Whirlpool AMD 093 User Manual
Whirlpool AMD 093 User Manual

Whirlpool AMD 093 User Manual

Portable air conditioner

Advertisement

SAFETY PRECAUTIONS

• Do not install the appliance if it is connected to
the power supply.
• The Installation and service/repair must be
performed by a qualified technician, in
compliance with the producer's instructions and
following local safety norms. Do not repair or
replace any parts of the appliance unless it is
specifically written in the user instructions.
• The grounding of this appliance is compulsory.
• Make sure that the power supply cord is long
enough to allow the right connection. Do not
use any extension cord for power supply.
• Do not pull the power supply cord to remove it
from the socket.
AIR CONDITIONER PRECAUTIONS
Please strictly follow the below instructions:
• Long and direct exposure to cool air might be
harmful to health. It is advisable to set the
louvers in order to avoid direct cool air and
deflect it within the room.
• Prevent the air flow from reaching the gas
burners and stoves.
SAFEGUARDING THE ENVIRONMENT
• This appliance has been made of recyclable or
re-usable material. Scrapping must be carried
out in compliance with local waste disposal
regulations. Before scrapping it, make sure to
cut off the mains cord so that the appliance
cannot be re-used.
• For more detailed information on handling and
recycling of this product, contact your local
authorities who deal with the separate collection
of rubbish or the shop where you bought the
appliance.
SCRAPPING OF PACKAGING
• The packaging can be 100% recycled as
confirmed by the recycling symbol
various parts of the packaging must not be
dispersed in the environment, but must be
scrapped in line with local authority regulations.
Downloaded from AC-Manual.com Manuals
• Do not twist or press the power supply cord,
and make sure it is not broken.
• Once installation is completed, the electric
components must not be accessible to the users.
• Do not touch the operation buttons when your
hands are wet and don't use the appliance when
you are barefoot.
• Physically or mentally disabled people, children
and people without any experience with the
product are only allowed to use the appliance if
they have had specific training on how to
operate the appliance by a person responsible
for their security and well-being. The appliance
is not intended for use by disabled people and
very young children without supervision.
• Upon malfunctioning first turn the appliance off
by pressing the ON/OFF button on the remote
control, then disconnect it from the mains.
• This product contains Fluorinated Greenhouse
Gases covered by the Kyoto Protocol, the
refrigerant gas being in a hermetically sealed
system. Refrigerant gas: R410a has a Global
Warming Potential (GWP) 1975.
SCRAPPING OF APPLIANCE
• This appliance is marked according to the
European Directive 2002/96/EC, Waste
Electrical and Electronic Equipment (WEEE).
• By ensuring that this product is disposed of
correctly, you will help to prevent potentially
negative consequences for the environment and
for human health.
• The symbol
documents accompanying the product indicates
that this appliance should not be treated as
household waste, but must be given to the
appropriate local gathering place where electric
. The
and electronic appliances are stored and
recycled.
19
on the product or on the

Advertisement

Table of Contents
loading

Summary of Contents for Whirlpool AMD 093

  • Page 1: Safety Precautions

    SAFETY PRECAUTIONS • Do not install the appliance if it is connected to • Do not twist or press the power supply cord, the power supply. and make sure it is not broken. • The Installation and service/repair must be •...
  • Page 2: Starting Your Portable Air Conditioner

    STARTING YOUR PORTABLE AIR CONDITIONER This section explains proper portable air NOTE: When the air conditioner is turned on for conditioner operation. the first time after it is plugged in, it will run in the 6th Sense Mode control. IMPORTANT: When the air conditioner is turned on at all other •...
  • Page 3 STORAGE AND TIPS FOR USING THE RC How to insert the batteries Remove the battery cover in the direction of the arrow. Insert new batteries making sure that the (+) and (-) of battery are matched correctly. Refit the cover by sliding it back into position. Note: •...
  • Page 4: Operating Mode Description

    OPERATING MODE DESCRIPTION Operating modes: NOTE: Auto fan speed cannot be selected in Fan 1. Press and release MODE until you see the Only mode. symbol glow for the desired setting • High-for maximum cooling 2. Choose Cooling, Dry, Fan Only or Heating. •...
  • Page 5 • To change the temperature display between ºC • Press and hold the up or down Adjust button for and ºF, press both the up and down Adjust one and a half seconds to increase or decrease buttons at the same time. the time setting by 10 minutes.
  • Page 6: Using The Remote Control

    USING THE REMOTE CONTROL NOTE: Remote control may vary in appearance. NOTES: • Two AAA batteries (included) power the remote control. Replace batteries after 6 months of use, or when the remote control starts to lose power. • To operate the air conditioner with the remote control, aim the remote control at the signal receptor from no more than 23 ft (7 m) away.
  • Page 7: Function Descriptions

    FUNCTION DESCRIPTIONS 6th Sense mode 2. Each time the "FAN" button is pressed, the fan The air conditioner automatically selects Cooling, speed is changed in sequence: Auto → High → Mid → Low Dry or Heating mode,depending on room temperature and sets the target temperature. ↑...
  • Page 8 where it can transmit the signal to the unit NOTES: properly. Press once to set and press again to • The temperature and airflow direction can be cancel. adjusted during Sleep Mode. If the unit can't receive signal from the remote •...
  • Page 9: Maintenance

    MAINTENANCE Draining the Air Conditioner (in accordance with the indication of Water Full under "Starting your portable air conditioner".) 1. Press ON/OFF to turn off the air conditioner. 2. Unplug air conditioner or disconnect power. 3. Move the appliance gently and stably to a draining location or outside to drain water.
  • Page 10: Troubleshooting

    TROUBLESHOOTING Before calling for service, try the suggestions below to see whether you can solve your problem without outside help.: Trouble Analysis • The power supply cord is unplugged. Plug into a grounded outlet. See "Electrical Requirements." • A household fuse has blown, or a circuit breaker has tripped. Replace the fuse, or reset the circuit breaker.
  • Page 11: Installation Requirements

    INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed • Philips screwdrivers • Saw • Pencil • Scissors • Tape measure A. Foam seal •...
  • Page 12: Installation Instructions

    INSTALLATION INSTRUCTIONS Unpack the Air Conditioner Remove packaging materials • Remove and dispose of/recycle packaging materials. Remove tape and glue residue from surfaces before turning on the air conditioner. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
  • Page 13 Rain Cover-Vertical Installation Rain Cover-Horizontal Installation A. Window exhaust adapter A.Window exhaust adapter B. Rain cover B. Rain cover C.Outlet grille C. Outlet grille D.Window slider kit D.Window slider kit 4. Open the window. 5. Measure the window opening. • If the window opening is too narrow for the window slider kit, remove the inner slider section from the window slider kit.
  • Page 14 6. Place the window slider kit into the window, extending it to fit the width of the window. Be sure the rain cover is on the outside of the window. NOTE: For casement window installation, the window slider kit may be installed vertically with the window slider kit opening at the bottom.
  • Page 15: After Sales Service

    Complete Installation 1. Place window-lock bracket on top of lower window and against upper window sash. 2. Use ¹⁄₈" drill bit to drill a starter hole through the hole in the bracket. 3. Attach window-lock bracket to window sash with ³⁄₄" screw to secure window in place. A.

Table of Contents