Stihl BR 200 Instruction Manual
  1. Manuals
  2. Brands
  3. Stihl Manuals
  4. Blower
  5. BR 200
  6. Instruction manual

Stihl BR 200 Instruction Manual

Hide thumbs Also See for BR 200:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
{
STIHL BR 200
Instruction Manual

Advertisement

Table of Contents
loading

Related Manuals for Stihl BR 200

Summary of Contents for Stihl BR 200

  • Page 1 STIHL BR 200 Instruction Manual...

  • Page 3: Table Of Contents

    English Contents Dear Customer, Guide to Using this Manual Safety Precautions and Working Thank you for choosing a quality engineered STIHL product. Techniques Assembling the Unit It has been built using modern Adjusting the Throttle Cable production techniques and comprehensive quality assurance.

  • Page 4: Guide To Using This Manual

    English Engineering improvements Guide to Using this Manual Safety Precautions and Working Techniques STIHL's philosophy is to continually Special safety precau - improve all of its products. For this Pictograms reason we may modify the design, tions must be observed...
  • Page 5 (e.g. with a hair vision, dexterity or judgment. explicitly approved for this power tool by net, cap, hard hat, etc.). STIHL or are technically identical. If you Wear sturdy shoes with non-slip soles. Intended Use have any questions in this respect, consult a servicing dealer.
  • Page 6 English Fueling Before Starting blower housing is damaged, consult your dealer – STIHL recommends you contact a STIHL servicing dealer. Check that your power tool is properly Gasoline is an extremely To reduce the risk of accidents, do not assembled and in good condition – refer flammable fuel.
  • Page 7 – do not run the engine To reduce the risk of accidents, take a unnecessarily, accelerate the engine break in good time to avoid tiredness or only when working. exhaustion. BR 200...
  • Page 8 Observe local advice. Use only a spark plug of the type rest periods. approved by STIHL and make sure it is Operate blowers at the lowest Maintenance and Repairs – in good condition – see "Specifications".

  • Page 9: Assembling The Unit

    Connect the blower tube (1) and nozzle (2). Push the pleated hose (2) over the slip ring (3) as far as stop. Line up the hose clamp (1) and slip ring (3) – as shown. Connect the blower tube (1) to tube (3). BR 200...

  • Page 10: Adjusting The Throttle Cable

    Push the blower tube (4) into the against your back. stub of pleated hose (2) as far as the stop. Move the control handle (6) along the tube to the most comfortable position. Tighten down the screw on the control handle (6). BR 200...

  • Page 11: Fuel

    Use only high-quality two-stroke engine STIHL MotoMix uses STIHL HP Ultra location protected from light and the sun. oil – preferably STIHL HP, HP Super or two-stroke engine oil for an extra long Fuel mix ages – only mix sufficient fuel HP Ultra, which are specially formulated engine life.

  • Page 12: Fueling

    Fueling fluid properly in accordance with local regulations and environmental Take care not to spill fuel while fueling requirements. and do not overfill the tank. STIHL recommends you use the STIHL filler nozzle (special accessory). Preparations Closing screw-type tank cap Place the cap in the opening.

  • Page 13: Information Before You Start

    (1) is not locked in this position. It springs back to the run position F. The ignition is switched on again. Press the manual fuel pump bulb at least five times – even if the bulb is filled with fuel. BR 200...
  • Page 14 Do not pull out the starter rope to full length – it might otherwise break. Do not let the starter grip snap back. Guide it slowly back into the housing so that the starter rope can rewind properly. Continue cranking until the engine runs. BR 200...

  • Page 15: Operating Instructions

    – see "Storing the Machine". Choke knob automatically returns to the run position F when the throttle trigger is operated. At very low outside temperatures Open throttle slightly – warm up the engine for a short period. BR 200...

  • Page 16: Cleaning The Air Filter

    Pull off the adapter (3) and remove the filter (4). Fit a new filter element. As a temporary measure you can knock it out on the palm of your hand or blow it out with compressed air. Do not wash. Replace any damaged parts. BR 200...

  • Page 17: Catalytic Converter

    (depending on model) must be run on a Turn the low speed screw (L) 50 : 1 mixture of unleaded gasoline and counterclockwise, no further than STIHL two-stroke engine oil or stop, until the engine runs and equivalent two-stroke engine oil – see accelerates smoothly.

  • Page 18: Spark Plug

    Fit a new spark plug after about 100 operating hours – or sooner if the electrodes are badly eroded. Install only suppressed spark plugs of the type approved by STIHL – see "Specifications". Clean dirty spark plug. Check electrode gap (A) and Removing the Spark Plug readjust if necessary –...

  • Page 19: Engine Running Behavior

    (carbonization) by your environmental requirements. servicing dealer. Run the engine until the carburetor STIHL recommends that you have is dry – this helps prevent the servicing and repair work carried out carburetor diaphragms sticking exclusively by an authorized STIHL together.

  • Page 20: Maintenance And Care

    Carburetor Readjust idle Readjust electrode gap Spark plug Replace after every 100 operating hours Visual inspection Cooling inlet Clean All accessible screws and nuts (not adjust - Retighten ing screws) Check Anti-vibration elements Have replaced by servicing dealer BR 200...
  • Page 21 (very dusty work area, etc.), shorten the specified intervals accordingly. Check Blower air intake screen Clean Throttle cable Adjust Safety labels Replace STIHL recommends an authorized STIHL servicing dealer. BR 200...

  • Page 22: Minimize Wear And Avoid Damage

    English servicing dealer. STIHL dealers are Minimize Wear and Avoid regularly given the opportunity to attend Damage training courses and are supplied with the necessary technical information. Observing the instructions in this manual helps reduce the risk of unnecessary If these maintenance operations are not wear and damage to the power tool.

  • Page 23: Main Parts

    12 Muffler (with spark arresting screen) 13 Starter grip 14 Spark plug boot 15 Manual fuel pump 16 Carburetor adjusting screws 17 Choke knob 18 Filter cover 19 Tank cap 20 Fuel tank 21 Spacer Serial number Not in all versions, country-specific BR 200...

  • Page 24: Specifications

    Registration, Evaluation, Engine Authorisation and Restriction of Noise and Vibration Data Chemical substances. STIHL single cylinder two-stroke engine For information on compliance with the Noise and vibration data are measured Displacement: 27.2 cc REACH regulation (EC) No. 1907/2006 at idling and maximum rated speed in a see www.stihl.com/reach.

  • Page 25: Maintenance And Repairs

    2006/42/EC, 2004/108/EC (up to replacement parts which have been accessories and packaging to an 19.04.2016), 2014/30/EU (from approved by STIHL for this power tool or approved disposal site for environment- 20.04.2016) and 2000/14/EC and has are technically identical. Only use high- friendly recycling.
  • Page 26 English Done at Waiblingen, 09.11.2015 ANDREAS STIHL AG & Co. KG Thomas Elsner Director Product Management and Services BR 200...
  • Page 28 0458-455-0121-B englisch www.stihl.com *04584550121B* 0458-455-0121-B...

Table of Contents