How To Program The User Modes; How To Program The Beeper Pitch; How To Display The Serial Number - SamTimer User Manual

16
17
www.SamTimer.com1-888-SamTimer
@ .
sam samtlmer.com
How to Program the User Modes
Follow these easy steps to program a new user mode .
1. Select a mode and set it with the times and options of your
choice (illustrated in Set New Starting Times, p 10).
2. Move to the last option in set mode, which shows COPY to 0
on the display with the zero flashing , and change the zero to
a number from one to twelve. (Number increases with right
play switch and decreases with left.)
3. Long press the center button.
The mode you set will be copied to one of the twelve user
modes . You may repeat this procedure as often as you like .
Example:
1. Turn the clock on with both p' l ay switches pressed . You will
see SCR - 1, SCR - 2, mode identifiers for two Scrabble®
modes .
2. Press the center button twenty-five times . You will see the
mode identifier UP - 1 on the left.
3. Press the left play switch to select this mode. You will see
0:00:00 on the display.
4. Long press the center button to enter set mode . Set the
starting time to 4:00:00, and choose user mode 7 when you
get the option COpy to 0 on the display.
5. Long press the center button to leave set mode, then turn
the clock off.
6. Turn the clock on again with the left play switch pressed .
Press the center button once. You will see the mode identi­
fier UP -
11
on the left for your new user mode 7.
7. Now press the left play switch . The display will show
4:00:00, your new starting time . You are ready to play .
The initial user modes are shown below. User modes 5,6,7, 8
have starting times different from modes 1, 2, and
3.
These set­
tings are suggestions only, and using the procedure above you
should change them to the modes and times you most often use .
How to Program the Beeper Pitch
1. Turn the clock on with both play switches pressed . This will
select all modes of the clock. The display will show SCR ­
1 and SCR - 2.
2. Long press the center button . The display wi" show Pitch,
Sr-Nr. Press the left play switch to select the beeper
pitch. The display will show Pitch 1800.
3. Now long press the center button to set a new pitch. Press
the right play switch to change value of the pitch. Short
press the center red button to change to the next digit.
4. Press the left play switch to test the pitch. Long press
the center red button when you have the pitch you want.
5. Experiment with settings between 29 15 and 2945 to get the
loudest beep. NOTE: the settings are relative and not the
actual cycles per second of the sound produced . You may
select values between 0000 and 2999.
How to Display the Serial Number
1. Turn the clock on with both play switches pressed . This will
select all modes of the clock. The display will show SCR ­
1 and SCR - 2.
2. Long press the center button. The display wil l show Pitch,
Sr-Nr. Press the right play switch to select the serial
number. Your clock's anti-theft serial number' will appear
on the display . This number will help you to identify the
clock if it gets lost.
3. Please record your serial qumber in the space below.
PLEASE DO THIS NOW.
[U
-1-
1 1 1
[-I
[J
[I
BOGGLE
SCR -1 SCR - 2
SCR-3
1,2,3,4
f - ­
SCR -1
SCR-3 SCR -1 SCR - 2 5,6,7,8
_ _ _ _ _ _ 0 _ _ _ _ _
-_
•.
- .- . -. , - ~ -
.
SHO-4 CH - P2 CH - F1
GO - C1 9,10,11,12