Service Modes, Error Codes And Faultfinding; Test Points; How To Enter Sdm - Philips L01.1E Service Manual

5. Service Modes, Error Codes and Fault Finding
Index of this chapter:

1. Test points.

2. Service Modes.
3. Problems and Solving Tips (related to CSM).
4. ComPair.
5. Error Codes.
6. The Blinking LED Procedure.
7. Protections.
8. Repair Tips.
5.1 Test Points
The chassis is equipped with test points printed on the circuit
board assemblies. These test points refer to the functional
blocks:
TEST POINT OVERVIEW L01
Test point Circuit
A1-A2-A3-..... Audio processing
C1-C2-C3-.....
Control
F1-F2-F3-.....
Frame drive
I1-I2-I3-..... Tuner & IF
L1-L2-L3-.... Line drive
P1-P2-P3-..... Power supply
S1-S2-S3-..... Synchronisation
V1-V2-V3-.....
Video processing
Figure 5-1
The numbering is in a logical sequence for diagnostics.
Always start diagnosing within a functional block in the
sequence of the relevant test points for that block.
Perform measurements under the following conditions:
• Service Default Mode.
• Video: colour bar signal.
• Audio: 3 kHz left, 1 kHz right.
5.2 Service Modes
Service Default Mode (SDM) and Service Alignment Mode
(SAM) offer several features for the service technician, while
the Customer Service Menu (CSM) is used for
communication between dealer and customer.
There is also the option of using ComPair, a hardware
interface between a computer (see requirements) and the TV
chassis. It offers the ability of structured trouble shooting,
error code reading and software version readout for all L01
chassis.
Minimum requirements: a 486 processor, Windows 3.1 and a
CD-ROM drive. A Pentium Processor and Windows 95/98
are also acceptable (see also paragraph 5.4).
SW SW name
cluster
2EU0 L01ET0 x.y TDA9555
2EU9 L01ET9 x.y TDA9555
3EU1 L01EF1 x.y TDA9565
3EU2 L01EF2 x.y TDA9563
A
bbreviations: E= Europe, F= Full TXT, M= mono, T= 1 page TXT
Figure 5-2
Service Modes, Error Codes and Fault Finding
Diagram
A8, A9 / A11
A7
A3
A4
A2
A1
A6
A5, B1
CL 16532008_044.eps
210501
UOC-type Diversity Remark
West Europe, All Service
1 page TXT Modes
East Europe, All Service
1 page TXT Modes
West Europe, All Service
10 page TXT Modes
East Europe, All Service
10 page TXT Modes
CL 16532008_045.eps
5.2.1 Service Default Mode (SDM)
Purpose
• To create a predefined setting to get the same
measurement results as given in this manual.
• To override SW protections.
• To start the blinking LED procedure.
Specifications
• Tuning frequency:
– 475.25 MHz for PAL/SECAM (Europe and AP-PAL).
– 61.25 MHz (channel 3) for NTSC-sets (NAFTA,
LATAM and AP-NTSC).
• Colour system:
– PAL-M for LATAM BI/TRI/FOUR-NORMA.
– SECAM L for France.
– NTSC for NAFTA and AP-NTSC.
– PAL-BG for Europe and AP-PAL.
• All picture settings at 50 % (brightness, colour contrast,
hue).
• Bass, treble and balance at 50 %; volume at 25 %.
• All service-unfriendly modes (if present) are disabled,
like:
– (sleep) timer,
– child/parental lock,
– blue mute,
– hotel/hospitality mode
– auto switch-off (when no 'IDENT' video signal is
received for 15 minutes),
– skip / blank of non-favorite presets / channels,
– auto store of personal presets,
– auto user menu time-out.

How to enter SDM

Use one of the following methods:
• Use a standard customer RC-transmitter and key in the
code '062596' directly followed by the MENU button or
• Short wires 9631 and 9641 on the mono carrier (see Fig.
8-1) and apply Mains power. Then press the power
button (remove the short after start-up).
Caution: Entering SDM by shorten wires 9631 and 9641
will override the +8V-protection. Do this only for a short
period. When doing this, the service-technician must
know exactly what he is doing, as it could lead to
damaging the set.
• Or via ComPair.
210501
L01.1E 5. GB 13