1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Network Hardware
  5. UD.6L0202B1194A01
  6. Quick operation manual

HIKVISION UD.6L0202B1194A01 Quick Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Network Video Recorder
Quick Operation Guide
UD.6L0202B1194A01

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION UD.6L0202B1194A01

Summary of Contents for HIKVISION UD.6L0202B1194A01

  • Page 1 Network Video Recorder Quick Operation Guide UD.6L0202B1194A01...

  • Page 2: Table Of Contents

    Quick Operation Guide of Network Video Recorder TABLE OF CONTENTS NVR Pre-Installation ............................2 NVR Installation .............................. 2 Hard Disk Installation ............................. 3 Front Panel ............................... 7 Rear Panel ..............................14 Peripheral Connections ..........................17 Wiring of Alarm Input ..........................17 Wiring of Alarm Output ...........................

  • Page 3: Nvr Pre-Installation

    Quick Operation Guide of Network Video Recorder Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable to the models listed in the following table. Series Model Type 9600NI-ST...

  • Page 4: Hard Disk Installation

    Quick Operation Guide of Network Video Recorder 6. Ensure the NVR is grounded. 7. Environmental temperature should be within the range of -10 º C ~ 55 º C, 14º F ~ 131º F. 8. Environmental humidity should be within the range of 10% ~ 90%. Hard Disk Installation Before you start: Disconnect the power from the NVR before installing a hard disk drive (HDD).
  • Page 5 Quick Operation Guide of Network Video Recorder 5. Repeat the above steps to install other hard disks onto the NVR. After having finished the installation of all hard disks, close the front panel and lock it with the key again. Steps (for DS-8600NI-ST): 1.
  • Page 6 Quick Operation Guide of Network Video Recorder 4. Connect the power cable to the HDD. 5. Re-install the cover of the NVR and fasten screws. Steps (for DS-7600NI-ST/SP and DS-7700NI-ST/SP): Remove the cover from the NVR by unfastening the screws on the rear and side panel. Connect one end of the data cable to the motherboard of NVR and the other end to the HDD.
  • Page 7 Quick Operation Guide of Network Video Recorder 4. Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.

  • Page 8: Front Panel

    Quick Operation Guide of Network Video Recorder Front Panel DS-9600NI-ST/RT DS-9600NI-XT DS-8600NI-ST Name Function Description ALARM Turns red when a sensor alarm is detected. Ready LED is normally blue, indicating that the device is READY functioning properly. Turns blue when device is controlled by an IR remote. STATUS Turns red when controlled by a keyboard and purple when IR Status...
  • Page 9 Quick Operation Guide of Network Video Recorder Name Function Description Guard LED turns blue when the device is in armed status; at this time, an alarm is enabled when an event is detected. GUARD The LED turns off when the device is unarmed. The arm/disarm status can be changed by pressing and holding on the ESC button for more than 3 seconds in live view mode.
  • Page 10 Quick Operation Guide of Network Video Recorder Name Function Description play. Cycle through tab pages. F2/ AUX In synchronous playback mode, it is used to switch between channels. Press the button will help you return to the Main menu (after successful login).
  • Page 11 Quick Operation Guide of Network Video Recorder DS-7700NI-ST/SP Name Function Description POWER Turns green when NVR is powered up. READY The LED is green when the device is running normally. The light is green when the IR remote control is enabled; The light is red when the function of the composite keys (SHIFT) Status STATUS...
  • Page 12 Quick Operation Guide of Network Video Recorder Name Function Description In PTZ Control mode, it will turn on/off PTZ light and when the image is zoomed in, the key is used to zoom out. Enter numeral “3”; Enter letters “DEF”; 3/DEF/F2 The F2 button is used to change the tab pages.
  • Page 13 Quick Operation Guide of Network Video Recorder DS-7600NI-ST/SP: Name Function Description USB Interface Connects USB mouse or USE flash memory devices. POWER Turns green when NVR is powered up. READY The LED is green when the device is running normally. The light is green when the IR remote control is enabled;...
  • Page 14 Quick Operation Guide of Network Video Recorder Name Function Description Delete characters before cursor; Check the checkbox and select the ON/OFF switch; Start/stop record clipping in playback. Enter numeral “6”; Enter letters “MNO”; 6/MNO/PLAY Playback, for direct access to playback interface. Enter numeral “7”;...

  • Page 15: Rear Panel

    Quick Operation Guide of Network Video Recorder Rear Panel DS-9600NI-ST/RT and DS-8600NI-ST DS-9600NI-XT DS-7700NI-ST DS-7700NI-SP Item Description VIDEO OUT BNC connector for video output. CVBS AUDIO OUT BNC connector for audio output. This connector is synchronized with CVBS video output. VGA AUDIO OUT BNC connector for audio output.
  • Page 16 Quick Operation Guide of Network Video Recorder Item Description HDMI HDMI video output connector. eSATA (Optional) Connects external SATA HDD, CD/DVD-RM. 2 eSATA interfaces for DS-9600NI-XT. LAN Interface 1 network interface provided for DS-7700NI-ST/SP and 2 network interfaces for DS-9600NI-ST/RT/XT and DS-8600NI-ST. Termination Switch RS-485 termination switch.
  • Page 17 Quick Operation Guide of Network Video Recorder Item Description ALARM IN Connector for alarm input. ALARM OUT Connector for alarm output. Power Supply 12VDC power supply. Power Switch Switch for turning on/off the device. Ground Ground (needs to be connected when NVR starts up). Network Interfaces with PoE function (supported Network interfaces for the cameras and to provide power over Ethernet.

  • Page 18: Peripheral Connections

    Quick Operation Guide of Network Video Recorder Peripheral Connections Wiring of Alarm Input The alarm input is an open/closed relay. To connect the alarm input to the device, use the following diagram. Note: if the alarm input is not an open/close relay, please connect an external relay between the alarm input and the device.

  • Page 19: Controller Connection

    Quick Operation Guide of Network Video Recorder Controller Connection To connect a controller to the NVR: Disconnect pluggable block from the KB terminal block. Unfasten stop screws from the KB D+, D- pluggable block, insert signal cables into slots and fasten stop screws.

  • Page 20: Specifications

    Quick Operation Guide of Network Video Recorder Specifications Specifications of DS-9600NI-ST DS-9608NI DS-9616NI- DS-9632NI- DS-9664NI- Model IP video input 8-ch 16-ch 32-ch 64-ch Video/Audio input 1-ch, BNC (2.0 Vp-p, 1kΩ) Two-way audio Recording 5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF resolution /QCIF Main stream: 25 fps (P) / 30 fps (N)

  • Page 21: Specifications Of Ds-9600Ni-Rt

    Quick Operation Guide of Network Video Recorder Specifications of DS-9600NI-RT DS-9608NI- DS-9616NI- DS-9632NI- DS-9664NI- Model IP video input 8-ch 16-ch 32-ch 64-ch Video/Audio input 1-ch, BNC (2.0 Vp-p, 1kΩ) Two-way audio Recording 5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF resolution /QCIF Main stream: 25 fps (P) / 30 fps (N)

  • Page 22: Specification Of Ds-9600Ni-Xt

    Quick Operation Guide of Network Video Recorder Specification of DS-9600NI-XT Model DS-9616NI-XT DS-9632NI-XT DS-9664NI-XT IP video input 16-ch 32-ch 64-ch Video/Audio input 1-ch, BNC (2.0 Vp-p, 1kΩ) Two-way audio Recording 5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF resolution /QCIF Main stream: 25 fps (P) / 30 fps (N)

  • Page 23: Specifications Of Ds-8600Ni-St

    Quick Operation Guide of Network Video Recorder Specifications of DS-8600NI-ST DS-8608NI DS-8616NI- DS-8632NI DS-8664NI Model IP video input 8-ch 16-ch 32-ch 64-ch Video/Audio input 1-ch, BNC (2.0 Vp-p, 1kΩ) Two-way audio 5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF Recording resolution /QCIF Main stream: 25 fps (P) / 30 fps (N)

  • Page 24: Specification Of Ds-7700Ni-St

    Quick Operation Guide of Network Video Recorder Specification of DS-7700NI-ST DS-7708NI DS-7716NI- DS-7732NI DS-7764NI Model IP video input 8-ch 16-ch 32-ch 64-ch Video/Audio input 1-ch, BNC (2.0 Vp-p, 1kΩ) Two-way audio 5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF Recording resolution /QCIF Main stream: 25 fps (P) / 30 fps (N)

  • Page 25: Specification Of Ds-7700Ni-Sp

    Quick Operation Guide of Network Video Recorder Specification of DS-7700NI-SP Model DS-7708NI-SP DS-7716NI-SP DS-7732NI-SP IP video input 8-ch 16-ch 32-ch Video/Audio input 1-ch, BNC (2.0 Vp-p, 1kΩ) Two-way audio Recording 5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF resolution /QCIF Main stream: 25 fps (P) / 30 fps (N)

  • Page 26: Specifications Of Ds-7600Ni-St

    Quick Operation Guide of Network Video Recorder Specifications of DS-7600NI-ST Model DS-7608NI-ST DS-7616NI-ST DS-7632NI-ST IP video input 8-ch 16-ch 32-ch Video/Audio input 1-ch, BNC (2.0 Vp-p, 1kΩ) (Two-way audio) Audio in Recording 5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF resolution /QCIF Main stream: 25 fps (P) / 30 fps (N)

  • Page 27: Specifications Of Ds-7600Ni-Sp

    Quick Operation Guide of Network Video Recorder Specifications of DS-7600NI-SP Model DS-7608NI-SP DS-7616NI-SP DS-7632NI-SP IP video input 8-ch 16-ch 32-ch Video/Audio input 1-ch, BNC (2.0 Vp-p, 1kΩ) (Two-way audio) Audio in Recording 5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF resolution /QCIF Main stream: 25 fps (P) / 30 fps (N)

  • Page 28: Hdd Storage Calculation Chart

    Quick Operation Guide of Network Video Recorder HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 128K 160K 192K 224K...

  • Page 29: Accessing By Web Browser

    Quick Operation Guide of Network Video Recorder Accessing by Web Browser Logging In You can get access to the device via web browser. Open web browser, input the IP address of the device and then press Enter. The login interface appears. Input the user name and password, and click the Login button.

  • Page 30: Recording

    Quick Operation Guide of Network Video Recorder Note: PTZ function can only be realized if the connected camera supports PTZ control. Video Parameters Configuration: Brightness, contrast, saturation and hue of the image can be modified. Start Live View Steps: In the live view window, select a playing window by clicking the mouse. Double click a camera from the device list to start the live view.
  • Page 31 Quick Operation Guide of Network Video Recorder Choose the day in a week to configure scheduled recording. Click Edit to edit record schedule. Configure All Day or Customize Record:  If you want to configure the all-day recording, please check the All Day checkbox. ...

  • Page 32: Playback

    Quick Operation Guide of Network Video Recorder Playback Interface Introduction Channel List: Displays the list of channels and the playing status of each channel. Playback Window: Displays the image of channel. Play Control Bar: Play control operations are supported. Time Line: Displays the time bar and the records marked with different colors. Playback Status: Displays the playback status, including channel number and playback speed.

  • Page 33: Log

    Quick Operation Guide of Network Video Recorder You can view and export the log files at any time, including operation, alarm, exception and information of device. Before you start The Log function can be realized only when the device is connected with HDD or network disk. Steps: Click Log on the menu bar to enter the Log interface.

  • Page 34: Menu Operation

    Quick Operation Guide of Network Video Recorder Menu Operation Menu Structure The menu structure of the DS-9600/8600/7700/7600NI-ST, DS-7700/7600NI-SP and DS-9600NI-XT (RAID disabled) Series NVR: The menu structure of the DS-9600NI-RT Series NVR: Startup and Shutdown Proper startup and shutdown procedures are crucial to expanding the life of the NVR. To start your NVR:...

  • Page 35: Live View

    Quick Operation Guide of Network Video Recorder 1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an Uninterruptible Power Supply (UPS) be used in conjunction with the device. The Power LED on the front panel should be red, indicating the device gets the power supply.
  • Page 36 Quick Operation Guide of Network Video Recorder Select Add IP Camera in the pop-up menu to enter the IP Camera Management interface. The online cameras with same network segment will be displayed in the camera list. Click the button to add the camera.

  • Page 37: One-Touch Raid Configuration

    Quick Operation Guide of Network Video Recorder You can edit the IP address, protocol, management port, and other information of the IP camera to be added. Click Add to add the camera. (For the encoders with multiple channels only) check the of Channel No.

  • Page 38: Recording

    Quick Operation Guide of Network Video Recorder Click to enter the One-touch Array Configuration interface. Edit the array name in the Array Name text filed and click OK button to start configuring array. Note: If you install 4 HDDs or above for one-touch configuration, a hot spare disk will be set by default. It is recommended to set hot spare disk for automatically rebuilding the array when the array is abnormal.

  • Page 39: All-Day Recording

    Quick Operation Guide of Network Video Recorder All-day Recording Steps: 1. On the live view window, right lick the window and move the cursor to the Start Recording option, and select Continuous Record or Motion Detection Record on your demand. 2.

  • Page 40: Backup

    Quick Operation Guide of Network Video Recorder Front Panel: press PLAY button to play back record files of the channel under single-screen live view. Under multi-screen live view, record files of the selected channel will be played back. Note: pressing numerical buttons will switch playback to related channels during playback process. Playback management.
  • Page 41 Quick Operation Guide of Network Video Recorder Enter Export interface, choose backup device and click Export button to start exporting. Check backup result. Choose the record file in Export interface and click button to check it. 0300001030719...
  • Page 42 Quick Operation Guide of Network Video Recorder...

Table of Contents