Table of Contents
Advertisement
Time programming function
This function may be used in two different ways:
to automatically switch off a hotplate.
■
as a timer.
■
Turn off a hotplate automatically
Enter the cooking time for the desired hotplate. The hotplate
turns off automatically once the time has elapsed.
Programming
Select the desired power level.
1.
Press the
0
symbol. The
2.
up.
‹‹
lights up in the time program function display. To
select another hotplate, press the
until the
indicator for the desired hotplate lights up.
x
Select the required cooking time in the programming panel.
3.
The possible previous setting is, from left to right 1, 2, 3, etc.,
up to 10 minutes. Within the next 10 seconds, continue past
the options in the programming panel until reaching the
desired time.
After a few seconds the cooking time begins to count down.
Automatic programming
If the previous setting from 1 to 5 is pressed in the
programming panel, the cooking time is reduced by one
minute, if it is held down the time is automatically reduced to
one minute.
If the previous setting from 6 to 10 is pressed in the
programming panel , the cooking time is increased by one
minute, if it is held down the time is automatically increased to
99 minutes.
Once the time has elapsed
The hotplate switches off. An audible signal sounds and
appears in the time program function display for 10 seconds.
The
indicator lights up. Pressing the
x
indicators and stops the signal.
Automatic time limitation
If the hotplate remains in use for a long time and no changes
are made in the settings, the automatic time limitation function
is triggered.
The hotplate stops heating. On the hotplate display,
flash alternately.
The indicator goes out when any symbol is pressed. The
hotplate can now be reset.
x
indicator of the hotplate lights
symbol several times
0
symbol turns off the
0
"
Changing or cancelling the time
Press the
0
lights up. Change the cooking time in the programming panel,
or set to
‹‹
Automatically switch off a hotplate with the deep-frying
function
When cooking using the deep-frying function, the programmed
cooking time begins to count down once the selected hotplate
reaches the desired temperature.
Notes
If a cooking time has been programmed in several zones, it
■
can be set to display all time values. To do this, press the
symbol several times until the
hotplate lights up.
Cooking times of up to 99 minutes can be programmed.
■
Automatic timer
With this function you may select a cooking time for all
hotplates. Once a hotplate is switched on, the selected time will
begin to count down. The hotplate will automatically switch off
when the cooking time has elapsed.
Instructions on activating the timer are found in the chapter
entitled "Basic settings".
Note: The cooking time of a zone may be cancelled or
changed:
Press the
0
indicator lights up. Change the cooking time in the
programming panel, or set to
The timer
The timer can be set for periods of up to 99 minutes. It is
independent of the other settings. This function does not
automatically switch off a hotplate.
Programming
Press the
0
1.
up.
lights up in the time program function display.
‹‹
Select the desired time in the programming panel.
2.
The timer starts to count down after a few seconds.
Once the time has elapsed
A warning beep sounds. In the time program function display
is shown, and the
‹‹
‹‹
the indicators turn off.
Pressing the
beep.
Changing or cancelling the time
Press the
0
up. Change the cooking time in the programming panel, or set
to
‹‹
.
When the automatic time function is used, it is governed by the
selected power level (from 1 to 10 hours).
and
‰
symbol several times until the desired
.
x
indicator for the required
symbol several times until the required
‹‹
.
symbol several times until the
indicator comes on. After 10 seconds
W
symbol turns off the indicators and stops the
0
symbol several times until the
indicator
x
0
x
indicator lights
W
indicator lights
W
13
Advertisement
Table of Contents
