Connecting The Power Terminal - Samsung AC052HBMPKH Manual

Connecting the cable
AA

Connecting the Power Terminal

 Connect the cables to the terminal board using the compressed ring terminal.
 Cover a solderless ring terminal and a connector part of the power cable and then connect it.
Nominal Nominal
dimensions dimensions
Standard
for cable for screw
dimension
2 2
[mm (inch )] [mm(inch)]
[mm(inch)]
4(3/8) 9.5(3/8)
4/6
(0.006/
0.009)
8(3/16) 15(9/16)
10(0.01) 8(3/16) 15(9/16)
16(0.02) 8(3/16) 16(10/16)
8(3/16) 12(1/2)
25(0.03)
8(3/16) 16. 5 (10/16)
8(3/16) 16(10/16)
35(0.05)
8(3/16) 22(7/8)
50(0.07) 8(3/16) 22(7/8)
70(0.10) 8(3/16) 24(1)
 Connect the rated cables only.
 Connect using a driver which is able to apply the rated torque to the screws.
 If the terminal is loose, fire may occur caused by arc. If the terminal is connected too firmly, the terminal may be damaged.
M4 12.0~15.0
• When connecting cables, you can connect the cables to the electrical part or connect them through the holes
below depending on the spot.
• Run transmission wiring between the indoor and outdoor units through a conduit to protect against external
forces, and feed the conduit through the wall together with refirgerant piping.
• Remove all burrs at the edge of the knock-out hole and secure the cable to the outdoor knock-out using lining and
bushing with an electrical insulation such as rubber and so on.
• Must keep the cable in a protection tube.
• Keep distances of 50mm or more between power cable and communication cable.
• When the cables are connected through the hole, remove the Plate bottom.
14
B D
Standard
Allowance Allowance
dimension
[mm(inch)] [mm(inch)]
[mm(inch)]
±0.2 +0.3(+0.011)
5.6(1/4)
(±0.007) -0.2(-0.007)
±0.2 +0.3(+0.011)
7.1(1/4)
(±0.007) -0.2(-0.007)
±0.2 +0.3(+0.011)
9(3/8)
(±0.007) -0.2(-0.007)
±0.3 +0.5(+0.019)
11.5(7/16)
(±0.011) -0.2(-0.007)
±0.3 +0.5(+0.019)
13.3(1/2)
(±0.011) -0.2(-0.007)
±0.3 +0.5(+0.019)
13.5(1/2)
(±0.011) -0.2(-0.007)
±0.4 +0.5(+0.019)
17.5(11/16)
(±0.015) -0.4(-0.015)
Tightening Torque (kgf • cm)
Silver solder
d1 E
Standard Min.
Allowance
dimension [mm
[mm(inch)]
[mm(inch)] (inch)] (inch)]
±0.2 6
3.4(1/8)
(±0.007) (1/4)
±0.2 7.9
4.5(3/16)
(±0.007) (5/16)
±0.2 9.5
5.8(1/4)
(±0.007) (5/16)
±0.2 11
7.7(5/16)
(±0.007) (3/8)
±0.2 12.5
9.4(3/8)
(±0.007) (1/2)
±0.3 17.5
11.4(7/16)
(±0.011) (11/16)
±0.4 18.5
13.3(1/2)
(±0.015) (3/4)
AC power : L,N,1(L),2(N), Communication : F1, F2
F L d2
Min. Max. Standard
Allowance
[mm [mm dimension
[mm(inch)]
(inch)] [mm(inch)]
5 20 4.3 + 0.2(+0.007)
(3/16) (3/4) (3/16) 0(0)
9 28.5 8.4 + 0.4(+0.015)
(3/8) (1-1/8) (1-3/16) 0(0)
9 30 8.4 + 0.4(+0.015)
(3/8) (1-3/16) (1-3/16) 0(0)
13 33 8.4 + 0.4(+0.015)
(1/2) (1-5/16) (1-3/16) 0(0)
15 8.4
(5/8) (1-3/16)
34 + 0.4(+0.015)
(1-3/8) 0(0)
13 8.4
(1/2) (1-3/16)
13 38 8.4
(1/2) (1-1/2) (1-3/16)
+ 0.4(+0.015)
0(0)
13 43 8.4
(1/2) (1- 11/16) (1-3/16)
14 50 8.4 + 0.4(+0.015)
(9/16) (2) (1-3/16) 0(0)
20 51 8.4 + 0.4(+0.015)
(3/4) (2) (1-3/16) 0(0)
t
Min.
[mm
(inch)]
0.9
(0.03)
1.15
(0.04)
1.45
(0.05)
1.7
(0.06)
1.8
(0.07)
1.8
(0.07)
2.0
(0.078)