 2502 B6 2507 D7 2520 F2 2526 D2 2559 D9 2564 C9 2569 G10 3503 B6 3509 B5 3522 E5 3527 E7 3532 D6...
Page 26
Schematics and PWB’s L01.1E Large Signal Panel: Tuner I/F 0265 A4 Diversity Table A4 TUNER IF 0283 B2 0285 B2 1000 A3 FM-RADIO ANTENNA 1002 D7 0265 1003 E7 VT_Supply VlotAux+5V 1004 E7 2001 C3 FOR ITV ONLY 2002 C3...
Page 27
Schematics and PWB’s L01.1E Large Signal Panel: Video IF + Sound IF 0243 C6 4218 F9 0248 C2 5201 D7 0249 B2 5202 A8 VIDEO IF + SOUND IF 0266 E11 5204 F2 0276 C2 5205 G2 3220 9618 1200 E7...
Page 33
Schematics and PWB’s L01.1E Large Signal Panel: Front I/O + Front Control + Headphone 0214 F9 0215 C4 0218-A C2 0218-B C2 FRONT IO + FRONT CONTROL + HEADPHONE 0218-C B2 0219 D4 0232 F5 DIVERSITY TABLE SEE PAGE 24...
Page 34
Schematics and PWB’s L01.1E Large Signal Panel: Rear I/O SCART 0224-A F11 3120 F4 0224-B G11 3121 G3 0227 A7 3122 F4 0229 E7 3131 A9 REAR I/O SCART 0235-A A1 3132 B8 TO 0227 OF TO 0227 OF 0235-B A11...
Page 44
Schematics and PWB’s L01.1E Layout CRT and SCAVEM Panel (Top View) Layout CRT and SCAVEM (Bottom View)
Page 45
Schematics and PWB’s L01.1E Side AV + HP Panel Layout Side AV + HP Panel (Top View) 0232 E5 0250-A C2 0250-B D2 0250-C B2 SIDE AV + HP PANEL 0251 A5 0254 E2 0255 E5 0277-A B1 0277-B D1...
Page 46
Schematics and PWB’s L01.1E Side AV Panel + Headphone Layout Side AV Panel + Headphone (Top View) 0232 D4 0250-A B2 SIDE AV PANEL & HEADPHONE 0250-B C2 0250-C A2 0251 B5 0252 B2 0253 A5 0254 D2 0255 D5...
Page 47
Schematics and PWB’s L01.1E Top Control Panel (RF) Layout Top Control Panel (RF) 0215 A1 1091 B2 1092 B3 1091 A1 1093 B3 TOP CONTROL PANEL (RF) 1092 B1 1094 C3 2010 B1 1093 A2 3091 A1 1094 A1 3092 A2...
Page 48
Schematics and PWB’s L01.1E Top Control Panel (FSQ) Layout Top Control Panel (FSQ) 0215 A2 1091 A2 TOP CONTROL PANEL (FSQ) 1092 A1 1093 A2 1094 A1 6091 A2 0215 TO 0239 3091 3092 3093 3094 3095 560R 390R 560R...
Page 49
Alignments L01.1E GB 49 8. Alignments Index of this chapter: – BRIGHTNESS to minimum (OSD just visible in a 1. General Alignment Conditions dark room). 2. Hardware Alignments 5. Return to the SAM via the MENU key. 3. Software Alignments and Settings 6.
Page 50
GB 50 L01.1E Alignments 8.3.1 Options 7\SHQXPEHU 2% 2% 2% 2% 2% 2% 2% 37 37 37 37 S A M 3: 3: 37 37 O P 1 X X X 37 O P 2 X X X 37 37...
Page 52
GB 52 L01.1E Alignments AP30: AVL 0 : Ultra Bass is disabled or not applicable, 0 : AVL is disabled or not applicable, 1 : Ultra Bass is enabled, 1 : AVL is enabled, Default setting : 0. Default setting : 0.
Page 53
Alignments L01.1E GB 53 OP63: VCHIP OP75: Reserved 0 : VCHIP feature is disabled, Default setting : 0. 1 : VCHIP feature is enabled, Default setting : 1. OP77 and 76: TIME_WIN1, TIME_WIN2 00 : The time window is set to 1.2s...
Page 54
GB 54 L01.1E Alignments 8.3.3 White Tone VERT. SLOPE VERT. SHIFT S A M VERT. AMPLITUDE N O R M A L > C O O L > W A R M > N O R M A L R E D V.S-CORRECTION...
Page 55
Alignments L01.1E GB 55 • Lower Corner Parabola (LCP). Align straight vertical In the table below, you will find the GEOMETRY default lines in the lower corners of the screen. values for the different sets. • East West Trapezium (EWT). Align straight vertical lines in the middle of the screen.
Page 56
GB 56 L01.1E Circuit Description 9. Circuit Description Index of this chapter: 1. Introduction The L01 is divided into 2 basic systems, i.e. mono and stereo 2. Audio Signal Processing sound. While the audio processing for the mono sound is 3.
Circuit Description L01.1E GB 57 9.2.2 Mono 9.3.3 Video Source Selection In mono sets, the signal goes via the SAW filter (position The Composite Video Blanking Signal (CVBS) from buffer 1004 in case of QSS demodulation and 1003 in case of...
Page 58
GB 58 L01.1E Circuit Description Also some picture improvement features are implemented in RGB output signals is therefore proportional to the this part: voltage present on this pin. Contrast reduction starts • Black stretch This function corrects the black level of when the voltage on pin 54 is lower than 2.8 V.
Page 59
Circuit Description L01.1E GB 59 Deflection voltage across this measuring resistor is proportional to the output current, which is available at pins 4 and 7 where they drive the vertical deflection coil (connector 0222) in phase 9.5.1 Horizontal Drive opposition.
GB 60 L01.1E Circuit Description A line, written at the upper- or lower side of the screen, will be larger at the screen centre when a fixed deflection current is used. Therefore, the amplitude of the deflection current SUPPLY START-UP...
Page 61
Circuit Description L01.1E GB 61 Degaussing Control Circuit B1/B2 n⋅V Main Supply Focus Mains AC Input Main Power Panel VideoSupply Supply Main Aux Filament Tilt& Rotation GATE Degaussing Circuit VlotAux +13V 3V3 Reg. Correction Horizontal GATE Vaux Deflection +3.9V +3.3V...
Page 62
GB 62 L01.1E Circuit Description The moment that the voltage on pin 1 drops below the ‘under voltage lock out‘ level (UVLO = ± 9 V), the IC will stop switching and will enter a safe restart from the rectified mains voltage.
Page 63
Circuit Description L01.1E GB 63 • When the set is in protection mode. In Standby, the power supply works in ‘burst mode’. Active/ Burst mode can be used to reduce the power consumption inactive below 1 W at stand-by. During this mode, the controller is...
Page 64
GB 64 L01.1E Circuit Description Over Power Protection 9.7.1 Introduction During the primary stroke, the rectified AC input voltage is measured by sensing the current drawn from pin 4 (DEM). The microprocessor part of the UOC has the complete This current is dependent on the voltage on pin 9 of control and teletext on board.
Page 65
Circuit Description L01.1E GB 65 Abbreviation list information if a Y/C or CVBS source is present (signal is high). The presence of an external Y/C source makes this line ‘high’ while a CVBS source makes the line ‘low’. 2 Carrier (or Channel) Stereo –...
Page 66
GB 66 L01.1E Circuit Description Horizontal Acquisition: horizontal Service Alignment Mode sync pulse coming out of the HIP Second Audio Program Horizontal Flyback Pulse: horizontal Sandcastle: pulse derived from sync sync pulse from large signal signals deflection Short Circuit Headphone...