Panasonic VQT9958 Operating Instructions Manual page 48

CONTENTS
Setup menus
USER menu
<AUDIO>
No./Item
721 This selects the monitor output.
MONI CH SEL 0000 MANU :
The output signal is as selected in MONITOR
SELECT buttons.
0001 AUTO :
PCM AUDIO output is selected within the
–0.43 (–0.5)a to +1a speed range; CUE is
automatically selected for all other tape
speeds.
<Note>
The value for the DV/DVCAM tape is shown in
parenthesis (
0002 PCM :
The PCM AUDIO signal is output over the
–10a to +10a range.
<Note>
This setup menu's setting takes effect when CH1,
CH2, CH3 or CH4 has been selected by the L
and R MONITOR SELECT buttons on the front
panel. (If CUE has been selected, the cue signal
will be output at all the speeds regardless of the
setup menu's setting.)
722 This selects the input signal to be recorded
on the audio CH1 track.
REC CH1
0000 CH1 : Audio input CH1 signal.
0001 CH2 : Audio input CH2 signal.
0002 CH1+2 : Mixed audio input CH1 and CH2
723 This selects the input signal to be recorded
on the audio CH2 track.
REC CH2
0000 CH1 : Audio input CH1 signal.
0001 CH2 : Audio input CH2 signal.
0002 CH1+2 : Mixed audio input CH1 and CH2
724 This selects the input signal to be recorded
on the audio CH3 track.
REC CH3
0000 CH3 : Audio input CH3 signal
0001 CH4 : Audio input CH4 signal
0002 CH3+4 : Mixed audio input CH3 and CH4
725 This selects the input signal to be recorded
on the audio CH4 track.
REC CH4
0000 CH3 : Audio input CH3 signal
0001 CH4 : Audio input CH4 signal
0002 CH3+4 : Mixed audio input CH3 and CH4
The underlined items indicates the initial setting.
Description
).
signal.
signal.
signal
signal
48 (E)
No./Item
726 This selects the input signal recorded in CUE.
REC CUE 0001 CH1 : Audio CH1 input
0002 CH2 : Audio CH2 input
0003 CH1+2 : Audio CH1 and CH2 MIX signal
0004 CH3 : Audio CH3 input
0005 CH4 : Audio CH4 input
0006 CH3+4 : Audio CH3 and CH4 MIX signal
CH1 ~ 4 : Audio CH1, CH2, CH3 and CH4
0007
727 This selects the processing method for the
audio edit points (IN point, OUT point) during
PB FADE playback.
0000 AUTO : According to the status during
0001 CUT : Forced CUT
0002 FADE : Forced FADE
728 This selects whether to superimpose the
audio data onto the serial output.
EMBEDDED
AUD 0000 OFF : Data is not superimposed.
0001 ON : Data is superimposed.
731 This selects whether or not the cue signal is
to be output to the main line output in the
CUE OUT SEL search mode.
0000 OFF : CUE is not output.
0001 ON : CUE is output.
<Notes>
OThis function works only when a setting
other than MANU has been selected by
setup menu No. 721 (MONI CH SEL).
OThe main signal system output channels
used for the CUE output differ depending on
the setting selected by setup menu No. 735
(MON AUTO SEL).
When L/R is selected:
CUE is output to CH1 to CH4.
When L is selected:
CUE is output to CH1 and CH3.
When R is selected:
CUE is output to CH2 and CH4.
OWhen PCM has been selected as the setup
menu No. 721 (MONI CH SEL) setting, PCM
is output.
733 This selects the timing for the output picture
and CUE output when CUE has been selected
CUE OUT for monitor output.
0000 NORMAL : The timing is aligned with the
0001 DIRECT : Whatever has been recorded on
<Note>
When DIRECT has been selected, the timing of
the output picture and that of the cue output are
not aligned properly.
Description
mixed signals
recording.
output picture.
the tape is output with no delay.