Yamaha HTR-N5060 Owner's Manual page 74

SET MENU
Speaker distance
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
C)SP DISTANCE
. UNIT;;;;;;meters
FRONT L;;;;3.00m
FRONT R;;;;3.00m
CENTER;;;;;3.00m
[ ]/[ ]:Up/Down
[<]/[>]:Adjust
Unit UNIT
Choices: meters (m), feet (ft)
Initial setting:
[Canada model]: feet (ft)
[Other models]: meters (m)
• Select "meters" to adjust speaker distances in meters.
• Select "feet" to adjust speaker distances in feet.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
• Select "FRONT L" to adjust the distance of the front
left speaker.
Initial setting: 3.00 m (10.0 ft)
• Select "FRONT R" to adjust the distance of the front
right speaker.
Initial setting: 3.00 m (10.0 ft)
• Select "CENTER" to adjust the distance of the center
speaker.
Initial setting: 3.00 m (10.0 ft)
• Select "SUR. L" to adjust the distance of the surround
left speaker.
Initial setting: 3.00 m (10.0 ft)
• Select "SUR. R" to adjust the distance of the surround
right speaker.
Initial setting: 3.00 m (10.0 ft)
• Select "SUR. B" to adjust the distance of the surround
back speaker.
Initial setting: 2.10 m (7.0 ft)
• Select "SWFR" to adjust the distance of the subwoofer.
Initial setting: 3.00 m (10.0 ft)
Note
"CENTER", "SUR.L", "SUR.R", "SUR.B" and "SWFR" cannot
be adjusted if "CENTER SP" (see page 70), "SUR. L/R SP" (see
page 70), "SUR. B SP" (see page 70) and "LFE/BASS OUT" (see
page 70) are set to "NONE" respectively.
72
En
C)SP DISTANCE Center graphic equalizer
Use this feature to adjust the built-in 5-frequency band
(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments while listening to the currently
selected source component or a test tone.
Control range: –6 to +6 dB
Control step: 0.5 dB
Initial setting: 0 dB
D)CENTER GEQ
. TEST
100Hz ;;;;;;
300Hz ;;;;;;
1kHz ;;;;;;
3kHz ;;;;;;
10kHz ;;;;;;
[ ]/[ ]:Up/Down
[<]/[>]:Adjust
Test tone TEST
Choices: OFF, ON
• Select "OFF" to stop test tones and output the currently
selected source component.
• Select "ON" to output test tones from the front left and
center speakers, and adjust the tonal quality of the
center speaker.
y
Press u / d to select a frequency band and j / i to adjust the
selected frequency band.
Low-frequency effect level
Use this feature to adjust the output level of the LFE (low-
frequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Control range: –20 to 0 dB
Control step: 1 dB
E)LFE LEVEL
. SPEAKER;;;;;;0dB
HEADPHONE;;;;0dB
[ ]/[ ]:Up/Down
[<]/[>]:Adjust
Speaker SPEAKER
Adjusts the speaker LFE level.
Headphone HEADPHONE
Adjusts the headphone LFE level.
Note
Depending on the settings of "LFE/BASS OUT" (see page 70),
some signals may not be output at the SUBWOOFER OUTPUT
jack.
D)CENTER GEQ
>OFF ON
-______+
0dB
0dB
0dB
0dB
0dB
E)LFE LEVEL