Hans Grohe Ecostat 1001 SL Care 13284000 Installation Instructions Manual
Hide thumbs
Also See for Ecostat 1001 SL Care 13284000:
- Instructions for use/assembly instructions (40 pages) ,
- Instructions for use/assembly instructions (68 pages)
Related Manuals for Hans Grohe Ecostat 1001 SL Care 13284000
Summary of Contents for Hans Grohe Ecostat 1001 SL Care 13284000
- Page 1 Installation Instructions Ecostat 1001 SL Care Ecostat 1001 SL Care 13284000 13282000...
-
Page 2: Table Of Contents
Safety and Important Information Pack Contents Dimensions Technical Data Supply Conditions TMV2 Supply Conditions TMV3 Installation Requirements The Ecostat 1001 SL Care 13284000 meets Installation the requirements of the TMV2 Scheme. Thermostat Commissioning and in-service tests Commissioning In-service tests Frequency of in-service tests... -
Page 3: Safety And Important Information
Safety and Important Information Hansgrohe products are safe provided they are installed, used and maintained in accordance with these instructions and recornrnendations. Please read these instructions thoroughly and retain for future use. The plumbing installation of this shower must comply with the requirements of UK Water Regulations/Bylaws (Scotland), Building Regulations or any other regulations specified by the local Water Authority and supplier. -
Page 4: Pack Contents
Dimensions Pack Contents Please check that you have been supplied with the following: Ecostat 1001 SL Care 13284000 Ecostat 1001 SL Care 13284000 1 Ecostat 1001 SL 3 Escutcheons 2 Mesh washers 4 S-unions Ecostat 1001 SL Care 13282000 Ecostat 1001 SL Care 13282000... -
Page 5: Technical Data
Technical Data Ecostat 1001 SL Care Mixed water temperature This thermostatic valve will suit supplies of: Application Mixed water temperature HIGH PRESSURE (HP-S) (at point of discharge) Bidet 38°C max. Operating pressure: max. 10 bar Shower 41°C max. Recommended operating pressure: 0.2 - 5 bar Washbasin 41°C max. -
Page 6: Installation Requirements
Installation Requirements This thermostatic mixer valve must be installed in compliance with current Water Regulations. If you have any doubts about the Water Regulation requirements contact your local water services provider or use the services of a professional plumber. This mixer valve is suitable for use with the following water supply systems: Gravity Fed Hot and Cold (pressure balanced) 0.1 - 1.0 bar Gas Combination Boiler (multi-point) 1.0 - 10 bar*... - Page 7 Unvented System (pressure balanced) Pumped System...
-
Page 8: Installation
Installation Shower Thermostat PTFE tape 150 mm COLD 32 - 41 Seal Shower Thermostat Bath/Shower Thermostat 1. The hot and cold water outlets should be 150mm As the shower thermostat above (positioned over apart (plus or minus 12mm). Hot on the left and a bath). -
Page 9: Commissioning And In-Service Tests Commissioning
Commissioning and in-service tests Commissioning record the equipment, thermometer etc. used for the measurements Purpose Table A: Guide to maximum stabilised Since the installed supply conditions are likely to temperatures recorded during site be different from those applied in the laboratory tests tests it is appropriate, at commissioning, to carry Application... -
Page 10: In-Service Tests
In-service tests Frequency of in-service tests TMV3* Purpose General The purpose of in-service tests is to regularly monitor and record the performance of the thermostatic In the absence of any other instruction or guidance on mixing valve. Deterioration in performance can the means of determining the appropriate frequency indicate the need for service work on the valve and of in-service testing, the following procedure may... -
Page 11: Thermostatic Adjustement
Thermostatic Adjustment Temperature Limitation SW 3 mm The temperature is limited by the safety stop to 40°C. If a higher temperature is required, it is possible to over ride the safety stop by depressing the safety button. NB. It is recommended that for private domestic use the maximum mixed water temperature be set at the following factory set values: Shower Mixer 43°C... -
Page 12: Operating Your Shower
Operating your Shower Ecostat 1001 SL Care Flow ON/OFF Control Turn the flow control handle (fig.1a) anti-clockwise to turn the water on and to increase the flow. Turn it clockwise to decrease the flow and turn off. Temperature Control Turn the temperature control handle (fig. 1b) anti- clockwise to increase the water temperature and clockwise to decrease the water temperature. -
Page 13: Cleaning
Cleaning Cleaning materials for Mixers and Showers Acids are necessary ingredients of cleaning materials for removing lime. However please pay particular attention to the following points when cleaning mixers and showers: Only use cleaning material specifically intended for this type of cleaning - such as Hansgrohe’s Decalcifying Agent, available through the specialist sanitary trade. -
Page 14: Spare Parts
Spare Parts Bath/Shower Thermostat NV15/ DN15 Thermostatic element 94282000 Shut off and diverter unit 96509000 Handle for shut off and diverter unit and temperature control 98664000 Check valve NV15/ DN15 96737000 S-unions 94140000 Escutcheon 96467000 Filter packing 96922000 Noise reduction 96429000 Aerator cpl. - Page 15 Spare Parts Shower Thermostat NV15/ DN15 Thermostatic element 94282000 Shut off unit 94149000 Handle for shut off unit and temperature control 98664000 Check valve NV15/ DN15 96737000 S-unions 94140000 Escutcheon 96467000 Filter packing 96922000 Noise reduction 96429000...
-
Page 16: Trouble Shooting
Trouble Shooting Fault Cause Remedy Insuffient water flow Supply pressure inadequate Check mains pressure Shower filter seal dirty Clean filter seal between shower and hose Thermostat cartridge filters dirty Remove cartridge & clean the filters on the barrel ‚Crossflow‘, hot water is forced check valves dirty or Clean check valves - into cold water pipe, or vice...